1970 Mercury Cougar

Used grade "B" driver side (left hand) backup / reverse light bezel / housing for the Mercury Cougar. These bezels may have slight cracks and pits in the chrome. The socket and pigtail will be in good condition and there will be no warp-age from over-tightening. There will most likely be thin chrome on the outer edges and other minor blemishes in the chrome. These are perfect for a driver quality car. No exchange needed on this unit.Ford part # C9WB-15500-B. ...

Used grade "A" backup / reverse light bezel / housing for the passenger side (right hand) of the Mercury Cougar. Our bezels are the best we can find with no cracks or pits. The chrome will be bright and almost completely free of lines or speckles. The socket and pigtail will be in good condition and there will be no warp-age from over-tightening. There will most likely be thin chrome on the outer edges and other minor blemishes in the chrome. These are perfect for the unrestored, low mile car...

Used grade "B"  backup / reverse light bezel / housing for the passenger side (right hand) of the Mercury Cougar.  These units may have some cracks and pitting in the chrome. There will most likely be thin chrome on the outer edges and other blemishes in the chrome. The socket and pigtail will be in good condition and there will be no warp-age from over-tightening. These are perfect for the daily driver quality car. No exchange needed. Ford part # C9WY-15500-A. *NOTE*...

New Old Stock passenger side (right hand) rear maker light bezel for the Mercury Cougar. These same bezels can also be found on other full size 1970 Mercurys. Bezel and lens as shown.Ford part # D0MB-15A466-A and D0WY-15A200-E.

This kit consists of 3 single switch bezels identified with a D0WB-14507-A casting number and one master switch bezel with a C9AB-14A432-C casting number. You will need to add the black detail paint in the lettering and trim areas.Only cores with very minimal pitting can be given full credit as removing pits from the lettering and recessed border are pretty much impossible to do.

No scratches and not yellowed like most. These were only used on the standard Cougars but will work on XR7. Sold individually, four required per car.Also sold in a set of 4

Not rusty or dinged, used on the 69-70 xr7 and Eliminator but will work on your standard model Cougar. They most likely will need repaint.  Sold individually, four required per car.Also sold in a set of 4

No scratches and not yellowed like most. These were only used on the standard Cougars but will work on XR7. This listing is for a set of 4 Also sold individually

Not rusty or dinged, used on the 69-70 xr7 and Eliminator but will work on your standard model Cougar. They most likely will need repaint.  This listing is for a set of 4 rings. Also sold individually

Reproduction pair of parking light bezels. Applications include 69 - 70 Mercury Cougar, 1969 Ford Mustang Shelby GT-350 and GT500, 1970 Mustang Sport Lamp Bezels, 71 - 72 Maverick Grabber, 1973 - 1974 Maverick (until 8/12/74) and 1971 - 1974 Comet. Replaces Ford part # C9WY-13210-A for the passenger side, C9WY-13212-A for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

Good used pair ready to be cleaned and installed with no obvious blemishes. Applications include 1969-70 Mercury Cougar, 1969-70 Ford Mustang Shelby GT-350 and GT500, 1970 Mustang Sport Lamp Bezels, and starting in 1971 these were also used on Maverick Grabber and Comets. Ford part # C9WY-13210-A for the passenger side, C9WY-13212-A for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic...

Bleeder screw for your 1968 - 1973 Cougar or Mustang Calipers.

Good used condition, hard to find with perfect chrome. Often times there will be some shrinkage in the rubber.  We cannot guarantee that we will always have the more obscure colors in stock like aqua. We seldom have black in stock. FYI

Xr7 models featured rocker switches in the center of the dash, standard Cougars had warning lights and Eliminators had this block off pad. This reproduction fits perfect and has been needed for a long time. Replaces Ford Part #: C9WY-10854.

Plastic cover that covers the hole on the bottom of the passenger side dash pad. Hole is for housing the optional map light.

