1970 Mercury Cougar

Fits 1969 - 1970 BOSS 429 and 428 Cobra Jet - C80A-3D746-A. Blissfield Manufacturing Company was the original equipment manufacturer (OEM) for these Power Steering Coolers to Ford Motor Company. Located on the driver side strut rod support. Ford Part # C8OA-3D746-A

Reproduction multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Does not include dipstick. Manufacurers note: In place of the paper gaskets, it is recommended that you use gray atv...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction power window conversion for your Cougar or Mustang. These kits are easy to install and bolt into the original mounting holes, and use your existing window channels. Once you install the kit, your window crank becomes the switch. Simply lift up on the crank to roll the window up, and press down on the crank to roll the window down. Made from quality materials like 1018 cold rolled steel, Oilite thrust bearings at the pivot points and treated metal for all the gears makes for a high...

Reproduction master power window switch that goes along with the power window conversion kits. Keep in mind we will buy your old usable factory parts. You might be surprised what those left over clips and wiring harnesses are worth!  Installing this master switch allows you to keep the original look of the crank handles, but allows the driver to control all four windows. All wiring and connectors are included.  ...

This gear was used on Cougars starting in 1969 and then Mustang in 1971. Fits pretty much every (common) Ford power window motor except for the unique "pancake" style motors found with the 1/4 windows on the Cougar and Mustang. Includes metal plate as shown. Replaces Ford part # D0AZ-62234A24. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Aluminum Preheater hose that is used to preheat carburetor air. This 2" X 18" aluminum flex / stretch type hose attaches from the exhaust manifold shroud to the bottom of your air cleaner snorkel.  This hose is sold individually and does not come with clamps.If you prefer, you can grab the cloth type hose here.  ...

Up for grabs is something special for the serious collector of everything Cougar. This is an official press release document with attached 8x10 glossy photo of the 1970 Houndstooth Cougar. These were prepared by the Lincoln Mercury Public Relations Department for immediate release to newspapers in order to spread the word about new and exciting announcements. This particular release features a glossy black and white photo of a woman dressed in a "Swashbuckling Houndstooth Cape" inspired...

Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This is the upper pressure hose, or the pump end only. Lower pressure hose Replaces Ford Part # : D0OZ-3A719-C

Ford part number C9WY-10K843-C Whereas the engineering number printed on the backside of this PCB is the same red vs blue there is a distinct difference. Many people get confused with the numbers printed or cast into parts thinking that that is a part number when really it is a casting number or engineering number and may or may not resemble the actual part number listed in the MPC (Master Parts Catalog). 1969 Standard Cougars used the blue PCB (printed circuit board) up until 2/17/69 and...

Good used PCB that has no burns, corrosion or separating areas. The red PCB (printed circuit board) was used in the latter part of 1969 (from 2/17/69 on) and all of 1970. In 1969 if you had a white plug connected to the PCB it used a red PCB, if you had a black plug the blue PCB was used. Check out the video below on our new gauge tester: ...

Ford part number C9WY-10K843-D Finally! A made in the USA reproduction printed circuit board for your late built 1969 - 1970 Standard Cougar. This is a spot-on, class "A", no excuses reproduction that will give you decades of reliable service. This part exceeds the quality of the originals in that it is made from thicker materials, is bonded better, is more flexible and does not contain formaldehyde as did the originals. This is only for use on the late 1969 Standard white wiring harness...

Ford part number C9WY-10K843-D Finally! A made in the USA reproduction printed circuit board for your late built 1969 XR7 or Eliminator (built after 2/17/69) and all 1970 XR7 and 1970 Eliminator. This is a spot-on, class "A", no excuses reproduction that will give you decades of reliable service. This part exceeds the quality of the originals in that it is made from thicker materials, is bonded better, is more flexible and does not contain formaldehyde as did the originals. This is only for...

Great color brochure showing the full line of Ford products.     ...

This is the jumbo version, a much smaller version is what is commonly found. Mint condition.

Features all the Mercury line-up for 1970. Mint condition, ask us about wholesale pricing or stock trades as we have extras of this promo guide.     ...

This guide is mostly for the Mercury Cyclone GT / Spoiler but has a large two page section of a Yellow Eliminator that includes a "bizarre" shot of it showing it going through a huge mud puddle. Great listing of all the high performance, over the counter packages. Did you know you could buy a "Dominator" kit for your Eliminator? Click on images to enlarge.                           ...

