1967 Ford Mustang

Reproduction rear boot for your 67 - 69 Cougar or Mustang Midland power brake booster.

Replaces Ford Part #: 379670-s

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

Reproduction front diaphragm for your 67 - 69 Cougar or Mustang Midland power brake booster.Diameter 7 1/4"

[No Description Provided]

Passenger side rear brake cable bracket. This is a part cut from a car, some trimming and or spot welds will need to be removed prior to installation. Fits all 1967-69 Mercury Cougar and Ford Mustang.

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

This is the seal at the back of the booster on the Midland-Ross units.

Since at least 2 speakers (channels) are required for stereo radios, this speaker system has been developed for classic vehicles that came with only one mono speaker. These dual voice coil "DVC" speakers will give you the best possible sound from your original speaker location. DVC speakers have up to 70% more cone area than the conventional dual speaker assemblies giving you improved bass response and 140 watt power handling. Both stereo channels connect directly to one speaker with dual...

6x9 Replacement for OEM package tray speaker. Comes pre-wired with the stock style pigtail to plug in to your original wiring. Sold individually, 2 required per car.

Kit includes one pair of 25 watt speakers (50 watts total peak) with correct pigtails and one pair of correct speaker grills with the exact screen pattern as original. Correct mount spacing utilizes the factory holes in your package tray, hardware included. This kit is 100% correct for the 1967 or 1968, but will work on the 69 or 70 as well. The Cougar package trays for the 69 and 70 came perforated from the factory for speakers, so the grills are not necessary. Thanks for the plug Mark!: "My...

Very good reproduction of the speaker grille located on the package tray in the 1967-68 Mercury Cougar and 1965-70 Ford Mustang. Includes the mounting hardware.  Sold individually.

Unlike the originals, the housing on this unit is hard plastic, not vinyl. The day / night function does not work well on this Chinese unit. Since we tell you up front that this is a substandard part that you will not be happy with, we will not accept returns. Keep in mind this is the EXACT mirror marketed by other vendors as "Good Quality". When you see this icon on a product, it means it's a sub-par item that we don't recommend, due to our own experience in handling and using this item on...

Black grade A mirror assembly with re-silvered lens. This is the early rubber version that is big and bulky with a twist knob for the day / night feature. Found on early 1967 cars, later cars used a smaller mirror with either a twist or lever for the 'Day/Night' function. We also sell re-silvered lenses by themselves on an exchange basis. Sold outright, no core required.  In our observations 1967 Mercury Cougar XR7's were all black colored. Ford documentation lists possible part numbers...

Dark Ivy Gold / Dark Green grade A mirror assembly with re-silvered lens. This is the early rubber version that is big and bulky with a twist knob for the day / night feature. Found on early 1967 cars, later cars used a smaller mirror with either a twist or lever for the 'Day/Night' function. We also sell re-silvered lenses by themselves on an exchange basis. Sold outright, no core required.  In our observations 1967 Mercury Cougar XR7's were all black colored. Ford documentation...

This is a grade 'A' used mirror assembly with no UV damage and has had the mirror lens "re-silvered". Keep in mind a restored lens that is decades old will look good when finished but almost never flawless as the surface of the glass will usually have light scratches and often faint spotting on the backside from previous water damage / staining. Sold outright, no core required.  NOTE: Pictured is black, but if you would like a specific color other than black please mention it in the...

NOS service replacement flip style rear view mirror assembly. Lens shows some staining from years of being on the shelf . See reference photos above. In our observations 1967 Mercury Cougar XR7's were all black colored. Ford documentation lists possible part numbers of C7AB-17702 and service replacement box shows C7AZ-17700-F1A. This picture below shows the rear view mirror variations from 1967-1973. Check out this video ...

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. These rear view mirror lenses are sold on an exchange basis.  Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind...

Restored rear view mirror lens for the Mercury Cougar or Ford Mustang. Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard.  We STRONGLY suggest you watch our "how to" video prior to attempting to remove your lens and send it in. Keep in mind glass is porous and is prone to staining. Often times these faint stains do not show up until...

New disc brake proportioning valve / distribution block seal and rebuild kit for the Mercury Cougar or Ford Mustang / Torino. Every 1967-69 Cougar, Cyclone, Torino, Ranchero and Mustang equipped with disc brakes needs this kit even if you are not leaking fluid yet. These little "O" rings are always "rock hard" after 40 plus years because the original O-rings are composed of a BASIC nitrile compound. After several years, the absorption of brake fluid will change the molecular structure of the...

Kit for rebuilding your drum brake distribution block on your Mercury Cougar or Ford Mustang. Special square O-rings are made from EPDM (Ethylene Propylene 70 Durometer) which is specifically designed to withstand chemical degradation caused by prolonged exposure to brake fluid.*Customer Feekback*"You guys are awesome, I couldn't find a rebuild kit for my Galaxie's brake distribution block anywhere else! Thank you!" Henry M.Check out this video ...