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1969-70 variety, which have specific colored wires and leads....

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Used rear defog blower motor with integral fan. Ford supplied these for many years, some have different connectors on them. Some have the square style as found starting in 1973. We have a good supply of working and tested motors, so request the type of plug end you need.Replaces Ford part number C8AZ-18527-A and D3AZ-18527-A.

Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

This great new '67 Cougar "blueprint" poster is a cool display piece for any Cougar fan. We did our homework and compiled information from multiple sources, including official Lincoln-Mercury documentation and independent magazine articles about the 1967 Cougar, to create this official-looking piece. Printed on heavyweight 48lb. satin bond paper, it has the look and feel of a real blueprint, with the durability of an archival art print. Measuring a full 24"x36", it's an eye-catching piece to...

Body assembly manual used by the workers when they were originally building the Cougar and Mustang. Must have if you are putting together your Cougar or Mustang, and a great resource when tearing it down!

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

Metal reinforcing plate welded to the center of the rear body, where the 9 inch third member may come into contact with the floor. Cut from one of our many parts cars. Likely originally had a Ford part number of 4731. Removed from a 1969-70 Mercury Cougar, we suspect that it will not be a direct fit for a Mustang. This part will come as shown, spot welds will need to be drilled and the plate welded to your chassis.

New rubber body plug, fits 1-3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Typical application is rear leaf spring access.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377356.

New rubber body plug, fits 1-1/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some of the holes include: inner frame rails at radiator, center of firewall, and side of cowl.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377936.

New rubber body plug, fits 3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: frame rails at sway bar, rear floor pan, LH fender apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377977.

New rubber body plug, fits 9/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles, typically they are for: front fender aprons, transmission cross member, and radiator support. Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 376966.

Reproduction rubber body plug for the Mercury Cougar and Ford Mustang. This 11/16" x 15/16" oval unit fits to the top of the cowl underneath the front fenders. These little units are sold individually, and their are usually two required per car. Replaces Ford plug marked 383181-S.

New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan, side of cowl at door, and LH apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377949.

New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S.

44 Piece kit that includes quarter panel drain plugs.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.

Coil bracket mounting bolt for all V-8 engines as found in 1967-73 Mercury Cougar and Ford Mustang. This3/8-16 bolt attaches the coil bracket to various places on the engines. Either on the intake manifold or the cylinder head. Will fit stock Ford cast iron intakes as found 1967-73. AMK bolt B-13722.

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one long cylinder head bolt only. Longer of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Cylinder head bolt for any 1967-70 Ford 390 or 428CJ engine. This is for one short cylinder head bolt only. Shorter of the two head bolts. Sold individually, 10 short and 10 long needed for a complete engine installation. See related items for short, bolt and kit or set of 20 bolts for 390 / 428CJ engines.

Bolt for attaching the emergency brake Pedal Assembly. This is a 5/16-18 washer head bolt. Sold individually, Three bolts attach the E-brake assembly. Fits all 1969-70 Mercury Cougar and Ford Mustang.

Reproduction AC Compressor Clutch Bolt for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually

Sold individually Zinc (dark silver)

Bolts and installation kit for most 1970-73 Mercury Cougar and Ford anything, including Mustang with V-8 engines. Kit includes main pivot bolt and adjusting bolt as shown. Spacer not included, but available used.

Replaces Ford Part # 43260-S Sold individually

New screw with a correct 3/8 inch hex head for installing all armrests for all years.

3/8-16 X 4.0 GR-8 9/16 AF Zinc Dichromate Replaces Ford Part #: 370584-S

Bolt for installing the front inner and outer bumper brackets to frame rail, and rear bumper brackets to body inside of trunk. Sold individually, 8 per car.

12 Point bolt for attaching the steering column coupler to the steering box. All 1967-73 Mercury Cougar and most all other Ford, Mercury, and Lincolns. One bolt used for fixed columns, two bolts used on tilt steering columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...