Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1201-1248 of 3185
$0 Price: $72.75

Buy Details

Availability: In-Stock Item
Item #: 41507 -

This reproduction heater blower switch for Mercury Cougar and Ford Mustang mounts to the rear of the factory installed air conditioning ventilation control panel.Replaces part # C7ZZ-19986-A.

$0 Price: $413.85

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 47896 -

Usually ships in 3-5 business days. Reproduction heater box with A/C for 67 - 68 Cougars and Mustangs. This new plenum is made of a sturdy hard plastic that should hold up much better than the original fiberglass boxes. Includes pre-installed seals, clips, flaps, brackets, etc. Just install your heater core (with end cap seals) and AC evaporator (with rubber grommet). See related products. The style of this box most resembles the 1967 version, with the flat mating surfaces between the two...

$0 Price: $260.05

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 41955 -

Heater Box Assembly for 1967-1968 Mustangs without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a factory type fiberglass two piece heater box/heater core casing. The heater box is a pre-assembled unit which includes the gasket and all seals. The heater plenum attaches to this assembly and directs warm air to the car. Check out our video below on how to replace a heater core! We used a '69 Cougar with A/C, but many of the same concepts...

$0 Price: $195.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0139 -

Used Heater Box Assembly for 1967-1968 Mercury Cougar and 1965-68 Ford Mustang without air conditioning. The heater box assembly consists of the front and rear casings with doors. This is a used factory fiberglass two piece heater box/heater core casing. We suggest purchasing the foam kit and new heater core. These used boxes are over 45 years old, there will likely be some cosmetic issues, which include minor cracks or chipped fiberglass. Clips to hold two pieces together are included. *Note...

MSRP:$2.50
$2.50 Price: $1.26

Buy Details

Availability: In-Stock Item
Item #: 12280 -

Special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

$0 Price: $3.38

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0372 -

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws. ...

$0 Price: $3.38

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0019 -

Special steel clamps that hold both halves of the heater box together on both A/C and non A/C Cougars and Mustangs. Two versions found, round and flat, like in the comparison with reproduction. Sold individually. This taller or round clip is slightly easier to clip onto the boxes. Replaces part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard...

$2.50 Price: $5.27

Buy Details

Availability: In-Stock Item
Item #: 26197 -

Set of 4 special steel clamps that hold both halves of the heater box together. Fully functional, but is different than the original. Replaces Ford Part #: C0DF-19A779-A. *NOTE* Never pry these off or the lip they attach to will lose the edge and it will be hard to fasten the clips back in place. They are designed to come off by inserting a standard screw driver in one of the ends and flexing the clamp to open the jaws.

$0 Price: $18.15

Buy Details

Availability: In-Stock Item
Item #: 14363 -

Reproduction heater cable for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit is an exact fit!Replaces part # C7ZZ-19988-A.

$0 Price: $112.35

Buy Details

Availability: In-Stock Item
Item #: 25984 -

Constructed from corrosion resistant copper and brass. Quality replacement part for a job you do not have to do again anytime soon. Replaces Ford Part #: C9ZZ-18476-B. Check out our videos below on how to replace a heater core! We now have separate videos for the first generation ('67-'68) and second generation ('69-'70). ...

$0 Price: $112.35

Buy Details

Availability: In-Stock Item
Item #: 25987 -

Constructed from corrosion resistant copper and brass. A great buy for anyone needing to make repairs to this vital part. Replaces Ford Part #: C5DZ-18476-A. Check out our video below on how to replace a heater core! We used a '69 Cougar with AC, but many of the same concepts apply to other years. ...

$0 Price: $16.22

Buy Details

Availability: In-Stock Item
Item #: 10534 -

These reproduction pieces are factory correct replacements for your 1967-68 Cougar or Mustang and will only fit non A/C heater cores of those years.

$0 Price: $74.55

Buy Details

Availability: In-Stock Item
Item #: 26155 -

Concours correct white striped heater hose for 1967 and early (prior to 2/1/1968) 1968 Mercury Cougar and Ford Mustang with factory or integral A/C. Durable white striping with no mention of "Autolite" - this particular hose did not come with that marking. The 'with air conditioning' hoses have correctly molded 90 degree elbows that fit on the water valve side. Some length trimming may be needed for a tight looking fit.

$0 Price: $40.00

Buy Details

Availability: In-Stock Item
Item #: 11364 -

Concours correct white striped heater hose for 1967 and early (prior to 2/1/1968) 1968 Mercury Cougar and Ford Mustang. Durable white striping with no mention of "Autolite" - this particular hose did not come with that marking. Correct for all V-8 engines without air conditioning. The Cougars and Mustangs with air conditioning have a molded 90 degree elbow at one end. Some length trimming may be needed for a tight looking fit. Turn those hoses so that the white striping shows!

$0 Price: $33.17

Buy Details

Availability: In-Stock Item
Item #: 13765 -

For us with Cougars without factory AC. The originals were made of cardboard and are very prone to failure from moisture. These are made from virgin ABS black plastic and are excellent quality in every respect. Not often does a reproduction come along that blows away OEM, but this definitely is that part. Before you finish making your online order with us, go look at your plenum to see what condition your original is in. Replaces Ford part #: C5ZZ-18471-A

$0 Price: $1.25

Buy Details

Availability: In-Stock Item
Item #: 10735 -

Nut for attaching the power steering pump bracket onto the pivot stud coming out of the cylinder head. All 1967-69 Mercury Cougar and Ford Mustang engines additionally used on 1970 428CJ engines.

$0 Price: $19.98

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 16199 -

Used hinge for any 1967-68 Mercury Cougar or Ford Mustang. This hinge has two ribs formed for added strength. There was an early 1967 version of this hinge that did not have the ribbing. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint. Replaces Ford part number C7ZZ-6506050-B.

$0 Price: $19.98

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12962 -

Used hinge for any early 1967 Mercury Cougar or Ford Mustang. This early hinge is flat, the later 1967 and 1968 hinge had two ribs formed for added strength. Comes as shown, we select the best hinges to inventory, most will have the original dash color paint. Replaces Ford part number C7ZZ-6506050-A.

$0 Price: $60.05

Buy Details

Availability: In-Stock Item
Item #: 10514 -

Improved reproduction left hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit and adjust these hinges without the spring installed on them. We use an old section of seat belt for removing...

$0 Price: $89.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 14566 -

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

$0 Price: $60.05

Buy Details

Availability: In-Stock Item
Item #: 10513 -

Improved reproduction right hand hood hinge for the Mercury Cougar and Ford Mustang. Very heavy duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. It is easier to fit an adjust these hinges without the springs installed on them. We use an old section of seat belt for removing...

$0 Price: $89.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 14567 -

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

$0 Price: $101.55

Buy Details

Availability: In-Stock Item
Item #: 11092 -

Improved reproduction right and left hand hood hinges for the Mercury Cougar and Ford Mustang. Much heavier duty compared to the originals, thicker metal and slightly wider hinge bars. These hinges weigh 4.35 lbs, originals weigh 3.2 lbs. Hood hinge rivets have the 'plus' markings like seen on the 1969-70 hinges. Save your hinge springs, these do not come with the new springs. it will be easier to fit and adjust these hinges prior to installing the springs on them. We use an old section of...

$0 Price: $96.25

Buy Details

Availability: In-Stock Item
Item #: 14062 -

A modern touch to this classic muscle car look. This kit is the same Scott Drake "Shelby Style" Billet hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, machined billet aluminum top plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are Machined billet aluminum top plates and the deluxe is stainless steel. Common...

$0 Price: $63.35

Buy Details

Availability: In-Stock Item
Item #: 13779 -

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

$22.95 Price: $33.17

Buy Details

Availability: In-Stock Item
Item #: 42020 -

This kit is the same Scott Drake "Shelby Style" hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between this version and the deluxe version, is that these are chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the exact location varied from...

$0 Price: $25.97

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32039 -

Welded in hooked retainer for the rear seat back installation on any 1967-73 Mercury Cougar or Ford Mustang coupe or hard top body style. This bracket welds to the edge of the package tray. Two hooks per car, sold individually. We cut out a individual sections as shown. Make good measurements prior to removal of your old brackets. You will need to drill out the spot welds prior to installation. For sure that basic Ford part number is 62118.

$0 Price: $70.90

Buy Details

Availability: In-Stock Item
Item #: 23440 -

The High tone is indicated in raised letters located on the perimeter of the horn. The 1971-73 almost uses the same horn and bracket as the 1967-68, but was mounted at a different angle, so if you have a 1971-73 you will need to loosen the screw that holds the horn to the bracket and rotate the horn to the correct position.  These horns are close but not actually correct for a Cougar. 1967-68 Cougars used part number C7WF-13802-B Lo / C7WF-13801-B Hi and 1971-73 used D0DF-13802-A Lo /...

$0 Price: $81.85

Buy Details

Availability: Rare / NOS Part
Item #: 32844 -

New old stock, special molded California emissions rubber hose. Connects to the anti backfire valve, not sure where the other end attaches. About 12 inches long. Fits 1967 Mercury Cougar and Comet, and Ford Mustang and Fairlane, all with 390 thermactor smog.Ford part number C7OZ-9H534-B.

