1967 Ford Mustang

C7OE-9431-A Factory original cast iron exhaust manifold for driver side. 1967, 1968, and 1969 390/427 left side manifold remained unchanged for all three years. Includes 1968 X code 390-2V Premium fuel cars. Click on images to enlarge. ...

Factory original cast iron exhaust manifold for the passenger/right side and is probably a mid-year change for 1967. For both S & X code 390 engines and W code 427 GT-E engines up until 2/15/1968. Butterfly spacer not included. Ford part # C7OE-9430-C.

C6OE-9428-A 390-4V factory original cast iron exhaust manifold for passenger side. Even though the photo shows a chamfer where an exhaust donut would go, the proper 1967 manifold would have been cast flush, and a butterfly spacer would have been used. The spacer had a flapper that partially blocked the pipe and allow heat to be dissipated upwards to the choke. Spacers not included. We suggest purchasing the later version of manifold that did not use the spacer. *Note, a spacer may be needed if...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. The pictures show an example of how it looks once installed. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. Also found on various 1976-70 Ford and Mercury cars such as Galaxie, Fairlane, Torino, Ranchero, Falcon, Montego, and Thunderbird. The knobs...

Used original fan shroud for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. Shround will have minor damage as shown. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. Ford part # C9OZ-8146-A For some helpful tips on upgrading your Cougar (or Mustang) cooling...

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer.Ford part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-39/64 inches and sometimes mentioned as 1.61". Reference number YA-71.Ford part # C8DE-8546-A, Ford engineering number C2OZ-8546-G.

Fan spacer, measuring 1-7/8 inches or sometimes mentioned as 1.88". Application includes 1970 Mercury Cougar and Ford Mustang with 428CJ engines. Reference number YA-81.Ford part # C8AE-8546-C, Ford engineering # C6OZ-8546-D.

Fan spacer, measuring 2-1/8 inches. Application includes 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Reference number YA-83.Ford part # C8SE-8546-B, Ford engineering # C8SZ-8546-D.

New replacement J-nut or they are sometimes called U-nuts. These clip into those square holes in the fender aprons for fastening the fenders on 1967-70 Mercury Cougar and Ford Mustangs. These clips are 5/8 inches from the hole center to folded edge. We also see the same clips with 27/32 inch spacing for fender mounting. Numerous other uses, we find this clip on the hidden headlight buckets on 1967-68 Cougar and XR7's.

Set of nuts and Ferrules for thermactor smog tubes on any 1967 S code 390, 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original or reproduction smog tubes. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the smog tubes and other hardware.

Tall style filter for C4 transmissions.  Fits all Ford C4 transmissions for any 1966-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. This is designated as the 'tall' filter, introduced in 1965. I guess that Ford installed a deeper pan in 1965? Solid metal construction with filter inside.

Replacement transmission pan filter and pan gasket kit. Gasket for the C4 (W Code) transmission. Replaces Ford Part Number: C5ZZ-7A098

Used service replacement, black plastic filter retainer for the Mercury Cougar, Ford Mustang and other Fords equipped with Midland Booster. It fits between the master cylinder and brake booster on the aluminum master cylinder spacer. The repro and service replacement filter covers are usually black not white.You can find the filter here. ...

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Quality built new automatic transmission flex plate for all 1967-68 Mercury Cougar and Ford Mustang with 289/302 engines and C-4 automatic transmissions. Looks identical to the OEM Ford plates, has new starter ring installed. Has the correct 28oz. weight for vintage 289/302 engines. The 5.0 liter engines used a 50oz. imbalance.

Brand new flex plate for all 1967-69 Mercury Cougar and Ford Mustang with any of the 390 engines. Also includes 1968 Cougar GT-E with 427-4V engines. Comes complete with new starter ring gear installed as shown. Neutral balance, meaning this has zero weights attached. *Note - Will not work on 428CJ engines.

New manufactured flywheel for manual transmissions. Fits all 1967-68 Mercury Cougar and Ford Mustang with 289 engines with 3 or 4 speed manual transmissions. This flywheel has a 157 tooth ring gear. This flywheel will fit many other Ford small block V-8's with the 157 tooth gear.*Note - Most 1968 and newer Cougars came with 164 tooth flywheels, and they are not compatible.

NOS Ford Ready Reference Parts and Accessories Catalog for 1962 - 1967 Ford vehicle models including Mustang, Fairlane, Falcon, Thunderbird, Ranchero and other various full sized Ford cars. Filed with helpful information about maintenance, diagnosis, testing and other procedures pertaining to a wide variety of subjects. You can find information on wheels and bearings, brakes, axle and driveline, suspension, engine, transmission, cooling, fuel systems, electrical and tons more.This catalog...