Nice reproduction of the prop rod used on the 1970 Eliminator. This will work on any 1967 - 1973 Cougar that has had a spoiler installed. The pictures of the installed original prop rod were taken at the 2008 PROWL Cougar show hosted by Cascade Cougar Club. The concours correct BOSS 302 Eliminator pictured is owned by John Benoit in Edgewood Washington. Click on images to enlarge. The above picture shows the approximate location of where to drill the hole in the passenger side rear quarter...

This after market adjustable proportioning valve is far superior to the original equipment. Fully adjustable for tuning front to rear brake bias. Requires some routing modifications of brake lines for proper fit. Includes adapter fittings. Replaces Ford part # C5ZZ-2B091-A, or C7OZ-2B091-B.Fits: 1967 Mercury Cougar 1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang 1968 Ford Mustang 1969 Ford Mustang 1970...

1969 and 1970 Mercury Cougar rubber sleeve. Attaches to the front bumper brace tubes. Attaching point is where the side marker wiring harness makes contact with the bumper brace. About 2-3/8 inches long for those wanting to replicate from a piece of thin wall 7/8" ID rubber tubing. Sold individually, two needed per car.

This plastic plate / bracket is installed between dimmer switch and the floor of your 67 - 73 Cougar to provide a bit or protection for the wiring.

Used cast dual sheave alternator pulley. Casting number C9AF-10A352-C, we believe that these originally had a zinc dichromate finish. Called out for use on various 1969-70 Mercury Cougar and Ford Mustang with a need for a dual sheave alternator pulley.*Note - this is a cast pulley instead of the common stamped steel single sheave version.Ford part # C5AZ-10344-L.

Reproduction alternator pulley, single sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Used crank shaft pulley for any 1970 Mercury Cougar or Ford Mustang with Boss 302 engine. This is a double groove pulley with a 5-13/16 inch inner pulley diameter, pulley turns the water pump and alternator. 6-5/8 inches diameter for the smog pump belt. This pulley would have been used without power steering. Also used only up until about Jan, 1970. After Jan 1970, Ford just installed a 3 sheave pulley with the middle sheave not being used. Replaces Ford part number D0ZE-6312-A. ...

Has casting number D0OE-6312-B stamped on the inside. Application for 1970 all 351 engines, 1971 M code 351-4V, and 1971 and 1972 H code 351-2V engines with power steering or idler pulley. Dual sheave crankshaft pulley measurement of 8.00" and 6-11/16" diameters. No air conditioning. Ford Master Part number D0OZ-6A312-E. Four bolts hold it on too.

D0OE-6312-A For both Windsor and Cleveland 351 engines starting in 1970. This is a single sheave pulley, meaning without air conditioning and without power steering. One groove with a diameter of 6-11/16 inches in diameter. Ford Master Part number D0OZ-6A312-A. A four bolt hole crankshaft pulley for use with 1970 and upward crank dampeners.

D0AE-6312-C For both the Cleveland and Windsor variety. Starting in 1970 Ford tried to standardize many of the engine parts. This is the "with air conditioning" pulley for all 1970 - 1971 351-2V & 351C-4V engines, and all 1972 -1973 351-2V engines. Triple sheave 6-23/32", 8.00", 8-13/32" inch diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0AZ-6A312-C. *Excludes 1972 and 1973 Q code 351CJ engines. This means all 1972 and...

D0OE-6312-C For both Cleveland and Windsor 351 engines. This is also the "with air conditioning" pulley, but with power steering option. Triple sheave 8.00", 7-55/64", 6-9/16" diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0OZ-6A312-B. This is a Service Replacement pulley for D0AE-6312-C. *Excludes 1972 Q code 351 Cobra Jet engines. This means all 1972 351C-4V engines.

For 1968 390-2V engines without air conditioning, with dual alternator belts, and with power steering. 1968-69 390-4V, 427 GT-E, or 1968-69-70 428 Cobra Jet engines. All without air conditioning. All with dual alternator belts, and with power steering. Triple sheave 1968-69-70 crank pulley.Ford part # C8AZ-6A312-D, Ford casting # C8AE-6312-D.

C9OZ-6A312-F. Application 1969 and 1970 428CJ all with air conditioning, power steering optional. Ford casting number C9OE-6312-D. Triple sheave 69 70 428 CJ crank pulley.

Applications, 1970 - 1971 - 1972 351c engines, All with or without air conditioning. Casting number D0OR-B. 6-1/4" diameter and 7/16" sheave width.

Applications, 1970 351w engines, 1971 429CJ engines, and 1973 351c engines. All with or without air conditioning. Casting number D0AR-A. 5-3/4" diameter and 7/16" sheave width.