$0 Price: $25.15

Buy Details

Availability: Out of Stock
Item #: 13627 -

Reproduction Autolite gas tank to filler pipe hose fits the 67 to 70 Mercury Cougar, measures 4 1/2" long. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A. ...

$0 Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 26659 -

This Gas Tank To Filler Pipe Hose reproduction fits the 67, 68, 69, and 70 Mercury Cougar. Excludes 1970 with California emissions. Even if yours is not cracked it will be hard if it is over two decades old. We highly suggest you replace this part if yours is in fact hardened with age because a minor rear end collision could cause it to fail and send fuel spilling into your trunk area. Replaces Ford part #: C8ZA-9047-A.

$0 Price: $40.91

Buy Details

Availability: In-Stock Item
Item #: 41779 -

Both ends have 90 degree molded ends. Attaches heater core to water heater control valve.Replaces Ford Part #: C7ZZ-18472-CVAC.

$52.16 Price: $94.85

Buy Details

Availability: In-Stock Item
Item #: 13721 -

High pressure hose from the insulator to the control valve. All correct ribbing, striping, and crimping. Has correct colored protective sheathing.  This hose is factory correct for the 1967-68 390, 427 and 428 & 1969-70 302, 351, 390 and 428. This hose can also be used to reroute the 1967-68 289 and 302 to the big block routing when paired with the other 3 hoses needed (C9OZ-3A319-A, C8ZZ-3A713-A, C7AZ-3A005-A) and the 69-70 power steering hose bracket (C7ZZ-3C510-A and...

$0 Price: $45.80

Buy Details

Availability: In-Stock Item
Item #: 53273 -

NOTE: Some customers have mentioned this hose does not fit well, others have said it fits with no issues. It is not the same as OEM and fitment seems to depend on the vehicle and modifications that have been previously done. We recommend going with our premium version. Lower pressure hose for any 1967-70 Mercury Cougar and Ford Mustang, but with a V-8. The factory power steering pressure hose originally was a two piece hose. Valve end has the 5/16" flared male fitting, and a 3/8" female...

$50.00 Price: $57.47

Buy Details

Availability: In-Stock Item
Item #: 42029 -

This Pump to Value Outlet Pressure Hose is 100% correct for the 1967, 1968, 1969, 1970 big block. This hose has industrial high pressure fittings that are much higher quality than those available by most Mustang / Cougar Parts Dealers. Replaces Ford Part #: C9OZ-3A319-C. Click this link for more clarity on power steering hoses: https://secure.cougarpartscata... ...

$0 Price: $22.75

Buy Details

Availability: In-Stock Item
Item #: 31588 -

Reproduction hose that connects the oil cap to the air cleaner on cars equipped with the 289 engine. Replaces Ford Part number C6AZ-6A664-P

$0 Price: $275.00

Buy Details

Availability: Rare / NOS Part
Item #: 33589 -

NOS ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. Fits 1967-68 Mercury Cougar and 1966-69 Ford Mustang. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers,...

$0 Price: $47.88

Buy Details

Availability: Out of Stock
Item #: 18501 -

C6AZ-6A664-N Original used hose that connects the original PCV valve to the carburetor spacer plate. All 289-2V, 289-4V, 302-2V, and 302-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. Application for mid year 1966 through 1969 289/302 engines, including Cougar, Mustang, Falcon, Galaxie, Fairlane, Torino, Cyclone, Ranchero, and Comet. *Note - These molded and contoured hoses were...

$0 Price: $10.05

Buy Details

Availability: In-Stock Item
Item #: 41761 -

Concours correct with ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers, and carburetor spacer...

MSRP:$34.95
$34.95 Price: $29.05

Buy Details

Availability: In-Stock Item
Item #: 41893 -

Connects PCV valve to PCV transfer tube on the 390, 427-4V, and 428CJ. Inside diameter on one end is .45" the other end is .58". These should be tough to get on so that they will form a vacuum seal. Originally held on with wire clamps, we have those available here  Replaces Ford Part #: C8AZ-6A664-D. Fits Many 1966, 1967, 1968, 1969, and 1970 Mercury Monterey, Marquis, Ford Galaxie, with FE 390 Big Block Engines. We aren't sure why this hose was reproduced as shown. However it will...

MSRP:$29.99
$29.99 Price: $19.31

Buy Details

Availability: In-Stock Item
Item #: 41969 -

This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Two required per vehicle, sold individually. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper specs. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. Replaces Ford Part #: C6OZ-3A714-A or C6OZ-3A717-A. ...

$0 Price: $99.95

Buy Details

Availability: In-Stock Item
Item #: 14295 -

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. One piece design, meaning it differs from the original separate two piece pressure hose set. Upper and lower pressure hoses were what came on the cars originally. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you...