1967 Ford Mustang

Grade A lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561705-F.

This adjustable linkage kit connects the left track to the right track on a bench seat. Original Ford part number C5ZZ-6561726-B. Ford description: Rod - Front Seat Track Tie. Listed for Mercury Cougar and Ford Mustang bench seats 1967-1969.

Grade A non lever side of the seat track assembly for the 67 - 70 Mercury Cougar or Ford Mustang. Ford master part number C5ZZ-6561704-F.

Easy to install, correct tension and length. Includes All the Springs Necessary to Rebuild One Seat. Black Phosphorous Plated. Bucket or Bench seats - 2 kits required for bucket seats. Replaces Ford Parts: (2 - Track assist springs) C5ZZ-6561828-A and (1 - Track latch spring) C0DZ-6461883-A.

Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Sold individually.Replaces Ford Part # C5ZZ-13190-K

Sold in a set of eight, these are the same gauge steel as originals. Installs between seat track and carpet. Four per bucket seat, normally only seen on the 1967 model year. These reproductions work fine but look a little different than the originals.Replaces Ford Part # C5ZZ-13190-K

This plastic linkage rod / arm connects the floor shifter to the indicator light inside your console that illuminates the PRND21 on your illuminated console panel. Used on all automatic consoles 1967 -1968 XR7 and standard. Ford part number C7ZZ-7E148-A. Check out our video on rebuilding your shifter below: ...

This plastic linkage rod / arm connects the floor shifter to the indicator light inside your console that illuminates the PRND21 on your illuminated console panel. Used on all automatic consoles 1967 -1968 XR7 and standard. Ford part number C7ZZ-7E148-A. Check out our video on rebuilding your shifter below: ...

1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. These are used, and because of the low grade of chrome plating, these will show some form of light pitting.  handle, which is larger and has a faux leather covered handle in a variety of colors. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Tired of picking your broken button off the floor? This inserts in the left hand side of your deluxe (colored keyed) shift handle. Quality part made in China, please consider our good used units at half the price! 67 is actually a little different in contour but this will fit fine. Replaces Ford #: C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Black plastic selector button for all 1968-72 Mercury Cougar and Ford Mustang with automatic transmission. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M and C5ZZ-7C488-D. Your buttons may have faded to gray after many years. These black buttons are injection molded plastic and have steel wear plates just like the originals. Technically this is a copy of the...

Black plastic selector button for all 1967 Mercury Cougar and 1965-67 Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-M. Check out our video on rebuilding your shifter below: ...

Black plastic dummy button for all 1967 Mercury Cougar and 1965-67 Ford Mustang with automatic transmission. This is for all cars with body type 65A, 65C, 63A, or 76A. This is the non-moving button on the right side of your shifter handle. This is for all cars with body type 65A, 63A, or 76A. This is for the base model shifter handle. Deluxe shifters were larger and had simulated leather wrapping. Ford part C5ZZ-7C488-D.

Early (before 4/10/1967) 390 oil pressure sending unit. Non-XR7 style, Mercury Cougar body codes 65A & 65C. Ford Mustang with oil light. *Note - this sending unit uses the push on wiring connector instead of the clip on connector. Please check your wiring harness for compatibility.Check out the video below on our new gauge tester: ...

Big bell shaped oil pressure sending unit for 1967 Mercury XR7 and 1967 Ford Mustang with actual oil pressure gauges instead of idiot light for the oil pressure. *Note - this pressure switch does use the 'nail head' connector. Please check your wiring harness for the proper connector.Replaced Ford part # C7ZA-9275-B Check out the video below on our new gauge tester: ...

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

These are correct reproductions of the A/C discharge service valve that comes with plastic caps. if you would like the correct aluminum valves, we sell those separately.

Used A/C discharge service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used high pressure or discharge valve for installation on either York or Tecumseh air compressors. Has the 3/4" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and...

Reproduction A/C suction service valves for Mercury Cougars and Ford Mustangs equipped with factory A/C.

Used A/C suction service valves for 1967-68 Mercury Cougars and Ford Mustangs equipped with factory or integral A/C. Original assembly line used low pressure or suction valve for installation on either York or Tecumseh air compressors. Has the 7/8" inch flare fitting for suction hose. Note that this has the 'Flare' style of hose connection, also 'Rotolock' is used to describe this style of valve. We consider these core grade valves. They should be professionally inspected and have...

Exact reproduction pair of originals and a must for that detailed engine compartment, but in stainless steel. It is little details like these that will often separate 1st from 2nd place at a show.Replaces Ford part # C5ZZ-19752-C.

Used servo cover from a 1967-68 Ford C-4 transmission. This cover has the big A cast into it, which designates it as an "A" servo. Cover only, marked C6AP-7D027-C.

378696-S Special set screw for the front door channel and vent window frame. This one is longer than the one that installs in the rear door window guide. This set screw has a 5/32" hex head with 5/16" NC threads and is 1-7/8 inches in overall length. This set screw also has a 1-1/8 inch diameter shoulder. Sets and holds your front door glass and vent window angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual...

