1970 Mercury Cougar

Original two piece assembly that bolts to the passenger side of your firewall on AC equipped Cougar's. Comes as taken from parts car. If you own a 1969 Cougar you will need to look at the configuration of the evaporator lines. During the 1969 model year this grommet bracket changed to reflect the running year change. Ford part # C9ZA-19B588-C.

These are reproduction heater hose grommets for the heater hose to pass through the firewall. Most of the firewalls that we have seen have a flared opening for the hose without a grommet. Save your hoses, buy some grommets?

Ground wire for convertible pump motor. Short wire section that attaches to the pump motor and grounds to the chassis of any 1969-73 Mercury Cougar or Ford Mustang. Easy to copy, #10 gauge wire about 11-1/2 inches long. Two ring terminals attached. Easy peasy.

Features 274 pages / 750 photos/ 12,300 items / history / finishes / measuring and more. This book provides detailed information about the fasteners specified in assembly manuals and parts books. All 12,300 fasteners are referenced to a photo! Must have for anyone wanting to correctly put together a 1955-1973 FoMoCo product.

This reproduction 2 1/4" Tri-Y H pipe to be used with the Patriot style headers on your 1970 Cougar or Mustang.

This reproduction 2 1/4" Tri-Y H pipe to be used with the Scott Drake style headers on your 1970 Cougar or Mustang.

This direct replacement is the 2-1/4 inch H pipe only, and is for any 1970 Mercury Cougar or Ford Mustang with stock 2V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and custom made for dual exhaust on any 1970 Cougar and Mustang with the 2 barrel H code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351W, 1970 351C-4V, or 1971-73 Cleveland...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock 4V cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 4 barrel M code 351C engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351 Windsor, 1970 351C-2V, or 1971-73 Cleveland...

This direct replacement is the 2-1/4 inch H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the passenger side spacer. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/2 inch diameter and have OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please...

This direct replacement features a larger than stock diameter of 2-1/2 inches for increased performance. This is the H pipe only and is for any 1970 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds without the spacer on the passenger side. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar and Mustang with the 428CJ engine. We also sell this H pipe in a 2-1/4 inch diameter and have OEM style...

This direct replacement is the 2-1/2 inch H pipe only and is for any 1969-70 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/2 inch aluminized pipes and made from an original 1970 Cougar Eliminator and Boss Mustang  with the G code Boss 302 engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Please allow 2 - 3 weeks for delivery. ...

New hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Replaces Ford part number 380699-S.

Reproduction halogen headlight conversion kit. Included in this kit are the four halogen headlight bulbs (2 high and 2 low) and the mini-relay kit, which is needed when installing halogen bulbs on your 69 - 73 Cougar. Bulbs included in this kit are "cool white" which actually have a bit of a blueish tint to them. If you would like to go with a more original "natural white" color, you can buy the inner replacement bulbs. This kit comes with the 'mini' relay kit which is designed to handle...

Reproduction replacement halogen bulb for your headlights. This is a clear bulb, "natural white" alternative to the "cool white" bulbs included in our halogen headlight conversion kit. 55 Watt Xenon Halogen H4/9003 bulb. Sold Individually.

Reproduction plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Late 1970 used the same as the 1971-73 model.Replaces Ford part # D0DZ-10718-A.

Used plastic battery hold down for the Mercury Cougar or Ford Mustang. According to the Master Parts Catalog, late 1969 through mid 1970, Cougars and Mustangs used these black plastic units. Probably introduced at the same time in very late 1969 as when the hold down clip was used to attach to the battery apron? Replaces Ford part # D0DZ-10718-A and casting number D0DB-10755-A. 

Used chrome end for the grab handle found on Mercury Cougar XR7 and several other Lincolns like the Continental MK III. Seldom will these be perfect, most have some pitting on the top sides. Fortunately they can be switched end for end and the pitting side can be installed downward. These units are sold individually.Mercury part # C9MB-5422668-A or D0MB-5422668-A.

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

For all H code 351-2V engine codes with singles exhaust. Includes 1970 351C or Cleveland engines. Holds the rear of the muffler to the passenger side underside body. Ford part number C9WY-5260-A.

Good used tail pipe hanger with decent rubber still attached. Mounts to the frame on the right side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1968 - 1970 dual and single exhaust Cougars, all engines. 1970 differs in that the tail pipe clamp was spot welded to the hanger. When you look closely on the 1970 version you will see that there is an alignment hole in the bracket and an alignment tab on the clamp. Also the 1970 version had a less pronounced gusset at...

Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. All 1970 dual exhaust Cougars, all engines. Originally the tail pipe clamp would have been spot welded to the pipe, rarely will we be able to provide these with the original clamp in place. Ford part number DOZZ-5260-C.

