1967 Ford Mustang

This quality reproduction 1967 Mustang part can easily be made to fit your 1967 - 1968 XR7 or 1967 standard Cougar manual transmission console simply by drilling the two holes near the front for the spring clips that attach the pad to the console. See the diagram below for correct hole size and location. This plate was used on both three and four speed manual transmission Cougars equipped with the optional center console. Not for use on 1968 standard / decor consoles. Replaces Ford Part #:...

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

Automatic shifter arm pawl - early version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1967-70 Mercury Cougar, 1965-70 Ford Mustang, and 1965-66 Ford and Mercury full size cars with floor shift automatic transmissions. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need, this early pawl has a Ford part number...

Complete console shift assembly for the 67 - 68 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm. Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Excellent high quality reproduction of the automatic transmission shifter bezel / indicator assembly for the 1967 and 1968 Mustang without console and 1968 Mercury Cougar XR7-G with XR7-G console. While not technically correct, this bezel can also be used on non-console Cougars (1967-1968) without modification. Ford part # C7ZZ-7D443-C. Check out our video on rebuilding your shifter below: ...

Reproduction shifter boot for aftermarket shifters on 67 - 68 Cougars, or 64 - 68 Mustangs. Perfect fit for Hurst shifters and will accommodate other aftermarket shifters.   

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

This shifter bucket is used on all 1967 - 1968 Mercury Cougars and Ford Mustang with an automatic center console. Bare bucket with good shift detentes and bushing hole that isn't worn out. Ford part number C7ZZ-7A306-A Check out our video on rebuilding your shifter below: ...

This shifter bucket is used on all 1967 - 1968 Mercury Cougars and Ford Mustang without an automatic center console. Bare bucket with good shift detentes and bushing hole that isn't worn out. Ford part number C7ZZ-7A306-B. Check out our video on rebuilding your shifter This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to...

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

Fit and and function wise this is the same as the 1968 - 1973 XR7 button. However if you want 100% correctness then the 1967 button is different and there are no reproductions for this exact button. The 1967 button has a concave surface, while the 1968-73 button is convex. See the comparison photo below with the 67 deluxe button (Left) next to the 68-73 button (Right). This is a replated part with no pits or cracks. Ford part number C7ZZ-7C488-B. $20 refundable core charge will be added. Click...

Fit and and function wise this is the same as the 1968 - 1973 XR7 button and we suggest the quality reproduction we offer as a good replacement. However if you want 100% correctness then the 1967 button is different and there are no reproductions for this exact button. The 1967 button has a concave surface, while the 1968-73 button is convex. See the comparison photo below with the 67 deluxe button (Left) next to the 68-73 button (Right). This is a good used part with no pits or cracks. Ford...

Steel retaining plate. Ford part number C5ZZ-7B233-A. This plate is needed to fasten the shift indicator bezel on non-console cars. Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang, without console. Nice reproduction part, better value than used. You may also need a set of 4 attaching screws. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1967 - 1968. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one.Replaces Ford Part #: C5ZZ-7213-F.

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

C5ZZ-7210-C Shift lever for all 1967 Mercury Cougar and Ford Mustang and 1968 until 1-2-1968. The early lever can be identified by measuring the distance between bolt holes. 1-13/16" spacing between the holes is the C5ZZ-7210-C lever. *Note - Must be used with Trunion C5ZZ-7210-D, sold separately.

C5ZZ-7210-M 4 Speed shifter lever with reverse lockout provision. For any 1967 Mercury Cougar and Ford Mustang with V-8 engines. *Note - Must be used with Trunion C5ZZ-7210-D, sold separately.

C5ZZ-7400-D 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968.

Adjustable rod that connects the floor shifter to the "Select-Shift-Merc-O-Matic" automatic transmission. C4 transmissions only, code "W" on your door data plate tag. Small block 289/302 engines received the C-4 automatic transmissions. Rod marked C7ZA-7326-B. Shift rod approximately 17-1/4 inches long. Check out our video on rebuilding your shifter below: ...