This all inclusive vacuum booster master rebuild kit is great for the do it yourself-er or the person that would like to retain their original case / housing. Also a great option for the out of country customer that does not want to pay expensive shipping to return a core. Keep in mind this will only work on a BENDIX unit with the crimped band. Also be aware that our rebuilt units we sell do not have 100% new parts as shown here as our builder will reuse multiple parts that can be cleaned up...

Basic C4 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C4 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that W code C-4 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Basic C6 transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford C6 transmissions for any 1967-73 Mercury Cougar or Ford Mustang with that U code C-6 transmission. Quality kit, same as supplied to professional shops. Big and small block C6's.

Basic kit for rebuilding your Ford Autolite or Motorcraft square bore 4300 or 4 barrel carburetor. This kit is not for later spreadbore carburetors. Spreadbore carburetors have much larger secondary venturis. See picture.

Most complete kit available for rebuilding the early 1967 Mercury Cougar or Ford Mustang power steering control valve. Includes a very accurate sleeve, all 4 seats, and various seals and hardware. Please note that the early 1967 control valves did have 1/4 inch lines. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #:...

Most complete kit available for rebuilding the late 1967-70 Mercury Cougar or Ford Mustang power steering control valve. Includes a very accurate sleeve, all 4 seats, and various seals and hardware. Please note that the early 1967 control valves did have 1/4 inch lines. Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #:...

Great kit for those that have a good used power steering control valve unit to rebuild.  Keep in mind many of the high mile control valves in circulation are worn beyond factory tolerances and are not easily rebuilt. Our re-manufactured units are a great solution if this is the case. Replaces Ford Part #: C2AZ-3A533-A.

Basic FMX transmission rebuild kit. Kit includes gaskets, seals, bands, filter, modulator, everything as shown. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. Quality kit, same as supplied to professional shops. 

This all inclusive vacuum booster master rebuild kit is great for the do it yourself-er or the person that would like to retain their original case / housing. Also a great option for the out of country customer that does not want to pay expensive shipping to return a core. Keep in mind this will only work on a MIDLAND unit with the removable band. Also be aware that our rebuilt units we sell do not have 100% new parts as shown here as our builder will reuse multiple parts that can be cleaned...

If your 4 speed shifter is broken or wobbly, it's probably time to rebuild it. This kit, when installed, is used to keep tension on the shifter where it connects to the shift linkage, and onto the transmission. Includes insulators, springs, trunions and bolts. Check out our video on rebuilding your shifter below: ...

Air conditioning bearing replacement service. Send your wide bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new wide bearing. Price includes new bearing (long or short shaft) and labor, shipping extra.  * Note * There are several pulleys that we are unable to press apart. Please check photos for examples of the known pulleys that we can assemble, but not disassemble. *NOTE* Excludes certain 1968 pulleys with stamped...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Our service is to rebuild your sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980 Ford / Mercury / Lincoln sending units accepted. See our related listing for non-low fuel sending unit rebuilding. A...

This option requires that you send your core in advance. Your core gets rebuilt and returned. If you don't have a core, WCCC has come across a few from our wrecking yard, give us a call to discuss details. Be aware that the OEM Ford 1967 sending units had 5/16 inch tubes for the filter, 1968 had 3/8 inch tubes.Our service is to rebuild your standard fuel sending unit. A quality core is required. Yes, we can rebuild other than 1967-73 Mercury Cougar and Ford Mustang sending units. 1967-1980...

Basic kit for rebuilding a 1967-70 Holley model 4150 4 barrel carburetor. Includes illustrated instructions. Holley packaged renew kit. This kit is not for model 4160 or other Holley carburetors. See pictures of Holley 4150 below. Click on images to enlarge. ...

This receptacle was used on the 1967-68 rear of all consoles except the 1967 standard. It was also used in the rear interior panels of the 1971 - 1973 Cougar for both convertible and coupe. Not correct for 1969 - 1970 convertible rear side panels.Ford part number C5AZ-6230702-A.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

This area of the door often cracks due to the stress caused by worn out hinges. This twelve piece kit includes six screws and six form fitting washers to reinforce the recessed areas that often crack. If your latch area is badly cracked you will want to purchase the repair kit that requires being welded in.

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

Used flexplate reinforcing ring, Ford called it a fly wheel reinforcing plate. Fits all Ford small block engines including 260, 289, 302, 351W and 351C. Strengthens the area where the automatic transmission flex plate mounts to the crankshaft. This is not just a ring with 6 holes in it, it is indexed specifically for the flex plate and only goes on one specific way. It has to be indexed because of the weight on the flex plate. Just under 4 inches in diameter. Special bolts not included, but...