1970 Mercury Cougar

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "H", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68 Mercury...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "RL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Converting your headlight wiring to a modern relay type is probably one of the best 'bang for the buck' mods you can do to your classic car. A must when using modern halogen bulbs, it will also brighten your original incandescent headlights. Normally this is done by cutting the main wiring harness and splicing in a pair of relays. Most of us try to hide the relays under or behind something as well. Not only is this a time consuming task, it can be troublesome if a connection or component fails...

The Mini Relay Kit has everything you need to add relays to your headlight circuit - without cutting your wiring harness. It is equivalent to installing relays into your main harness like it was done for years, but requires no modification to the wiring harness. The differences between this kit and the full kit are redundancy and controller size. This kit has only one controller with two relays designed to handle up to a maximum of 200 combined watts and uses a wiring harness to control...

Complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 1969 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness.NOTE: From the factory, Ford made the alignment tabs different passenger vs driver side...

Reproduction complete set of halogen projection headlight bulbs for your 67 - 73 Cougar or 69 Mustang. Integrating the newest modern projection headlight technology into a slim compact bulb, these headlights will fit right into your existing headlight bucket. Each kit comes with the proper wiring adapters so all you need to do is plug one end into the bulb and the other end into your headlight harness. NOTE: From the factory, Ford made the alignment tabs different passenger vs...

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

Reproduction BLACK Headliner with Sunroof for the 1969 and 1970 Mercury Cougar. Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel. On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will...

Correct Reproduction BLACK Perforated Headliner for the 1969 & 1970 Mercury Cougar Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.

We have finally found a supplier that produces the correct DARK BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Reproduction dark green headliner for your 1969 Cougar. Remember that this dark green color is specific to 69. We're still in the process of trying to get the right color for the 70 Cougars, so sit tight, we'll have them soon!

We have finally found a supplier that produces the correct DARK RED perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

We have finally found a supplier that produces the correct LIGHT BLUE perforated headliner for your 1969 or 1970 Cat! Available Colors: White, Black, Dark Red, Light Blue, Dark Blue, and Saddle. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

We have finally found a supplier that produces the correct Medium Brown perforated headliner for your 1970 Cougar. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.

We have finally found a supplier that produces the correct SADDLE perforated headliner for your 1969 or 1970 Cat!Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

Two piece kit, one piece for the headliner, and a second piece for covering the sunroof panel.On early production cars Ford pulled the cars off the assembly line to sent them to ASC Golde for install. Golde used 3 bows for installing the headliner, whereas in later production Ford used 2 bows when installing them on the assembly line. These headliners are for 2 bows installations. If you have 3 bows, you will need to order a standard headliner, then cut it to fit. Check out our video below...

Available Colors: White, Black, Dark Red, Medium Blue, Dark Blue, and Saddle.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.

Pair of used wire anchors for keeping the rear most headliner bow stationary. These are fragile wires, and prone to rusting. We try to keep them in inventory. 1969-70 anchor wires are 3-1/16 inches long. A DIY person can improvise these pretty easy, using lengths of regular wire.

Contrary to what you might think at first glance, the support rods used in 1969 - 1970 Cougar headliners are not the same front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must keep the rods in the same order as they came out of the original headliner. 5 Rods total. Once installed in the car, each rod should be about the same distance from the roof as the other rods. WCCC marks the bows with a sharpie pen, 1 hash mark, 2 hash...

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

This is the heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 2 Barrel Carburetor and the 351 Cleveland engine. Exact OEM standards and specifications. Correct fiberglass insulation, fittings and S clip.

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up.  Made out of OE Steel.  This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.

Exact OEM standards and specifications.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This 8 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 4 Barrel Carburetor, where the choke tube enters through the side of the choke housing.

This 7 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 2 Barrel Carburetor, where the choke tube enters through the bottom of the choke housing.

This 7 piece kit is for 1969 or 1970 Mercury Cougar and Ford Mustang with the 351 Windsor and a 2 Barrel Carburetor, where the choke tube enters through the bottom of the choke housing.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

*NOTE: This item comes un-painted from the manufacturer.Very correct reproduction of an impossible to find part. The only difference I can detect is that this original weighs just an ounce or two more than the original. Click on images to enlarge. Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the...

Factory installed, used engine mount heat shield, for any 1969-70 Boss 302 Mercury Cougar Eliminator or Ford Mustang. Mounts to the driver side mount and the asbestos portion lays under the exhaust manifold. Basic Ford part number is 6C038 for motor mount heat shields.  *Note - this item will likely not work with headers.*Note - this part does contain asbestos.

Grade B exhaust manifold heat shield for any 1970 Mercury Cougar or Ford Mustang with 351C engine, 2V or 4V, it doesn't matter. Uses a separate, small diameter metal tube (part number D0OZ-9652-A) that attaches to the 1970 Cleveland air cleaner snorkel. Grade B used will have minor pitting, and may have small holes and or rough rusted edges. When mounted it would be difficult to see the defects. We also stock A grade versions.Replaces Ford part number D0OZ-9A603-F.

Since we have a difficult time keeping grade "A" Windsor heat shields in stock we also offer a driver quality version. This unit will be very thin from rust in certain areas. C9OZ-9A603-A Metal shroud and tube assembly that attaches to the factory 1968-1969 air cleaner assembly on all 351 Windsor engines both H code 351-2V and M code 351W-4V (1969 offering only). *Note - for 1970 this shield is used after build date of 2-2-1970, but could be used on prior dates. We suspect that the early 2...

D0AZ-9A603-C This is a two piece metal shroud unique to early production 1970 H code 351-2V Windsor Cougars. Due to problems Ford had with this design they returned to the 1969 style later in the year (after 2-2-70). *Note - 1970 351-2V Windsor cars build before 2-2-1970 used a two piece heat shield. Also used air cleaner snorkel D0OZ-9A626-B and a paper 'S' tube. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts....

*NOTE: This item comes un-painted from the manufacturer.Another spot on reproduction! Correct for CJ and SCJ.  Comes with brackets and hardware as shown. Click on images to enlarge. ...

Reproduction heater blower motor for Mercury Cougar and Ford Mustang. Wiring will need to be spliced into your existing wiring harness. Save the squirrel cage and the heater motor mounting plate from your old unit because it is not included with this item.These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units....

Usually ships in 3-5 business days. Reproduction heater box with A/C for 69 - 70 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). This assembly comes with two heater core gaskets, one for early 69 and one for late 69 - 70. NOTE: We've received some helpful...

Used heater box assembly for any 1969-70 Mercury Cougar or Ford Mustang (V-8). The pictures in the sequence above are reference pictures, grade B boxes will have cracks or breaks. Comes as shown, box with damper doors and levers on the side. We recommend buying a heater core and foam rebuilding kit to go along with this. Save your old fan motor and plate, this unit does not come with a fan assembly. Grade B used, will have a crack or chips in the fiberglass. Fair condition, will need a...

Basic clam shell box as shown for cars WITHOUT AC. Keep in mind we have nice original FoMoCo units for less money! *NOTE*Kit does not contain heater blower motor, squirrel cage, or blower motor mounting plate. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts apply to other years. ...

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. Replaces part # C9ZZ-185188-A.

C9ZZ-18A651-A Complete heater control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic knobs and the lever borders. Knobs and light socket wiring harness not included. *RESTORATION TIP* If you like to restore your own parts, you can purchase plastic polish for the lenses that will take out the haze with a bit of elbow grease. A...

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...