Reproduction adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions.Includes pin and nut. Shift rod approximately 18 inches long. Replaces Ford part number marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the big block C-6 automatic transmissions. C6 transmissions only, code "U" on your door data plate tag. FE big block 390/427/428CJ engines received the C-6 automatic transmissions. Shift rod approximately 17 inches long. Rod marked C7ZA-7326-A. Check out our video on rebuilding your shifter below: ...

4-Speed shifter rod hardware kit for 67 - 68 Cougars and Mustangs with a 4-speed transmission. Check out our video on rebuilding your shifter below: ...

This hard plastic part slips over your floor shifter stem and keeps coins and such from falling inside your center console. Replaces Ford part number C7ZZ-7C445-A. Check out our video on rebuilding your shifter below: ...

Reproduction "U" shaped bracket that attaches the 3 /4 speed shift lever to the shifter control assembly. For use on all 67 - 68 Mercury Cougar and Ford Mustangs with the 3 or 4 speed shift lever, and 1968 shift levers through 1-2-1968. Measurement of hole spacing is 1-13/16 inches on center. *NOTE - Must be used with 3 speed shift lever C5ZZ-7210-C, or 4 speed shift lever C5ZZ-7210-M. Replaces Ford part number C5ZZ-7210-D Check out our video on rebuilding your shifter below: ...

KYB Gas-a-just shocks are America's best selling performance gas shock. It's monotube design features a higher gas pressure which helps to hold the tire to road surface during severe driving conditions. N2 gas helps eliminate shock fading due to aeration and foaming. This shock is the perfect choice for the performance oriented. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.029.614.41-X- ...

These are equal in performance to other name brand high pressure gas shocks at a significant lower price. These shocks are best suited for drivers looking for firm ride with a solid controlled “feel of the road”. These units are sold individually.

This gas shock improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock. Also, this is the most stock-looking shock since it's black and has a flat upper collar. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.259.334.92-X- ...

Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually

If you buy this reproduction tower, you will no doubt save you time in clean up. But nothing will ever fit and look like original FoMoCo towers!Here's a little film to help you fortify your flexxy feline!

Excellent condition tower as cut from a Western parts car. No specific part number for this structural front suspension section.Generic Ford part # C7ZZ-16055-D or E, includes apron and side member.Here's a little film to help you fortify your flexxy feline! ...

We highly suggest you look at our mint condition used towers for about the same price. Why mess around with repo when you can get FoMoCo?!Here's a little film to help you fortify your flexxy feline!

Excellent condition tower as cut from a Western parts car. If you are replacing two towers because of cracks, we strongly suggest upgrading to a 1969-70 pair of reinforced towers. The 69 and 70 towers are an exact fit into your 1967-68 Ford Mustang or Mercury Cougar. There are no specific part numbers for this structural front suspension section.Generic Ford part #s C7ZZ-16054-C or C7ZZ-16054-E, includes apron and side member. Here's a little film to help you fortify your flexxy feline! ...

Used driver side shock tower and apron assembly for the Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Used passenger side shock tower and apron assembly for the Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Solid, undamaged driver and passenger side shock tower braces. Fits all 1967-68 Mercury Cougar and Ford Mustang. Ford part #s C5ZZ-16A053-B driver side (left hand) and C5ZZ-16A052-C passenger side (right hand). *NOTE* Excludes 1967-68 Mustang Convertible. **Installation Tip** These brackets attach under the cowl lip. ...

Individual reproduction shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.

Individual reproduction shock tower cap or coil spring cover in black for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.

Individual used shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. While not technically restored original, we offer these to complement our chrome export braces and Monte Carlo bars.  Ford part # C7ZZ-18A017-A.

Used shock tower cap for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. These used pieces are superior to the reproductions because they are constructed from thicker metal. Plus, you just can't beat original FoMoCo!Ford part # C7ZZ-18A017-A.

Shock tower coil spring cover installation hardware that fits Cougar and Mustang coupe, fastback and convertible.

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 1-1/4 from wheel surface. These will work with our aftermarket Ford wheels without trim rings. These have the Dill 627 caps. Same as the 1960's cars.