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Reproduction Front end rebuild kit specifically for the 1967 Cougar with articulated strut rod arms. There are a lot of choices out there when it comes to front end parts. There are numerous manufacturers on each part and some are priced very, very low. We do not like the quality of many of these discount parts and do not like selling them when we don't like using them on our own cars. We feel we can stand behind these quality products shown here. Note: Bright orange protective covers are to...

New Old Stock NOS retainers for right and left front marker / parking lights for any 1967-68 Mercury Cougar or 1965-1968 Ford Mustang. These are driver and passenger side specific. Replaces Ford part # C5ZZ-13221-C*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Used vented fuel, or gas cap as installed on 1967-69 Mercury Cougar and 1970 cars without California emissions. Also fits 1969-70 Shelby Mustang. In 1970 California required a non-vented fuel cap. This version does have a check valve, one way vented. This is probably a service replacement fuel cap. Typically, OEM factory caps only said "VENTED", see our related item for that specific gas cap.We stock these in limited quantities, and will have an intact paper gasket. "ANTI SURGE"...

Quality U.S.A. made hose with concours repeating GAS markings. Also include OEM mounting hardware. Replaces Ford Part #: C7ZZ-9327-A. Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction fuel line that goes from the fuel pump to the carburetor made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 390-4V engine. Fits all FE engines with Holley 4150, as long as they do not have the Carter "X" fuel pump. Carter X fuel pumps are not crimped together.

Reproduction fuel bowl fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All steel fitting, two needed per carburetor. Sold individually. Check the threads in those Holley bowls prior to installation, often times the bowls are bad.

Reproduction fuel pump for all 1967-70 Mercury Cougars and Ford Mustangs equipped with the 289, 302 or 351W engines. Be aware that this pump has a 3/8 inch fitting for the fuel line.

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1967 Mercury Standard model Cougars and all Ford Mustangs with 16 gallon fuel tanks. This is an original 1967 fuel sending unit with one electrical prong. Ford casting number C7ZF-9275-C. This unit comes with a new 5/16 inch filter, brass float, and sending unit gasket. The only difference between this sending unit and the 1968 sending unit is the diameter of the pickup tube. The 1968 verison of this...

Premium reproduction fuel / gas tank for the Mercury Cougar or Ford Mustang. 16 gallon capacity, correct in every way including the drain cock.Replaces Ford part # C5ZZ-9002. Check out our video on replacing the fuel system on a '68 Cougar! ...

If you find that this tube has too small of fittings for your OEM 4150 / 4160 Holley carburetor than what has happened is that someone has replaced your transfer tube and fittings with one of the after-market kits available at speed shops. This is the ONLY correct transfer tube for a Cougar equipped with a Holley from 1967 - 1970.  Ford part # C9AZ-9H576-A.

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

1967-1973 14 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for courtesy, instrument cluster, door, map, glove box, pillar, luggage compartment, and clock lamps. Also for the lighter, ignition key on and head lamp on buzzers.

Reproduction Glove Box Catch for the 1967 and 1968 Mercury Cougar and Ford Mustang

New old stock 1968 glove box lock. A great optional accessory. All original glove box latches. Includes 2 matching aluminum keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Ford part number C6OZ-6206081-C. Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges. 

NOS grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. New from Ford. Replaces Ford part # B5A-1131-A.

Economy reproduction sponge foam grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. * Note - Used starting during the early part of 1969. Compare the evaporator line orientation for both years.

Reproduction 3/8" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.Replaces Ford part # C7ZZ-9288.

Original two piece assembly that bolts to the passenger side of your firewall on A/C equipped Cougar's. Comes as taken from parts car. If you own a 1969 Cougar you will need to look at the configuration of the evaporator lines. During the 1969 model year this grommet bracket changed to reflect the running year change. It will look like the 1970 pictured bracket.Ford part # C7ZA-19B589-A.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.Ford Part # 380699-S

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

High quality, durable canvas cap with velcro closure. The hat now features our Web address on the back! "The baseball cap arrived Saturday but since I wasn't home, they didn't leave it for me. I picked it up today at the post office. It's real nice! Seems to be a higher quality cap compared to others I've worn. Thanks for sending it." Larry Check out this video of our 2013 Open House event! ...

Reproduction headliner in parchment color found on Mustangs, which is a darker tan color. Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge.