Convertible

This 1965 Mustang alignment pin is not correct for the 1969 to 1973 Cougar but it will work. See the image to the left to see the comparison to an original 69 pin.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...

Good reproduction reinforcing plate, contours are like the C5ZZ-7610962-A plate which was used through 1970. Thick steel like the originals, and with same contours. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973...

14 piece bolt and screw set used to attach the convertible tack strip to the body. Kit comes with (12) 7/16 bolts and (2) phillips head screws. 

This is the storage bag that the convertible top cover folds into when the top is in the down position. Ford calls this part the "Folding top dust hood container." It is made from common vinyl top material and is always black. It measures 15"x27" and the bottom portion is sometimes, tapered down to 8". The same design was used for many Ford Products of the day including Torino, Montego and others. Current offering does not have a tapered bottom, it is square. Pictures will show both styles...

Rear most convertible top bow #4, from a 1969-70 Mercury Cougar or Ford Mustang convertible top assembly. This is the last bow and would have had a tack strip attached. Bow only, slat brackets sold separately. Ford part number C9ZZ-7651278-A.

Used to cushion and protect top vinyl from excessive wear from side rails. Unfortunately none of the reproductions that we have found resemble the OEM pads. OEM pads looked canvas on the under side that goes against the convertible top rails, and what looked like the soft side of a velcro strip on the upper side that makes contact with the convertible top itself. These are still highly recommended as they keep the convertible top rails from rubbing thorough the convertible top. "I found WCCC...

Driver side convertible frame assembly mounting and pivot bracket for all 1969-70 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Passenger side bracket with attached convertible arm only. Mounts behind the quarter interior panel. Ford part number C9ZZ-7653119-A.

Passenger side convertible frame assembly mounting and pivot bracket for all 1969-70 Mercury Cougar and Ford Mustang. Does not include the hydraulic cylinder bracket, cylinder mounting bracket sold separately. Bushings, bolts, and specialty fasteners not included. Passenger side bracket with attached convertible arm only. Mounts behind the quarter interior panel. Ford part number C9ZZ-7653118-A.

Detachable mounting plate for installing the driver side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A19-A.

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Here is a time and money saving package deal for the person restoring their 1969 Cougar. This package includes: Right and Left Hood lip mouldings Fender extension mouldings (eyebrows) Deck / Trunk lid moulding Six Piece Convertible Windshield Trim Kit Front and rear Award Winning Bumpers Keep in mind we will often give extra core value trade in for items we may be low on. Please call before sending extra parts for trade value. All parts are show quality. The bumpers are triple plated chrome,...

Not quite as long as the original bushing, but will work. If you want the correct one, we occasionally get in the NOS version of this bushing. Call us for the availability of the NOS bushing. Replaces Ford Part #: C3AZ-5422841-A.

Reproduction front tack strip for the front bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the front bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 feet (60 inches) of material and will have to trim the tack strip to fit...

Galvanized three piece replacement tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

Reproduction stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. Ford part number: C9ZZ-7654676-A

This is the restored stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. This is a very hard part to come by in good shape. Many times body shops will lose this piece while replacing the top.Ford part number: C9ZZ-7654676-ATHIS ITEM WILL NOT SHIP UNTIL WE HAVE RECEIVED YOUR CORE. ...

Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks. The original tops would have been double texture PinPoint Vinyl. There are 3 different materials currently offered for these premium tops. Single Texture PinPoint Vinyl (GOOD): This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top. It is often referred to as an OEM replacement, but that is not exactly accurate...This is a two-ply composite...

This new single texture two ply denim convertible top is an inexpensive top that is only recommended if you car is going to be stored indoors.*NOTE* This is the convertible top only. Top bows, tack strips, and tension cables are NOT included with this item.Have you ever wondered how a convertible top is installed, or maybe considered trying it yourself? Check out our installation video below! ...

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

100% complete top frame as removed from a 69 - 70 Cougar. These tops are identical to Mustang with the exception of the rear bow being slightly higher on a Cougar. We carefully break this down by removing the header and crossbows and placing the original bolts back in the holes. Once you get this from UPS it will be very evident how it goes back together.

Used convertible top flapper stopper. Technically called a "lasting", this is the thin strip of 1/16" thick metal that slides inside the sleeve of your convertible top to keep it from flapping. We will rarely have these on hand, so we've included the dimensions so that you can fabricate your own if needed. 2 required per vehicle.

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

This Cougar Logo is a favorite of any Cougar Fan. The Cougar became so popular that soon after the Cougar was released all Lincoln - Mercury Dealerships used the phrase "The Sign Of The Cat" in their advertising. These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and sound. Very nice carpet floor mats that make for an ideal gift for that Cougar lover...

Attractive XR7 embroidered logo, correct in design for any year of Cougar 1967 - 1979. These quality mats are made in the USA by Auto Custom Carpets. They are a good fit with an aggressive grip rubber backing. These are heavy mats that will not easily slip out of place or become "wadded up" under your brake pedal. They will hold their form for many years and do more than just enhance the look of your Cougar, they will provide an extra layer of insulation providing an added barrier for heat and...

These floor mats were available as part of the factory "protection package" or as a dealer accessory when these cars were new. Good used originals have gotten VERY hard to find. At present (9-20-18) they are only available in black. Keep in mind the 69-73 convertible used a narrower mat to clear the inner rockers. We have a diagram that shows you where to trim for your convertible. The walking Cougar logo is a favorite of any Cougar fan. The Cougar became so popular that soon after the Cougar...

This fusible link is a section of wire connecting the starter solenoid on one end and wiring harness that passes through the firewall to mate with the top switch wiring. Correct for power sunroof equipped Cougars. May also work for XR7 and Standard convertibles.

Reproduction bolt in four piece clear glass set for the 1970 Mercury Cougar convertible. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...

Reproduction bolt in four piece smoked glass set for the Mercury Cougar convertible. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. Then there is this version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original...

Reproduction four piece bolt in tinted glass set for the 1970 Mercury Cougar or Ford Mustang convertible. This set does not come with any window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...

Ground wire for convertible pump motor. Short wire section that attaches to the pump motor and grounds to the chassis of any 1969-73 Mercury Cougar or Ford Mustang. Easy to copy, #10 gauge wire about 11-1/2 inches long. Two ring terminals attached. Easy peasy.

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Bolt for the under side convertible plate on any 1969-73 Mercury Cougar or Ford Mustang. 6 total bolts needed for attaching reinforcement plate to undercarriage. Sold individually. These are a close match to the original bolts, which are 3/8-16 x 1-1/2". Ford tightening specs. are 25-38 lbs. ft. torque.Replaces Ford number 57048-S2.

Exact fit, not generic 'One Size Fits All' hoses. Quality high pressure fittings. Contains both the upper and lower Hydraulic Hose for a 1969 or 1970 Mercury Cougar or Ford Mustang Convertible Hydraulic Cylinder.

Connecting to the Convertible Frame Lift Lever and the Convertible Hoses, the Convertible Top Hydraulic Cylinder creates pressure from the fluid transferred by the hoses. Each Hydraulic Cylinder consists of light-weight aluminum casing, a durable steel rod, and includes all bushings and gaskets. Part is made through innovative engineering and rigorously tested to provide you with the best in functionality and long-term dependability.  Precisely crafted with high grade materials...