Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Internal tail shaft assembly from a C-6 transmission. We only disassemble up to what you see in the picture.
This reproduction economy front emergency / parking brake for the Mercury Cougar or Ford Mustang fits from the handle to the equalizer. 1 required per car. Replaces Ford part # C9ZZ-2853-A.
Premium reproduction, near concours correct front emergency / parking brake cable for the Mercury Cougar or Ford Mustang. This cable hooks onto your inside foot activated brake assembly inside the car, through the floor board, and hooks to the brake equalizer cable under the car. This unit is very close to an OEM replacement, much better than our economy cable. ...
This used emergency / parking cable anchor bracket is spot welded to your passenger side (right hand) front floor pan and anchors the cable. Comes "as taken from parts car". *Customer Feedback* from mercurycougar.net: "Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when your talkin 'cause your important to them. Greatest thing for our hobby. Thanks Lin and Don for making/getting...
Reproduction concours correct premium grade passenger side (right hand) emergency / parking brake cable for the 1970-73 Mercury Cougar and Ford Mustang with V-8 engines. This is the long one on the passenger side (right hand) and measures approximately 133-1/8 inches long.
Reproduction emergency / parking brake cable for the Mercury Cougar or Ford Mustang with V-8 engines, that is approximately 133 1/8" long. This unit fits from equalizer to rear brakes and one is required per vehicle.Replaces Ford part # D0ZZ-2A635-A.
Premium grade reproduction driver side (left hand) rear emergency / parking brake cable. This is the short one, 31 inches, located on the driver side and is an exact fit for 1970 - 1973 Mercury Cougar and Ford Mustangs. Ford Part # D0ZZ-2A635-B
Front emergency brake cable bracket that welds to the floor under the drivers side floor board. It is spot welded to the floor pan and frame rail and is often over looked when floor pans are replaced. The unit you receive will need clean up, but will not be heavily rusted. Fits all 1969-70 Mercury Cougar and Ford Mustang.
Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A
This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.
Aluminum housing for the sunroof cable drive, connects to the motor on any 1967-73 Mercury Cougar and many other vehicles that used the Golde sun roofs. Golde was a company from West Germany and also supplied parts to many other auto manufacturers such as Mercedes-Benz, Porsche, VW, BMW, Mopar, and Ford. ASC was the company that installed sun roofs for Ford US, and they used Golde components. Casting number Golde 100 413 600 / Golde 100-413-600 / Golde 100413600. ...
Aluminum cover for the sunroof cable housing on any 1967-73 Mercury Cougar and many other vehicles that used the Golde sun roofs. Golde was a company from West Germany and also supplied parts to many other auto manufacturers such as Mercedes-Benz, Porsche, VW, BMW, Mopar, and Ford. ASC was the company that installed sun roofs for Ford US, and they used Golde components. Casting number Golde 100 413 605.
This used emergency / parking brake cable equalizer mounts to the end of the parking brake release assembly and captures the emergency brake cable. Replaces Ford part # C6OZ-2A602-A.
Reproduction cable guide for the 67 - 73 Cougar or Mustang equipped with a sunroof. These are the guides that hold the cables, and slide back forth on the sliding roof panel assembly as seen on page 14 of the sunroof manual. Sold individually.
Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford Part # C7ZZ-2A808-A.
Keeps proper tension on emergency / parking brake cable by taking up the slack when the brake is off. Hook attaches to the bracket under the passenger side floor. Replaces Ford part # C7ZZ-2A808-A.
California emission control "Caution" decal for the 1970 Mercury Cougar and Ford Mustang.
Reproduction California Emission Control Caution Decal for the 1970 Mercury Cougar / Ford Mustang
Reproduction Boss 302 California Emission Decal for the 1970 Mercury Cougar / Ford Mustang
Reproduction Bendix single piston major repair kit.Includes all major rebuild parts and new Chromoly piston
Reproduction disc brake caliper insulators for a large array of FoMoCo products starting in 1968. 2 are required per caliper, 4 total per vehicle. Sold as a pair.Replaces Ford part # C8AZ-2B299-A.
Each kit contains the seals for one caliper assembly. Replaces Ford Part #: C8ZZ-2B120 and #C8ZZ-2B121
This is the correct, original cover for your 1969-70 Mercury Cougar and 1969-70 Ford Mustang antenna. The Ford MPC calls this part a cap, it is the stainless steel rectangular piece of trim that goes on top of your factory antenna base. These are angled, so watch the orientation when installing. Most of these had a paper tag with part number and "FRONT" installed at the factory. These snap into place on the OEM factory installed antenna base. Used gasket also available.Replaces Ford part...
Dill 627 valve stem cap. Same as the 1960's cars. See related items, also sold as a set of 5 caps.
Dill 627 valve stem caps. Set of 5 caps. Same as the 1960's cars.
Reproduction disc brake master cylinder cap in gold cadmium for the Mercury Cougar or Ford Mustang. We have compared this cap to our originals, and the stamping does not match any of our originals, but the manufacturer claims that the scripting is correct. Also available in chrome! This cap will only fit master cylinder part# 15298Replaces Ford part # C7AZ-2162-B. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar...
