Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW
Grade "A" will be perfect with no dings, ready to sand and paint. No surprises, just excellent quality!Ford part # D0WB-16A678-A.
This grade "B"unit will only have a minor ding like the one shown here.Ford part # D0WB-16A678.
New Old Stock grille center extension / surround for the 1970 Mercury Cougar, in the original box from Ford.Ford part # D0WB-16A678-A.
Driver side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Driver side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530057-A.
Passenger side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Passenger side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530056-A.
Ford original eye let bushing 100% correct for the 67-69 Cougar without competition handling, but will fit on any 67-73 cat including those with competition handling. Ford Part #: C4DZ-5781-C.
Poly eyelet bushing that will fit any 1967 through 1973 Mercury Cougar. Replaces Ford Part #: C4DZ-5781-C.
This eyelet bushing is made from higher grade rubber and unlike the NOS and other reproductions has a solid center shaft. The center shaft of this reproduction is a flat piece of steel that is bent into a circle to make the shaft for the eyelet bolt to go through, just like NOS. Two per car, these are used on one end of the leaf springs and the shackles are used at the other end. Replaces Ford Part #: C7WY-5781-A, C4DZ-5781-C, C5ZZ-5781-A, D3ZZ-5781-B. ...
New clear plastic lens or face plate for the heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!
New clear plastic lens or face plate for the A/C and heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!
This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. 1967 AM-FM radios would use this part as they did not have a balance feature. Called a "Sleeve" 1969-70 Cougar and Mustang AM radios use this sleeve. Also found on various 1970-76 Ford and Mercury cars...
Rare option that makes your inner right hand radio knob work as fader. Very limited supply, guaranteed to work. New Old Stock switch. Ford part number C7AZ-18972-A and C7AA-18972-A on the wiring tag. NOS
Rare option that makes your inner right hand radio knob work as fader. Very limited supply, guaranteed to work.
White reproduction fan for the Thermactor Smog Pump.
This is an excellent reproduction made from the original Ford tooling and features the original Ford logo and part number. This is for the 20" radiator used only in 1970. It weighs 1.82 pounds which is slightly heavier than the one sold Ford when they went obsolete in the mid 1990's. Replaces Ford part # D0ZZ-8146-B. 21" center to center mounting width12" center to center top to bottom mount Overall height 19" For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check...
Replaces Ford part # C8ZZ-8146-A. This is a good reproduction made from the original Ford tooling but does not have the original part number or FoMoCo lettering. Has a smooth texture (unlike original) but it is made from a more durable plastic material. This is for the 24" radiator only. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...
This is a good reproduction made from the original Ford tooling and features the original Ford logo. This is for the 24" radiator used in both the 351 Windsor and 351 Cleveland in 1970 only. Made of a different material than original and is 1.76 pounds VS. 2.56 pounds on the NOS shroud. *NOTE* This has the BARNUM BROS. FIBRE CO. INC. scratched off (but still faintly visible) just like our NOS shroud. Replaces Ford part # D0ZZ-8146-A. For some helpful tips on upgrading your Cougar (or Mustang)...
This USED shroud was discontinued by Ford in the mid 1990's. It really is no different in appearance from our reproduction, but it does weigh a hefty 2.56 pounds and the reproduction weighs 1.76 pounds. Must have FoMoCo / part numbered shroud for that show quality BOSS 302 or 351C Eliminator. Just like our reproduction, the BARNUM BROS. lettering has been ground off. This was done because Barnum no longer made the shrouds for Ford in the latter years, but the tooling still had their name on...
Fan shroud installation kit for 67 - 71 Cougars and Mustangs. Will fit 1971 Cobra Jet shrouds.
Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.
Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.
Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.
Fan spacer, measuring 1-1/4 inches, but referenced at 1-9/32" too. Application includes 1971 - 1973 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-20, cross reference to C8YE-8546-A spacer.Ford part # D1OA-8546-AA, Ford engineering # C8YZ-8546-A.
Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.
Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.
Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.
Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.
Metal fan wheel or squirrel cage for any 1969-70 Mercury Cougar or Ford Mustang with heater only. Dimensions 4-3/4 inches in diameter and 2-1/2 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.
Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.
Self threading white plastic. Used on front and rear valances.Sold individually.
Reproduction alternator mounting kit for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Spacer not included, but available.
Contains nut and washer. Fits all Ford alternators. AMK F-644.
Bolts, washers, and spacers kit for installing the rear bumper brackets on any 1969-70 Mercury Cougar or Ford Mustang.
Sold as a Kit as Pictured.
AMK engine fastener kit for 1971 Mercury Cougar and Ford Mustang with J or C code 429 Cobra Jet engines. This kit claims to have 136 pieces. This kit additionally fits 1970-71 Ford Torino and Mercury Cyclone and other variants with 429CJ engine.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake...
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Fits Standard and XR7 Sold as a Kit as Pictured.
Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang
Fits Standard and XR7 with front bumper guards.
Fits standard and XR7 Sold as a Kit as Pictured. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! ...
This reproduction hood latch and catch screw and U nut kit fits both the Standard and XR7 and is sold as a kit as pictured.
This reproduction hood latch vertical support screw and U nut kit fits both the Standard and XR7 and is s sold as a kit as pictured.
This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.
Fits Standard and XR7