1970 Mercury Cougar

SNAKECOVER Cast aluminum valve cover. Correct on some 1969-1970 Mercury Cougar, Ford Mustang, Shelby GT-500 with 428CJ and 428SCJ engines. This is the 'Snake' aluminum valve cover. Ford master part number C9ZZ-6582-B.

C9ZE-6583-G Cast aluminum valve cover with. Correct on 1969-1970 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engine. This is the finned aluminum valve cover. Ford master part number is C9ZZ-6582-C. *Note - Most, if not all 1969 Boss engines came with a chromed steel valve cover. Research did not turn a part number for that valve cover. Likely it is a chromed 351C valve cover. If you have the part number for the stamped steel chrome Boss 302 valve cover please share. ...

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

CUSTOM ORDER, DROPSHIP ONLY. High quality reproduction vinyl top for the Mercury Cougar with sunroof that features both the correct pattern and finish. This top features a durable moisture resistant backing that will look good and last long.

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Used seat belt bolt washer for the Mercury or Ford.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

These used taillight mounting washers are sold individually for your Mercury Cougar. Two different inside diameters on these, we have them mixed, because they are in such short supply. Normally installed with a dollop of black goo for sealing out moisture. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems....

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Dated 9M6, December 6 1969. Boss 302 or 351C Ford water pump core, suitable for rebuilding. This version has a casting number of D0OE-D. Found on many Ford 351 Cleveland engines from 1970. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

NOS Water bypass plate for all Ford 351C engines. This is an original in the package brass restrictor plate for 1970-73 Mercury Cougar or Ford Mustang Torino etc.Limited to stock on hand. Replaces Ford Part number D0AZ-8K517-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Includes all five pieces. Front bow rubber seal is C9ZZ-7653986-A. Side rubber seals are C9ZZ-7651564-A, C9ZZ-7651565-A. Much better fit than reproduction, perfect for that high end restoration.

Reproduction rear deck / trunk lid weatherstrip seal for the Mercury Cougar or Ford Mustang. A cheap piece that will keep water out and keep your trunk from rusting. Replaces Ford part #: C5ZZ-6543720. While you're in the trunk, you might also be replacing your trim. For some insight on the trim, check out our video below: ...

Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion. *Customer Feedback*"I know Don Rush is a trusted and well...

Used inner and outer passenger side (right hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.*Customer Feedback*"I know Don Rush is a trusted and well...

New Dark Argent spray paint for the 69-70 Cougar or Mustang. This paint is designed for the 70 Mustang Mach 1 grille and rocker panels, but is a great match for the argent color on your Styled Steel Wheels.

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Used drivers side or left hand door window regulator for all 1969 and 1970 Mercury Cougar and Ford Mustangs. *TRIVIA* This style of regulator with the dog legged end on the lift arm, was the service replacement regulator for both 1969 glue in windows and 1970 bolt in windows. Good used regulators that we inspect for operation. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, plastic...

Ford Part #:D0WY-6523209-A.

Exceedingly hard to find in perfect used condition. Ford Part #:C9WY-6523209-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for...

Used drivers side or left door window regulator for all 1969-70 Mercury Cougar and Ford Mustangs with glued in door glass. Good used regulators that we inspect for operation. We suggest lubricating with suitable grease on all of the moving parts and the actual regulator mechanism during the installation. Comes complete with spring, white plastic rollers, and captured steel bushing with clip. The regulator used on the bolt in glass, which became standard soon after the 1970 model year began, is...

windshield defroster nozzle to vent for any 1969 - 1970 Cougars or Mustangs without air conditioning. This used grade "B" part will have more than one minor defect. It will have a small crack and possibly a broken or missing tab, but it's a heck of a lot better than wiping your windshield with your sleeve.Replaces Ford part number C9ZA-18490-A.

C9ZA-18490-A, windshield defroster nozzle to vent for any 1969 - 1970 Cougars or Mustangs without air conditioning. This part is used and is grade "A."  If it does have any minor defects, it will have only one. It might have a small crack, but will not have any broken or missing tabs. If you drive your baby when it is cold and don't have this part, you want it. Why, because it's lame when you have to use your sleeve to wipe off your windshield to see where you are going. It's also a heck...

Much better fit than the reproductions which make closing your door very difficult for the first year.Ford part # C9ZZ-7602627-A

Much better fit than our reproductions which make closing your door very difficult for the first year. Ford part # C9ZZ-7602626-A

Trico brand wiper blade refills for 1969-70 Mercury Cougar or Ford Mustang with original wiper arms

Reproduction Dash to Gauge Feed Harness for the 1970 Mercury Cougar and Ford Mustang with either the 351C-2V or 351C-4V, Cleveland engine only. Replaces Ford Part #: D0ZZ-14289-ACheck out the video below on our new gauge tester: ...

This four used piece wiring kit gives you all the factory correct wiring unique to a 1970 XR7 convertible.The rocker switch that raises and lowers the convertible top for the 1970 XR7 convertible is a unique design and uses a different plug to mate to it, as well as it uses a circuit breaker rather than a fusible link on the power feed. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit...

D0ZZ-15525-A 1970 Mercury Cougar and Ford Mustang with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Used wiring harness for any 1970 Mercury XR7 convertible. Connects the dash switch panel, and the intermediate or jumper lead. This harness is unique to 1970 XR7 convertibles. Has the four plug connectors as shown for the switch panel.Ford part number D0WY-10B923-B.* Note - 1970 XR7 only, body code 76B.

Wiring pigtail for the low fuel sending units on 1969-70 Mercury Cougar XR7 and standard models with low fuel warning light option. The Safety Convenience Option included a low fuel warning light. This pigtail has two wires which attaches to the three prongs on the 1969 C9WF-9275-C or 1970 D0WF-9275-B low fuel sending units. Ford part number is C9WB-14406-A or C9WY-14406-A. Standard wiring harnesses were supposed to have an integral plug for the single plug fuel sending units on the...

Used wiring harness that goes from the rear of the dash all the way to the blower motor in the package tray. This same wiring was used on all 1969-70 Mustangs and Cougars. 1970 Cougar XR7 models have a slightly different configuration, but utilize the wire harness.Replaces Ford part number C9WB-18C394-A.

This is a good used power wire that passes through the firewall, travels along the passenger side engine compartment and mates the the rectangular power window relay. Fits 1969-70 Mercury Cougars with factory power windows. This is a Grade A harness that has been tested and inspected. This harness will look and function correctly. We also sell a Grade B harness that will have at least one obvious repair for those folks on a budget

This wiring harness goes from the main convenience light harness to the warning light panel on in the center of the dash on the STANDARD 69 - 70 Cougar. You can find the other convenience light harness / socket here.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the Mercury Cougar XR7. It was also used on the Standard model after 3/3/1969. This is part of the 14401 main under dash wiring harness.

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Specific to 68 - early 70 Cougars and Mustangs.The only difference between the late and early pigtail is that the early plug is black and the late plug is white. No difference in wiring.

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Works on late 1970 - 1973 Cougars and Mustangs. The only difference between the late and early pigtail is that the late plug is white and the early plug is black. No difference in wiring.

Used wiring pigtail for the Windshield washer pump on the 1969 - 1970 Mercury Cougar or Ford Mustang.

Electrical wiring pigtail for the windshield wiper motors on any 1969-70 Mercury Cougar or Ford Mustang. Plug with grommet and correct color wires and an adequate amount of wire length to make a repair or splice onto the newer motors without plugs.

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

New old stock manual steering worm gear for any 1967-70 Mercury Cougar or Ford Mustang with manual steering or 19:1 steering gear box. Factory new worm gear assembly for rebuilding your steering gear box. NOS in the box Ford part number C7ZZ-3524-C. ...

Used wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...