For all H code 351-2V engine codes with single exhaust. Includes 1970 351C or 351W engines. Includes one tail pipe hanger and one muffler hanger, both of which mount to the passenger side of the car.

Reproduction Concours Correct muffler hangers for your 1968 - 1970 Mercury Cougar.

Muffler mounting tabs for using factory Ford muffler hangers on aftermarket turbo style exhaust mufflers. These help achieve that concours look using a replacement muffler or mufflers. We recommend using your existing horse shoe shaped muffler hanger as a jig for locating these tabs prior to welding. These were copied from the original style tabs found on most 1968-73 Mercury Cougar and Ford Mustangs. 1967 cars and some Mustangs used a single transverse muffler behind the rear axles, these may...

Our used handles do not come with this linkage part so if yours is missing this is what you need. Comes with mounting screw as shown.

D0AE-6316-A All 1970-73 351C-2V and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. There is a $50 core charge for this part.*Note - Excludes 1971 and later 351-4V engines. **Note - When ordering double check that you have a 351 Cleveland engine. It is not...

D0AE-6316-A All 1970-73 Mercury Cougar 351C-2V engines, and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. We save the very best used harmonic balancers, those that do not actually need rebuilding. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. Price includes $55 core charge. Refundable $50.00 core...

Includes all 1970 H code 351-2V Windsor engines only. The D0OE-6316-C harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/4 inches, and 3/4 inches thick. 351-2V Cleveland and 351-2V Windsor engines were both used in 1970, they each have specific balancers, please identify your engine and verify your balancer numbers. Has the timing marks on rim. Refundable $50.00 core charge when rebuildable D0OE-6316-C harmonic...

Includes all 1970 H code 351-2V Windsor engines only. The D0OE-6316-C harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/4 inches, and 3/4 inches thick. 351-2V Cleveland and 351-2V Windsor engines were both used in 1970, they each have specific balancers, please identify your engine and verify your balancer numbers. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be...

Includes all X code 390-2V, S code 390-4V, GT-E W code 427, and 428 Cobra Jet engines 1968 - 1970 only. The C8AE-6316-A harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7 inches, and 1-1/16 inches thick. Has the timing marks on rim.  The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to...

Includes all X code 390-2V, S code 390-4V, GT-E W code 427, and 428 Cobra Jet engines for 1968-70 only. The C8AE-6316-A harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7 inches, 1-1/16 inches thick and has the timing marks on rim. Refundable $50.00 core charge when a rebuildable C8AE-6316-A harmonic balancer is received by WCCC. Ford part # C8AZ-6316-B, Ford casting # C8AE-6316-A.*NOTE* Excludes 1967 S code 390-4V...

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable C8AE-6316-C core at WCCC. *Note - Excludes 1969 - 1970 428 non dragpack Cobra Jet engines.Click on images...

ETA FOR THIS ITEM IS 8/23/2023Decent off shore part. Since good used cores are very expensive and almost impossible to find this is often the only choice.

Ford casting number D0ZE-6316-A Includes all 1970 G code Boss 302 engines. Ford master part number D0ZZ-6316-A. Has the timing marks on rim. This is a rebuild service only, your core harmonic balancer will be sent to our rebuilder, allow 3-4 weeks turn around. 3 - 4 weeks after we receive your rebuildable D0ZE-6316-A core at WCCC. *Note - Excludes 1969 Boss 302 and all non-Boss 302 engines.Click on images to enlarge. This is a picture of a 40 year old piece of rubber removed from a harmonic...

Very nice reproduction of the D0ZZ-15525-A 1970 Mercury Cougar and Ford Mustang 4 speed backup light wiring harness, with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Reproduction radio to door harness for your 67 - 70 Cougar or Mustang.

Perfect fit, easy to replace and will be a great upgrade over your original scratched and or pitted knob. To remove, reach behind the dash and locate the small, round spring loaded button on the top side of your headlight switch. Depress the button while firmly grasping the knob and move back and forth until it releases. To install, firmly and quickly press the knob inward (towards the dash) with the palm of your hand. NOTE - This does not fit Mustang headlight switches  Here is a helpful...

Screws and spring clips for the tank or reservior for vacuum system

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16A and "H", There are four different versions used, but they are the same for the 1969-70 Mercury Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68, but was moved...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used on 1967-68 Mercury...

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up. If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much easier to find inner, high beam lamp distinguished by the number 1 at 12...

Reproduction 4001 incandescent (non-halogen) high beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 2-prong plug and mounts in the inboard position on the car.These are OEM wattage (50 watts) to work with the factory headlight switch, without the need to add relays like you would for higher wattage halogen bulbs.Replaces bulb number 4001. Sold individually, 2 required per car.

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...