1967 Ford Mustang

NOS C7ZB-6522448-A Passenger side small size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.

Made from fuel resistant cork like original.  Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...

Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.

This gasket goes between the rear axle flange and the backing plate on the differential. It fits all Mustangs from 1967 - 1970.

Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.

Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.

Gasket for mounting the oil filter adapter to any FE or Ford 360, 390, 410, 427, 428CJ engine. Name brand gasket, fits all 1967-70 Mercury Cougar or Ford Mustang with S, X, R, Q, or W code engines.

OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

Rubber Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.

New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.

Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.

Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.

New water pump plate gasket for the Mercury Cougar or Ford Mustang.

New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.

New water pump gasket for 1967-69 Mercury Cougar and Ford Mustang with 289/302/351W. Single gasket for sealing water pump to water pump plate only.

Made from durable black plastic with correct ridged edges. Includes all four gaskets, enough for both the left and right exterior door handles. Replaces Ford part numbers C7ZZ-6522428/9.

If you're going to rebuild your engine, this is the item you'll want to get. It's the complete gasket set for your 289 and 302 engines. (Will not fit early Boss engines). Included in this kit are the following: Head Gaskets Intake GasketsOil Pan Gasket Rear Main SealExhaust Manifold Gaskets Valve Cover Gaskets Water Pump GasketsTiming Cover Gaskets Timing Cover SealWater Neck GasketFuel Pump GasketDistributor Gasket ...

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1967-70 big block Ford engines with size 390, 427, or 428 cubic inches, FE engine only. 1967-70 Mercury Cougar, Ford and Ford Mustang.

New timing cover gasket set for 1967-70 Mercury Cougar and most all Fords with 289/302/351W engines. Gasket set includes; timing cover gasket, crankshaft seal, water pump gasket for early or late water pumps, and the oil pan corner gaskets under the timing cover.

New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.

Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Rubber valve cover gaskets for any FE 390 or 428 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.

NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...

C7ZZ-65222A89-A Mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Driver side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21547-A.

C7ZZ-65222A88-A Mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A.

Insert to replace the worn rubber and felt channel guide for the door glass in your cool Cat or precious Pony. These units feature original looking felt. Top molded pieces are bonded securely and has steel inserts for added strength. Sold in a pair. There are three brands of this particular piece, we carry the best even though our price is less than most everyone else. Replaces Ford part #C7ZZ-6521546-A and C7ZZ-6521547-A. Check out our handy diagram below to find other '67-'68 door parts you...

This reproduction tape is a must for anyone replacing their stainless steel window trim pieces on the 1967 - 1968 Cougar or Mustang. Can be used on any of the side windows. We suggest saving the original quarter window rubber surround if possible, due to the curves, but this tape can be used there as well if needed. This glass setting tape is designed to look and perform similarly to the original Ford factory material. It creates a water tight bond as well as...

1967-1968 15 amp Buss style glass tube fuses sold in a package of 5 and used for the turn signals. This fuse is not located in the fuse box, but rather in an in-line fuse holder coming off of the turn signal switch on the steering column about 2.5 inches down after the plug.

1967-1970 7.5 amp Buss style glass tube fuses sold in a package of 5 and used for courtesy, glove box, luggage compartment, clock, tachometer, and radio pilot lights. Fuse length 7/8"

Early 1967 style glove box catch. Fits all 1967-68 Cougars and 1966-68 Mustangs.Replaces Ford part number C6OZ-6206064-A.

Used glove box catch for any 1967-68 Mercury Cougar or Ford Mustang. Several versions of this catch were used 1967-68, this is the most common version. Replaces Ford part number C6OZ-6206064-A.

Fits either 1967 or 1968 Mercury Cougar or Ford Mustang. Technically this is a copy of the 1967 factory installed version. 1968 factory glove box liners have a smooth section for installing the tire pressure decal. See the related items for 1967 and 1968 good used liners. Replaces Ford part #: C7ZZ-6506010-A.

Used glove box liner or plastic box for any 1967 Mercury Cougar or Ford Mustang. This is the same as the Scott Drake reproduction, but it lacks the smooth section for the tire pressure decal which was introduced on the 1968 cars. Used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange, Replaces Ford part number C7ZB-6506010-A.

Used glove box liner or plastic box for any 1968 Mercury Cougar or Ford Mustang these do have the flat smooth area for installing the tire pressure decal. This is nearly the same as the 1967 used and Scott Drake reproduction, which lack the smooth section for the tire pressure decal. Good used part with no cracks or heavy scratches. Inside clip usually has light rust. 1967 and 1968 glove box liners fully interchange.Replaces Ford part number C8ZB-6506010-A.

A great optional accessory. All new tooling was created to produce these glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Replace Ford Part #: C6DZ-6506072.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges.

A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1967, notice the push button with square edge? 1968 push buttons had rounded edges. See related for reproduction and 1968 used.

A great optional accessory. All original glove box latches. Includes 2 matching keys. Fits any 1967-68 Mercury Cougar or Ford Mustang.Technically the lock style is for 1968, notice the push button with rounded edges? 1967 push buttons had square edges. See related for reproduction and 1967 used.

Reproduction grease cap for front wheels of the Mercury Cougar or Ford Mustang. 2 Required per car, sold individually. Replaces Ford part # B5A-1131.

This is a front brake grease dust cap tool. No more dented caps. These are milled from 6061 solid aluminum.

Good used grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. This part will not have any missing "chunks" but will show hairline cracks most evident where the heater core tubes pass through. The engineering number imprinted on the back side of this grommet taken from a 1967 Cougar is C7ZA-19B588-A. Good through mid year 1969. Compare to the 1970 item pictured for selection on your late 1969 Cougar.Please indicate in the Order Notes...

Premium reproduction rubber grommet that seals the heater hoses and A/C lines where they pass through the firewall on the passenger side. Molded rubber exactly like the original! Other reproductions on the market are die cut from sponge rubber sheets and nothing like the original. * Note - Used starting during the early part of 1969. Compare the evaporator line orientation for both years. ...

Reproduction rubber grommet for the air conditioning case. This grommet encloses the tubes for the evaporator, and slides into a slot on the heater box. Fits 1967-1969 Mercury Cougar and Ford Mustang. 1969 owners, please compare your grommet to the picture, late 1969 changed to a triangle shaped grommet. Please see related items for late 1969-73 rubber grommet. Replaces Ford part number C7ZZ-19B552-A. Check out our videos below on how to replace a heater core! We now have separate videos for...

Brake line rubber grommets for any 1967-73 Mercury Cougar or Ford Mustang. These are the ones that go through the shock towers for the front brake lines. Drum or disc, all the same. Sold as a PAIR. Ford number 373624-S.

Reproduction grommet that seals the check valve to the Midland brake booster on the 67 - 68 Cougar or Mustang. We also sell the grommet / check valve combo, you can find it here.

Reproduction 3/4" fuel line to side apron grommet for the Mercury Cougar or Ford Mustang.