Reproduction premium quality disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. These are considered concours correct and show quality. Check out the link below for some information on master cylinder caps: http://anghelrestorations.com/uploads/3/5/1/2/35122002/master_cylinder_caps_1.5.pdf Replaces Ford part # C7AZ-2162-B. Fits: 1969 Mercury Cougar1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang / Torino1970...
Reproduction chrome master cylinder cap for the Mercury Cougar or Ford Mustang equipped with drum brakes. This quality reproduction has the correct lettering and is correct for 1970-73 Cougars and Mustangs. However, it fits and looks good on all 1967-73 Cougars and Mustangs with other under hood chromed goodies. Will also work fit any other 1967-73 Ford drum brake dual reservoir master cylinders.Replaces Ford part # C7AZ-2162, C9AZ-2162, and D3AZ-2162.*Customer Feedback from Mercurycougar.net*"...
Due to the vulnerable location of the control valve these often get cracked or worn through from rubbing on other components. Fits most all Ford passenger cars 1962-1970. Replaces Ford part number C2AZ-3C705-B
Replaces Ford part # C7AZ-3A006-C of D1VY-3A006-A.
Replaces Ford part # C7AZ-3A006-C or D1VY-3A006-A.
1967 - 1971 Ford power steering pump dipstick. Used until 2-8-1971.
We're pleased to offer a 5 layer car cover that is composed of the thickest and most reliable fabric available in today's market. With the most technologically advanced material, this cover is guaranteed to protect your car from extreme weather conditions such as heavy rain, snow, ice, sun and wind. This heavy-duty, 100% waterproof cover insures perfect protection all-year-round for both indoor and outdoor use. It features three bonded layers of polypropylene, a micro-porous film layer...
Sold individually Zinc (dark silver)
Used carbon canister filled with charcoal or carbon particulates for the Mercury Cougar or Ford Mustang. This unit mounts to or near the passenger side (right hand) engine frame mount. All 1970 California sold Cougars and Mustangs came with this canister to comply with California's strict emission standards. Ford part # D0AZ-9D653-C, casting # D0AF-9D653-C. *NOTE* These are 40 year old canisters, at this late stage the filtering ability of the particulates are probably not that...
Reproduction polished aluminum 600 CFM "Street Warrior" carburetor for the 67 - 73 Cougar or Mustang. Replaces Holley, Edelbrock, Carter AFB, and Autolite style carburetors with 5 3/16" x 5 5/8" bolt pattern. Performance upgrade for stock to mildly modified V-8 enginesCalibrated for excellent street performance right out of the boxFactory preset electric choke for easy startupsVacuum secondaries for use on wide variety of vehicles. Compensate for all vehicle weights, gearing &...
1970 H code with 351W-2V, Autolite 2100 carburetor, automatic FMX transmission - All 50 states. D0AF-F stamped on the carburetor base, 1.21" venturi size and 351 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Without air conditioning.
1970 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. D0ZF-9510-AD stamped on the carburetor air horn. Holley list #4516, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning. Current carburetor has a date of 964 on the body. *Excludes Super Cobra Jet.
1970 428CJ-4V Holley 4150 carburetor, automatic C6 transmission - all 50 states. D0ZF-9510-AD stamped on the carburetor air horn. Holley list #4516, 735 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. *With air conditioning. This carburetor has been previously restored, we have noticed that one of the metering blocks has the wrong number. Still has the manual choke lever, and has a throttle kicker. Look carefully, some...
New Street Avenger carburetor. The 350 CFM Street Avenger carburetor has great features such as optimized street calibrations...two vacuum ports for all necessary vacuum accessories, factory preset electric choke for easy startups, built-in fuel filters; and an included 3/8" fuel line connection so there are no unnecessary trips back to the parts store. Known to bolt in right out of the box. The Avenger series are the first carburetors to have a limited lifetime warranty. With a great...
Basic kit for rebuilding your Ford Autolite or Motorcraft 2100 or 2 barrel carburetor. Covers all factory 2 barrel carburetors on any 1967-73 Mercury Cougar and Ford Mustang with Autolite or Motorcraft 2100 carburetors. Excludes later 2150 carburetors.
Carburetor idle mixture screw caps like originally came on the cars from the factory. Exact reproduction of Ford part number C7AZ-9J500-A. This clip onto the idle mixture screws of any 1967-73 Autolite or Motor Craft carburetor 2100 or 4300. They also will fit the 429 Cobra Jet with Ford numbered Rochester Quadrajet carburetors in 1970-71. Sold as a PAIR.
5/16-24 hex nut 7/16" head that is used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts. Sold individually. AMK B-12786
This is a set of four 7/16 nuts that are used to secure the carburetor to the intake manifold. If you need to replace your rusty old studs, we also carry an eight piece kit that contains the studs and nuts.
This is the complete eight piece kit that includes four 7/16 nuts and four studs (1 3/8") which are double threaded. One end is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with NO spacer.
This is the complete eight piece kit that includes four 7/16 nuts and four double threaded studs (1 3/4"). One end of the stud is fine threaded to accommodate the installation nuts, and the other end has the course threads needed to screw into the intake manifold. This is the kit used to install carbs with 1/4" to 3/8" spacers.
Replaces Ford part # 351089-S Zinc (dark silver) finish Sold individually
Factory cast aluminum two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Fits all Ford 2 barrel carburetors, bore size is 1-5/8 inches in diameter. ...