1970 Mercury Cougar

Concours reproduction with FoMoCo rectangular stamp. Used on all 1968 - 1973 models with 2-1/4" exhaust. Used on the rear section of the exhaust pipe next to the gas tank. Used in conjunction with tail pipe hangers. Clamp only, Sold individually. This is a Scott Fuller reproduction.

Reproduction dual exhaust tip to hanger clamp for the 1967 - 1970 Mercury Cougar and Ford Mustang.

Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.

Used distributor clamp and bolt, for any FE Engine: i.e. 352 / 360 / 390 / 410 / 427-4V / 428 / 428CJ / 428SCJ built from 1958-1976. Bolt may be used, or new from AMK Products. Ford part number B8A-12270-A.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

New replacement mounting clip as found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

Used clip found on select alternator wiring harnesses 1968-70 Mercury Cougar and Ford Mustang and others. Black plastic clip that tapes to the alternator harness and allows harness to be attached to one of the threaded lugs on the reverse of the factory alternator.  Ford part number C6AB-14A163-K.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Very hard to find clip that fastens the chrome power window switch bezel to the door panel. Two required per bezel. Ford part number D0AZ-14570-A. *NOTE* Early 1970 Models used the 1969 style of bezel and did not use this clip. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Used dash pad clip for any 1969-70 Mercury Cougar or Ford Mustang. This clip attaches to the steel dash assembly. The lower portion of the padded dashes just above the glove box door and steering column is where they attach. We have seen anywhere from 2-4 or zero of these clips installed on 1969-70 Cougars. According to Bill Q. these clips prevent the sharp dash pad screws from coming into contact with wiring or wiring harnesses. His go-around is to only use blunt screws (without a point) for...

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Clip or X-washer for attaching the emergency brake lever inside the rear brake drum. Fits 8 and 9 inch rear axles. Literally used on most all Ford products from 1965-73 and likely beyond. Also called a retainer for the parking brake lever pin. The long ears get squeezed with a good set of pliers for attaching. Replaces Ford number 91A-2106. 

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible.

Special clip for attaching the pull cable to the right or left fresh air vent on any 1969-70 Mercury Cougar or Ford Mustang.

Exact copy of the hard to find original. This two piece clip is used to mount gas and/or brake line to floor pans.

Partially dipped clip for attaching the fuel line harness or trunk wiring harness, or fuel line at fuel tank. Found in various places on 1967-70 Mercury Cougar and Ford Mustang.

Reproduction clip for attaching the 1969 front fender extension moulding / trim and the 1970 hood moulding / trim found on the Mercury Cougar. The 1969 application calls for 2 of these clips along with 1 larger clip per side. If you need the larger clip for the 1969 front fender extension moulding / trim, you can get'em right here. The hood lip brightwork for the 1970 requires 4 per side.  *NOTE* The threaded stud on this clip is a little longer than the original ones. This...

Used clip for attaching the moulding / trim to the front fender extension on the Mercury Cougar. Three of these clips (with long studs) are used per side to attach the 1970 aluminum extension moulding / trim. We do not currently offer a proper reproduction for this clip. We do have this reproduction clip here and it will work for the top positions, but the stud is to short to work on the lower portion of the fender extension moulding / trim. *NOTE* Some 1970 Cougars used 2 of the 1969...

Used hood lip moulding / trim clip for the Mercury Cougar. Ten of these clips (five per side) are required to mount the two aluminum "L" shaped hood lip mouldings to the 1970 hood. These clip are for the purest who places a high value on originality. If originality is not an issue, you can get our inexpensive reproduction clips here and save a little of that hard earned money.

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Used clip for the stainless steel rear deck / trunk lid moulding / trim for the Mercury Cougar. This clip will also work on the 1967-68 aluminum rear deck / trunk lid moulding / trim. Seven of these units are required per moulding / trim and the acorn nut will have some rust on it. If originality is not a issue, you can get our reproduction clip here and save a little of that hard earned income. For more insight on this tricky trunk trim, check out our video below: ...

Reproduction rocker moulding / trim end clip for the Mercury Cougar. This clip is a steel clip with a wire like the original. These units are technically for the 1969 and 1970 Cougar, but they will also work well with the 1968 rocker moulding / trim. Four of these clips were used on all 1969 Cougars except for the Sport Special which used two. The 1970 Cougar also uses two per car. Sold individually.Will work on 71-3 with modification. ...

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

Correct plastic rocker moulding clips with Ford engineering # C9WB-6510182-A, Ford part #C9WY-6510182-A. There are five of these on each side for a total of ten per car. These same clips can be found on 1977-1979 Mercury Cougars and Thunderbirds. Most likely they were used on other FoMoCo products. If you know of other applications where these clips can be found let us know so we can post the information to help others in their search. Sold Individually.

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. This particular clip is used on many Ford cars throughout the 60's and 70's. This listing is for a box of 100 clips. We recommend buying...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Known to have been used on 1969-70 air conditioning boxes to hold a vacuum hose.Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

These clips are found on the power window swtiches of the 69 - 70 Cougar. Each power window switch has one of these clips and one of the J hook clips. 6 small clips required per master switch panel, one for each window switch and two per lock out switch. 

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

Non-original style replacement clip for mounting the quarter window regulator arm to the window channel bracket on all 1969-70 Cougar and Mustang coupe and convertibles. This clip will work with either the 1969-early 1970 bracket and the late 1970 bracket. The late 1970 brackets used a unique spring steel clip that seldom is reusable. Sold individually, one each per window.

Partially dipped clip for attaching the seal on top of the radiator core supports. Often times with air conditioning the seals were installed. The factory sometimes used staples, sometimes clips. You would have to investigate your core support for staple holes. 5 clips are typical for attaching the seal. Spread them apart to where it looks equal. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. ...

This is the speedometer cable clip that connects to the firewall and transmission tunnel. Replaces Ford Part # : 373829

Six required per car.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject.