Contact Us / Visit Us (click here)
If the Shopping Cart takes too long to respond, you can bypass the shopping cart and go straight to the checkout page by clicking the following link: Checkout.
International Customers Click Here [Updated 1/2024]
Loading Trivia . . .

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 2641-2688 of 3199
Price: $1,200.02

Buy Details

Availability: Out of Stock
Item #: 27513 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1967 late 9 inch rear end housings without fill plug in the steel...

Price: $132.89

Buy Details

Availability: Out of Stock
Item #: 20256 -

Correct for closed emission system Cougars sold only in California. Air cleaner base for both the 289-2V and 289-4V engines. About 17.25" inches in diameter. California emissions with the metal elbow for hose connection to the oil filler cap.

Price: $74.88

Buy Details

Availability: Out of Stock
Item #: 16002 -

Good used tray that is not currently reproduced. Most people prefer the group 24 battery but for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting). Many that are not rotted have been cut to accept a group 24.

Price: $174.87

Buy Details

Availability: Out of Stock
Item #: 30632 -

Good used group 24 tray for 1967 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray with holes for tilt vacuum canister. For those that want to keep it very original, this version is not reproduced. This is getting to be a hard to find part with no rot (will show pitting).

Price: $14.75

Buy Details

Availability: Out of Stock, On Order
Item #: 12337 -

New front inner wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.25 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

Price: $13.85

Buy Details

Availability: Out of Stock, On Order
Item #: 13691 -

New front outer wheel bearing for original drum and disc brakes for all 1967-69 Mercury Cougar and 1967-69 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.75 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the 1967-69 spindles,...

Price: $25.88

Buy Details

Availability: Out of Stock
Item #: 15-0057 -

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Price: $38.88

Buy Details

Availability: Out of Stock
Item #: 31478 -

Used Bell Crank from the Servo Assembly on any 1967-68 Mercury Cougar or Ford Mustang with speed control. Attaches to the Connector, via a Shaft, and Trunnion is attached. Ford part number C7ZZ-9B713-A.

Price: $224.87

Buy Details

Availability: Out of Stock
Item #: 16-0080 -

C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate.  Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. Ford master part number C5OZ-7976-A. . ...

Price: $80.87

Buy Details

Availability: Out of Stock
Item #: 31333 -

C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate. Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. NOTE * Grade B bell housing will have a chip or heavy scarring on the bottom, see photo...

Price: $225.86

Buy Details

Availability: Out of Stock
Item #: 23857 -

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Price: $435.87

Buy Details

Availability: Out of Stock
Item #: 16-0068 -

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C6OZ-6392-B. The latest research shows that the casting number C60A-6394-B bellhousing may have been for 1966-68 Cougar, Mustang, Fairlanes and Comets with an 11 inch clutch disc.  Shipped bare, no hardware or clutch fork.

Price: $21.87

Buy Details

Availability: Out of Stock
Item #: 15-0065 -

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

Price: $74.85

Buy Details

Availability: Out of Stock
Item #: 32848 -

Used radio bezel Grade A used. For use on 1967-68 Mercury Cougar or Ford Mustang cars without console. 2-3 different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

Price: $259.88

Buy Details

Availability: Out of Stock
Item #: 24309 -

Very rare find... A restored bezel will look fine but will never retain the sharp edges and matte black finish like this new in the box original Ford part.

Price: $260.87

Buy Details

Availability: Out of Stock
Item #: 32633 -

This shift indicator will work on a 1967 or 1968 Cougar or Mustang equipped with automatic transmission. It comes with all items shown here.

Price: $427.50

Buy Details

Availability: Out of Stock, Discontinued
Item #: 30175 -

Polished billet aluminum hood hinges that replace the factory hood hinges and springs with a hydraulic strut hinge.  Comes with medium duty struts for fiberglass hoods or heavy duty struts for factory / repro steel hoods.  Mounts using the same holes as the factory hood hinges with the included mounting hardware.

Price: $90.62

Buy Details

Availability: Out of Stock
Item #: 20556 -

Reproduction heater blower motor for Mercury Cougar and Ford Mustang that is a high quality replacement part at a reasonable price. However, these off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the...

Price: $1.05

Buy Details

Availability: Out of Stock, On Order
Item #: 27549 -

New rubber body plug, fits oval rear shock access hole. 1-3/4" x 3-5/16" oval holes. Sold individually, Usually 2 per car. Fits 1967-70 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378923-S.

Price: $169.88

Buy Details

Availability: In-Stock Item
Item #: 23892 -

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

Price: $5.85

Buy Details

Availability: Out of Stock
Item #: 23776 -

Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.

Price: $3.15

Buy Details

Availability: Out of Stock, On Order
Item #: 41026 -

Four required per seat, eight per car equipped with bucket seats. Actual bolt length is 1-1/2 inches.Sold individually. 

Price: $25.88

Buy Details

Availability: Out of Stock
Item #: 11-0428 -

Used Vent Frame Bolt Kit 1967 and 1968 Mercury Cougar and Ford Mustang. Consists of: 1 bolt - 379384-S2 1 bolt - 378694-S 2 lock nuts - 33797-S2 set screws -  375694-S2

Price: $0.85

Buy Details

Availability: Out of Stock
Item #: 30964 -

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...

Price: $61.88

Buy Details

Availability: Out of Stock
Item #: 23929 -

Application - 289 with air conditioning and 390 with or without A/C.

Price: $52.85

Buy Details

Availability: Out of Stock
Item #: 31304 -

Detachable mounting plate for installing the passenger side convertible ram cylinder, to the convertible top frame assembly behind the quarter interior panel. Right and left are the different, fits all 1969-70 Mercury Cougar and 1965-70 Ford Mustang convertibles. Ford part number C5ZZ-76531A18-A.

Price: $139.85

Buy Details

Availability: Out of Stock
Item #: 24080 -

For any year 1967 1968 1969 1970 Mercury Cougar with an FE 390, 427, or 428CJ engine. Identified by the round dimple stamped into it. Compare the OEM used part price to the reproduction part. For restoration purposes, this bracket was factory painted satin black.

Price: $21.82

Buy Details

Availability: Out of Stock
Item #: 32040 -

Reproduction bracket for mounting the rear axle flexible brake hose. From the factory, these brackets were welded in. Double check your placement for your particular year, when welding the bracket to your car. Has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Replaces Ford part number C7ZZ-2A051-A.

Price: $75.87

Buy Details

Availability: Out of Stock
Item #: 31449 -

Used Bracket for mounting the Servo on any 1967-68 Mercury Cougar or Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C736-A.

Price: $95.85

Buy Details

Availability: Out of Stock
Item #: 24267 -

The originals hang at a slightly different angle than the reproductions. Comes as shown with original rubber insulator. New rubber available upon request. Seldom in stock, we suggest the 1969 small block version. It is very close to this one. Please see related item. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Replaces Ford part # C7ZZ-3C510-A, and C7ZZ-3C510-C.

Price: $69.15

Buy Details

Availability: Out of Stock
Item #: 25930 -

Reproduction power steering hose retaining bracket and retainer. This is the bracket needed if you are routing the PS lines under the lower control arm instead of over as found on the 67 - 68 small block. Bracket and retainer will work on 1967-70 Mercury Cougar and Ford Mustang with small block V8 cars with the correct length of power steering hoses.

Price: $53.87

Buy Details

Availability: Out of Stock, Discontinued
Item #: 25931 -

Fits 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.

Price: $34.88

Buy Details

Availability: Out of Stock
Item #: 19866 -

Two of these little plastic protectors came on Mercury Cougars and Ford Mustangs equipped with Air Conditioning. They are affixed to the front cross member using the same bolts that holds your condenser in place. Their purpose was to protect the wiring harness from potential damage if the car were to get into a collision. These are very hard to find today as most were discarded the first time the condenser was replaced. Even your most experienced judges usually have never seen or heard of this...

Price: $69.89

Buy Details

Availability: Out of Stock
Item #: 31941 -

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561693-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

Price: $69.89

Buy Details

Availability: Out of Stock
Item #: 31942 -

This flexible vinyl cover attaches to the upright brackets that mount your center fold down arm rest. The number stamped on the back for the cover closest to the driver is C5ZB-6561692-BW. If yours is other than black in color the BW will be something else. Very rare part that is difficult to obtain.

Price: $31.95

Buy Details

Availability: Out of Stock, On Order
Item #: 11805 -

Reproduction passenger side (right hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits in a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2061-B or C9TZ-2061-B.

Price: $98.87

Buy Details

Availability: Out of Stock
Item #: 24619 -

C9OZ-2212-C Left hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70867. Originally manufactured by Bendix part number 319480.

Price: $98.87

Buy Details

Availability: Out of Stock
Item #: 24617 -

C9OZ-2211-C Right hand rear brake backing plate for use with 1-3/4 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Also used on 6 cyl and 302 Mustangs in 69-71. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 70866. Originally manufactured by Bendix part number 319481.

Price: $179.87

Buy Details

Availability: Out of Stock
Item #: 24618 -

C9OZ-2212-B Left hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71086. Originally manufactured by Bendix, part number 317558..

Price: $179.87

Buy Details

Availability: Out of Stock
Item #: 24616 -

C9OZ-2211-B Right hand rear brake backing plate for use with 2 inch wide brake shoes. Clean Western part with no heavy corrosion like you see on Eastern cars. Inspected for excessive wear. Used on cars with 10" drums.Originally manufactured by Kelsey-Hayes, KH part number 71085. Originally manufactured by Bendix, part number 317559.

Price: $247.37

Buy Details

Availability: Out of Stock
Item #: 13615 -

Complete Midland core booster with both input and output rods in place. No visible cracks in bake-a-light plunger. Will show some rust pitting, most notable on the bottom side where previous leaking master failed, but not excessive. Check out our videos below, one on how to convert a manual drum brake car to factory disc brakes, and the other on boosters, differences, do's / don'ts: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury...

Price: $307.69

Buy Details

Availability: Out of Stock
Item #: 30967 -

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Price: $400.01

Buy Details

Availability: Out of Stock, Discontinued
Item #: 11489 -

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

Price: $400.37

Buy Details

Availability: Out of Stock, Discontinued
Item #: 30968 -

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Price: $189.85

Buy Details

Availability: Out of Stock, Discontinued
Item #: 31799 -

We have discontinued this booster because of changes that made it no longer fit correctly. This reproduction brake booster looks and fits more like the originals than any other on the market. This is an off-shore unit, but of the many out there, it is the only one we feel you can consistently get 10 or more years out of. It comes with a 3 year warranty and no core exchange is required. If you do have a decent original core (any version 1967 - 1970 Midland or Bendix brand), we can credit...

Price: $400.01

Buy Details

Availability: Out of Stock, Discontinued
Item #: 25921 -

This option includes paying a core charge. By choosing this option, the rebuilt booster you receive will have started the rebuild process as an average quality core.We highly recommend that you send us your core first. Here's why:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a...

Price: $400.01

Buy Details

Availability: Out of Stock, Discontinued
Item #: 30965 -

This option REQUIRES sending your core in advance. Here are the advantages of pre-sending your core:We can core match your booster. Boosters that are rebuilt using a superior quality core are always reserved for core matching. If your core is average or below average, you may be able to pay to upgrade to a rebuilt booster that started the rebuild process as a superior quality core.You can find out the quality of your core before paying a core charge and avoid unnecessary core charges....

Price: $93.47

Buy Details

Availability: Out of Stock
Item #: 25915 -

These new brake drums are perfect replacements for tired and thin originals on you Cat or Pony. Fits cars with either the 2 1/4 inch or 2 1/2 Inch shoes. Front drums do not include studs or a hub. Drums Provide Consistent Quality & Reduced Noise.; Drums Are Vehicle Specific & Meet Federal Safety Standards.; Castings Meet Sae J431/g3000 Specifications For Proper Tensile Strength.; Machined To Control Perpendicularity & Run-Out For Optimal Performance & Brake Life.Also fits V8...