Shaft or rod for the A/C damper blower door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft is clocked differently than the 1969-73 version. This air conditioning damper door is in front of the blower or fan in the center of the car. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number...

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1968-70 shaft which had a Ford part number of C8AZ-2478-A. This version uses a special spring clip. We also sell the 1967 shaft, which uses a hairpin clip and washer.

Shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. This is a reproduction of the 1967 shaft uses a hairpin clip and washer on the end. We also sell the 1968-73 shaft, which uses a spring clip.Ford part number of C6AZ-2478-A.

Used shaft or pivot pin for installing the drum brake pedal on any 1967 Mercury Cougar or Ford Mustang with automatic transmission. We do not have the spring clip available. Ford part number of C8AZ-2478-A. 

Shaft or rod for air inlet damper door for any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-A.

Shaft or rod for the evaporator damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. 1967-68 shaft has a tab mounted on the lever, and is clocked differently than the 1969-73 version. The evaporator damper door allows air to pass over the evaporator in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related...

Shaft or rod for the heater damper door on any 1967-68 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater damper door allows air to pass over the heater core in the fiber glass A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for damage or weakness of the metal. Shaft only, door not included, but available. See related parts.Replaces Ford part number C7ZZ-19C774-B.*Note will not work in 1969-73 A/C boxes.

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with C-4, automatic transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always...

Accelerator pedal shaft assembly that mounts to the engine firewall. For use with small block 1967-68 Cougars with manual transmissions. This same assembly is used on small block Ford Mustangs 1966 - 1968. These assemblies are just the main shaft only, and do not come with the accelerator pedal or the throttle linkage. These made in Taiwan assemblies are pretty decent looking but for less money we have original FoMoCo which with a little TLC will look better and the fit is always superior.Ford...

This 1967-68 Mercury Cougar and Ford Mustang shield, was installed at the factory to protect the heater motor from being damaged when the Big Block 390-427-428's were being dropped in. As noted in the factory assembly manuals we sell, they were supposed to be removed once the motor was in place. We have found that more often than not they were left in place as it was probably too time consuming to remove them. Technically they should not be in place on a concours car but practically...

This arm is attached to your automatic transmission floor shifter (see picture at left). Ford calls technical name for this part is 'Arm, Support'. These used parts will come with an intact bushing and nut. Correct for C-4 and C-6 transmissions. Ford part number C7ZZ-7302-A. ...

C5ZZ-7400-D4Assembly 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang. Small block 289 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition.  Check out our video on rebuilding your shifter below: ...

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

This 4 Speed Lower Shift Boot attaches to the bottom side of your shifter to protect it from water and dirt. Fits the 67 and the 68 with 289 or 302 engines only Replaces Ford part #: C6ZZ-7138-C.

This reproduction of the 3 and 4 Speed Shift Boot has a metal core base just like original as is the texture. Fits the 67 and the 68. Replaces Ford number C5ZZ-7277-B. Customer feedback found at mercurycougar.net : When I bought my 68xr7 from Don two years ago, our deal was that he would keep the new Magnum 500's and BFG tires that were on the car. I asked him if he would just put some "rollers" on to get the car on and off my dad's trailer. When I got the car, he had put on a...

This bezel was never offered from the factory on a Cougar, but is a very attractive part for those with a manual transmission and no console. This unit works with three or four speed manual transmission and with a rubber or leather shift boot.

Original style, factory 3 speed lower shift boot.Replaces Ford part #: C6ZZ-7138-B

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This shifter dial was originally attached with heat to a pin connector. To reattach we suggest using glue. These look like it would be easy to detail the white letters for P R N D 2 1 with a careful hand. May have a chipped corner that is not seen when installed. Ford part # C7ZA-7A213A Check out our video on rebuilding your shifter below: ...

Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.

Shift kit for the C6 transmission valve body for all 1967-73 and 1967-73 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.

Nice reproduction 3 speed black shift knob for the 1967 Mercury Cougar and Ford Mustang and other floor shift Ford products from 1967. Thread size is 1/2-20, will not fit on 1968. Ford part number C5ZZ-7213-H. Check out our video on rebuilding your shifter below: ...

This one might cost a couple dollars more than others you may have seen but it is the best in my opinion. This is correct for a standard Cougar, XR7 had a woodgrained finish. Check out our video on rebuilding your shifter below: ...

For those who want to want a correct looking interior in conjunction with their modern transmission. Check out our video on rebuilding your shifter below: ...

Used on both XR7 and standard Cougar consoles. Differs from shifters made for non console use in that is has a small loop to connect the white plastic arm to the shift indicator light. Fits 1967-68 Mercury Cougar and Ford Mustang with factory consoles. Good used part no heavy pitting on the chrome, comes with complete with cable assembly inside. Ford part number C7ZZ-7210-C. Check out our video on rebuilding your shifter below: ...

Restored chrome automatic shifter lever for any 1967-68 Mercury Cougar or Ford Mustang with consoles. This console lever is unique to console equipped cars, it has a tab with a hole in it for accepting the shift indicator indicator rod. We sell these bare for those car owners that have pitted shifter levers. Ford part number C7ZZ-7210-C. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...