1970 Mercury Cougar

Driver side rear mounting bracket for the 1970 Mercury Cougar front fender side marker lights. They will not be bent or heavily rusted. The drivers side has an engineering number of D0WB-15A431-A and the passenger side has the number D0WB-15A**** stamped into it.

Passenger side rear mounting bracket for the 1970 Mercury Cougar front fender side marker lights. They will not be bent or heavily rusted. The drivers side has an engineering number of D0WB-15A431-A and the passenger side has the number D0WB-15A**** stamped into it.

Used bracket for mounting a steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Main bracket only, there is also a side support bracket that is also needed. Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Tilt and fixed steering columns.Ford part number D0AZ-3676-A.

Floor mounting column bracket for the 69-70 Cougar or Mustang. Rubber gasket may not come with bracket, and if it does will most likely need replacing. Undamaged with original fasteners. Get the gasket here.Ford part number C9ZZ-65017A50-A.

Weld in bracket for attaching the trunk lock striker on any 1969-70 Mercury Cougar. Majority of these have rust forming at the base where it meets the trunk floor. Removed from a rust free western Cougar. Ford part number C9WY-6543235-A.

Used mounting tab or bracket, that is embedded into the dash pad below the instrument cluster for attaching the lower dash filler. These can be glued back into the foam with adhesive. Right and left side pieces are different, this one attaches to the lower left side. The companion bracket is also available.

Used mounting tab or bracket, that is embedded into the dash pad below the instrument cluster for attaching the lower dash filler. These can be glued back into the foam with adhesive. Right and left side pieces are different, this one attaches to the lower right side. The companion bracket is also available.

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific. 

Rear Wheel Cylinder (29/32", Right Hand) Fits either Right Hand or Left Hand. Sold individually, 2 required per car. Replaces Ford Part #: C3OZ-2262-B and D2ZZ-2262-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Reproduction passenger side (right hand) wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits into a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part # C3OZ-2061-B, D2ZZ-2061-A, & D3ZZ-2061-A.

Reproduction drum brake backing plate hole cover plug. Replaces Ford Part # 8A-2092.

Used driver side (left hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar or Ford Mustang, and Fairlane / Torino equipped with 351 or larger V8 engines. Ford part # C9OZ-2013-B. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

Used passenger side (right hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino equipped with the 351cid or larger V8 engine.Ford part # C9OZ-2012-A. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Quality rebuilt LH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out out video on converting from drum to disc brakes below: ...

Quality rebuilt RH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out out video on converting from drum to disc brakes below: ...

Replaces Ford Part # 382713-S Sold individually

Sold as a Pair. Ford Part #: C8AZ-2B296-A

part# 384114-S100 Sold individually

Used drum brake distribution block for Mercury Cougar and Ford Mustang equipped with front drum brakes. This unit mounts to the driver side fender apron with two nuts. Bare block without brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # D0OZ-2B257-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

These new brake drums are perfect replacements for tired and thin originals on you Cat or Pony. Fits cars with either the 2 1/4 inch or 2 1/2 Inch shoes. Front drums do not include studs or a hub. Drums Provide Consistent Quality & Reduced Noise.; Drums Are Vehicle Specific & Meet Federal Safety Standards.; Castings Meet Sae J431/g3000 Specifications For Proper Tensile Strength.; Machined To Control Perpendicularity & Run-Out For Optimal Performance & Brake Life.Also fits V8...

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 71.6 mm Center Bore Diameter : 61.8 mm Maximum Discard Diameter : 256.3 mm O.D. : 296.3 mm Replaces Ford Part #:C2OZ-1126-B

Flexible high pressure replacement brake hose for front drum brakes that fits both passenger (right hand) and driver (left hand) sides of Mercury Cougar or Ford Mustang. Sold individually, please remember to order two if a pair is needed.Replaces Ford part # C7ZZ-2078-A.

Flexible high pressure replacement brake hose for the front driver (left hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-B.

Flexible high pressure replacement brake hose for the front passenger (right hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-A.

FINALLY! The correct rear flex hose for the 1970-73 Mercury Cougar. The Mustang rear steel line fitting is .323" whereas the Cougar fitting is .395". If you have purchased a reproduction front to rear steel brake line, you will want to make sure whether you have the Mustang .323" or the Cougar .395" rear fitting as some vendors sell a "Cougar" bent steel line with a Mustang rear fitting.  If you have the .323" fitting, you will need to purchase the Mustang flex hose (D1ZZ-2282-A, click...

This intermediate OE-style steel line attaches to the transmission tunnel and connects the brass distribution block in the front to the flexible brake hose in the rear of the car. Application does not change if the front is drum or disc in the front, all Cougars 1967-1973 came with drum in the back.  Not for Mustang as the Mustang had a shorter wheel base than Cougar.  Line is too long to economically be shipped without bending it over, carefully straighten it out prior to...

Reproduction OE steel power disc brake line kit for the Mercury Cougar. This item is bent and dropshipped from the supplier when it is ordered and is available in both OE steel and stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

Reproduction stainless steel power disc brake line kit for the Mercury Cougar. This item is bent and dropshipped from the supplier when it is ordered and is available in both OE steel and stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.

Reproduction stainless steel standard drum brake line kit for the Mercury Cougar. This item is bent and dropshipped from the supplier when it is ordered and is available in OE steel or stainless steel. These kits include all of the steel lines that run from the master cylinder to the wheel cylinders, but it does not include the flex tubes that connect to the calipers.  NOW AVAILABLE WITH THE CORRECT REAR BRAKE LINE FITTING FOR THE COUGAR!    The Mustang fitting is .323" whereas...

Reproduction steel lines for the drum brake master cylinder on 1970 Mercury Cougar and Ford Mustang. Connects the master cylinder to the brake distribution block. 

Two-piece OE-Style steel Rear Axle Brake Line Set 67 Mercury Cougar and Ford Mustang with 9"-28 Spline Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These mild steel lines are Galphan coated for added protection. 1970 differs from 69...

Two-piece Stainless Rear Axle Brake Line Set 70 Mercury Cougar and Ford Mustang with 9" Rear Axle. The Rear Axle Brake Lines are mounted on the axle going to the left and right rear wheels. These will either connect to a caliper hose or thread directly into a wheel cylinder. All lines come Pre-Bent and flared with the correct threaded fittings which reduces your install time tremendously. These stainless-steel lines are T304 but are of a special softer blend to help with any possible leaks. ...