Application, 1967 - 1968 - 1969 - 1970 390 / 428CJ engines with air conditioning. Casting number AF. 5-3/4" diameter and 5/16" sheave width.

Applications various 302 / 351/ 429 engines. All with or without air conditioning. Casting number D0AR-B. 5-13/32" diameter and 7/16" sheave width.Ford part number C9TZ-3A733-D.

Application 1968 - 289-2V, 302-2V, 302-4V, all with manual transmissions and without air conditioning. Also 1968 390-4V and 1968 - 1970 428CJ, all without air conditioning. Pulley diameter 4.75" inches. Ford part number is C8AZ-9B447-B and the engineering number as seen on the front of the pulley is C8AE-9C480-A.

For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. 2 sheaves with a diameter of 5-7/8 inches. This is a good copy of the original water pump pulley, it has no stamped part number.Replaces   C6AZ-8509-A or C6AE-8509-A.

C6AZ-8509-A For use originally on most 289/302/351w/390/428CJ engines with air conditioning from 1967-1970. Thermactor OK on any application. 2 sheaves with a diameter of 5-7/8 inches. Ford casting number C6AE-8509-A. *For year 1967 only > Notes say Prior to 1/9/1967.

Used water pump pulley used on 1970-73 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. This pulley is 5-15/16 inches in diameter. Pulley stamped C9OE-8509-F.

Single sheave pulley 6-61/64 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2-5/16 inches. Applications:1970 Boss 302 Eliminators with power steering**1970 351 with power steering**1971 - 1973 351 engines with power steering or with idler pulley without air conditioning* Ford casting number C9OE-8509-G.  Ford part number C9OZ-8509-D Note:  * The Master Parts...

C8AZ-8509-D 1969 428 Super Cobra Jet only (V and W code axles), 1970 428CJ and 428SCJ prior to Sept 1, 1969. No air conditioning, power steering permissible. Three sheave pulley, 6-1/8 inches and 7-1/8 inches in diameter pulleys. Ford casting number C8AE-8509-C was originally imprinted in ink, if you look closely between the two bonded together pulleys that make this pulley up you may be able to read the C8AE-8509-A stamped casting number from the two sheave inner pulley.

Usually ships in 3-5 business days. Replaces Ford Part #: C4DZ-7653337-A. This is a new part, not a rebuild, no core needed. Correct brackets for a Cougar, not a generic one size fits all application. 5 year warranty when used with automatic transmission fluid.

Used power convertible top pump, motor and reservoir for the Mercury Cougar or Ford Mustang convertible. We do offer an excellent reproduction which you can get right here, but nothing beats original FoMoCo. There is a difference in the space of the mounting bracket between the 1969-70, and 1971-73 Cougar or Mustang convertible top pump assemblies. Not to be interchanged.Our pumps are tested, we recommend flushing the pumps and reservoirs prior to installation. Save your grounding wire,...

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with the 351-2V, 351-4V, and BOSS 302 engines. These are bare pumps, stripped of pulleys, canisters, dipsticks, tags, and brackets. Suitable for core rebuilding. Original pumps would have been numbered HBA-CC. This pump has an off center pressure port on the back. Takes the DOZZ-3A697-B reservoir. *NOTE* Core exchange not required.

Core power steering pump for the Mercury Cougar or Ford Mustang equipped with any V-8 engine. This unit is also for the 1970 Cougar or Mustang equipped with the 428CJ. These are bare pumps, stripped of pulleys, canisters, dip sticks, tags, and brackets. Suitable for core rebuilding. Typically these pumps would have been tagged with numbers which include: HBA-BF, HBA-BF1, HBA-BK, and HBA-BR. *Note - Excludes all 1970 cars with 351 or 302 engines. *NOTE* Core exchange not required. ...

This is a new old stock windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). Replaces Ford Part #: C9AZ-17664-A.

This is a reproduction of a later service replacement version of the windshield washer pump for the 1969 - 1973 Cougar and Mustang (and other Ford / Mercury models). The original Ford part was part number C9AZ-17664-C, which consisted of the pump motor (C9AF-17B616-A) and a retainer (383163-S36), which installs in the 69-70 windshield washer reservoir (C9ZZ-17618-A) or 71-73 windshield washer reservoir (D1TZ-17618-A / D1TZ-17618-B). Replaces Ford Part #: E0AZ-17664-A. ...

Push on retainer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a washer to go against the pinched stops. Probably fits most Ford products, not just 1967-73 Cougar and Mustang.Replaces Ford part number 383358-S.