1970 Mercury Cougar

For the purists out there we have a very limited amount of used visors that have no impressions, seam separation and minimal rust on the clips if any. Convertible and Coupe are the same.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

Used Driver Side Grade "A" Center Grille Support for the 1970 Mercury Cougar

Used Driver Side Grade "B" Center Grille Support for the 1970 Mercury Cougar

Used Passenger Side Grade "A" Center Grille Support for the 1970 Mercury Cougar

Used Passenger Side Grade "B" Center Grille Support for the 1970 Mercury Cougar

Support brace between the cowl top and the brake pedal support bracket. Fits 1969-70 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Ford part number C9ZB-6501554.

Support brace between the cowl and the top of the brake pedal support bracket. Fits 1970 Mercury Cougar and Ford Mustang with either automatic or manual transmissions, drum or disc brakes. Overall width is right at 5-1/2 inches on the 1970, larger than the 1969 version. Ford part number D0ZB-65015A18-A.

This tubular support gives rigidity to your hood extension which houses your center grille. These are hard to find with no bends or cracks due to the fact that the 1970 hood protrudes in the center.1 required per car.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint and unused condition. Ford part # D0ZZ-6501508-A. *NOTE* Manual brake supports are different. Manual brake supports have four threaded nuts swedged to the...

D0ZZ-6501508-B This is the correct hanger for a 1970 Mercury Cougar or Ford Mustang with power disc brakes. If you have a manual transmission car with worn out clutch bushings this is a great replacement part for you as it will have been removed from an automatic transmission equipped car which means the clutch bushings will be in mint, unused condition. Ford master part number D0ZZ-6501508-B for power disc brakes. *Note - Power brake and manual brake supports are different. Power brake...

Reproduction brake pedal hanger also known as brake pedal support for Mercury Cougar and Ford Mustang.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.

Fills the hole in the core support where the A/C lines pass through to the condenser. Replaces part # C9ZZ-19819.

Pair of reproduction cowl vent panel support pads.

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the spring that holds the rear license plate or fuel door in the upright position. Fits 1969-70 Cougar.Ford Part #: C9WY-13455-A

Good aluminum piece that has no corrosion, no dings and all six mounting studs will be firmly in place. This same bezel was used on all Standard, XR7 or Eliminator Cougars for 1969 and 1970. Obviously the clock hole was not utilized on the Standard Cougar.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

D0ZZ-5482-B Factory used front sway bar found on most 1970 Cougars. 3/4 inch in diameter. This factory used front sway bar, does not include mounting anybrackets or end link kits.

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This A/C thermostat is made by the original supplier and stops the evaporator coil from freezing up. Replaces Ford part #: C7ZZ-19618-A and D1ZZ-19618-A.

Used air conditioning thermostat switch for any 69-70 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part number C9ZA-19618-A

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

D0AZ-2B264-A Identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems.

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

New Old Stock 1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was used and the surrounding bezel would be labeled "Top" or "Defog" in the farthest position to the right. The fourth switch is never used on the 1969 xr7, it is just there to...

1969-70 Mercury Cougar XR7 dash 3 pin on / off rocker switch. Suitable for any position, MAP COURTESY PANEL or ACCY. Switches sold pit free on the chrome. Switches guaranteed to work, but are likely stiff. Electro solvent usually helps with that sticking condition, see product label for directions prior to use. These are sold individually and in most applications four are used except in 1970 xr7 convertibles or or 1970 xr7 coupes with rear defog. In these cases a different design of switch was...

C9WY-14018-B Left side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

C9WY-14018-A Right side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7 Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

This is a tested original FoMoCo headlight switch that will work, there is no warranty. The primary reason we list these old used switches is that some people are missing their switch altogether and need the beveled cup shaped spacer that mates to the dash. As pointed out in our listing for the reproduction headlight switch, the spacer is not included with our new units. Ford part # D0WB-11652.

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

C9ZZ-18578-A mounts to the rear of the factory installed heater control ventilation control pane. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing the 1969-73 selector button kit. LINK This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...