1967 Ford Mustang

Used vacuum tank or canister for the early built 1967 Mercury Cougar and Ford Mustang with factory or integral air conditioning. According to the Ford Master Parts Catalog, the cutoff date for this A/C canister was December 1967. Later cars used the common two nipple vacuum cans that mount inside the passenger side fender below the hood hinge on the passenger side.Replaces Ford part number C7ZZ-19A566-A.

Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...

This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength.  Replaces Ford part # C8ZZ-19A566.

Reproduction Air Conditioning Vent Air Door Axle for the 1967 and 1968 Mercury Cougar or Ford Mustang.

Round air conditioning vent registers for all 1967-68 Mercury Cougar and Ford Mustang with factory A/C.

Reproduction factory air conditioning vent register knob. This knob controls the black vent door or valve inside the round registers. These will fit the original axle shafts, but will need to be attached with some super glue or other adhesive. These new knobs fit our reproduction axle shafts that have new splines on them perfectly. Please note the position or orientation of the knob in relation to the position of the internal black plastic butterfly.

Black plastic retainer for attaching the direction air conditioning vent registers.

This reproduction A/C vent register with knobs is show quality and a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs and dealer pricing available.

Reproduction passenger side A/C vent with black camera case finish for the 67 - 68 Mustang. 

Reproduction driver side A/C vent with black camera case finish for the 67 Mustang.

part # 370608-S. Used in multiple places on mounting brackets.

This Accelerator Pedal Rod To Firewall Grommet reproduction fits both the 67 and the 68. Replaces Ford part # C6OZ-9793-A.

Reproduction diaphragm pump that mounts on the front all 67 - 73 Cougar or Mustang Autolite 2V carbs as well as 1967 Autolite 4V Carbs. With today's gas, these commonly fail, especially when sitting for extended periods of time. Complete failure will cause fuel leaks, but many times these will affect performance well before a leak actually starts. Good idea to replace every few years or if sitting for 6 months or more. Replaces Ford Part #: C4AZ-9B559-A.

Molded rubber plug, seals access hole in the side of shift housing. Replaces Ford Part # : C5ZZ-7C147-B Check out our video on rebuilding your shifter below: ...

Floor shifter access plug. 1967-73 Mercury Cougar and Ford Mustang, also fits floor shift 1971+ Mercury Comet and Ford Maverick. Ford Part number C7ZZ-7C147-A. Check out our video on rebuilding your shifter below: ...

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

Reproduction center cap adapter kit for installing Legendary center caps on the Legendary Series GT9 wheels. The spacing is a bit deeper on these specific wheels, so this adapter kit comes with special adapters and longer screws.  This kit is intended to make original and after market Mag 500 and Style Steel wheels center caps work on the Legendary Series GT9 wheels.  Please note that the included screws may not fit the thread pattern of some center caps.  The plates will...

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the black colored adhesive and is the 5 ounce size.

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the yellow colored adhesive, the factory used yellow adhesive on the weather stripping and is the 2 ounce size.

New 5oz tube of yellow weatherstrip adhesive for installing the rubber weatherstripping found on the Mercury or Ford. This 3M brand adhesive is a great match to the yellow colored adhesive that Ford used to attach the weatherstripping on many of it's vehicles back in the day.

The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...

Economy Small Block Powering Steering Adjustment Bracket. Lighter weight material than OEM. Replaces Ford Part #: C7SZ-3A732-A.

Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .

Used alternator adjusting bracket for early 1967 Mercury Cougar or 1965-67 Ford Mustang with 289 V-8 engines. Very early style which is a carryover from the 1965-66 289 alternator bracket. The difference of this C5AE-10145-A alternator bracket and the C7OE-10145-A bracket is the C7OE bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys. To be safe, we recommend the C7OE-10145-A bracket for clearance purposes. Ford part number...

Used alternator adjusting bracket for any 1967-68 Mercury Cougar or 1967-68 Ford Mustang with 289 or 302 V-8 engines. C7OE-10145-A stamped bracket has a slightly rounded off end to prevent contact with some of the larger diameter water pump pulleys from previous years. Ford part number C7OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...

Used alternator adjusting bracket for any 1967 Mercury Cougar or Ford Mustang with 390 engine and without smog. Also fits Shelby GT-500.Replaces Ford part number C6AE-10145-B, or it is stamped C6AE-B

Application is 1967 - 1968 289/302 and 1969 Boss 302 Eliminator alternator adjusting with factory air injection emissions. Casting number C6OE-10145-A, Ford part number C6OZ-10145-A.

Application is 1967 390 with California emissions. Casting number C6AE-10145-A. Ford part number C6AZ-10145-A.

This high performance alignment kit replaces the factory eccentric bolt and cam that holds the lower control arm to the frame. The eccentric cam is used for setting wheel camber. When the eccentric is turned, the lower arm moves in or out changing camber. Stock eccentric cams can slip or rotate going over bumps, allowing the alignment to change. Which is the cause of many worn tires. The lower control arm adjusting cam eliminator kit replaces the eccentric bolt and cam with non slipping...

Sleeve and hardware for joining the inner and outer tie rods together. This also is a 'toe in' adjustment part. Sold individually, two needed per car. Replaces Ford Part #: C2AA-3310-A

Ford Part # 379390-s Sold individually

Includes a pair of chrome screw adjusters, nuts and washers, heavy duty plastic rest plates and attaching screws to repair or replace that missing seat back adjustment.Replaces Ford Part #: C1DZ-6461643

Fits 1967 Standard or XR7

Reproduction 1967 GT concours correct air cleaner assembly with the chrome lid for the Mercury Cougar and Ford Mustang equipped with the 390 engine. Notice that this version does not have the metal elbow on the side for the hose going to the oil fill cap? This is an extremely hard piece to find used and even rarer in NOS form. Now we can offer you this new unit that is made from the original tooling! This reproduction includes a blue base, a chrome lid, and a lid to base rubber gasket. Some...

Reproduction GT style concours correct air cleaner assembly with a chrome lid and California emissions tube for all Mercury Cougars and Ford Mustangs equipped with the 390GT engine. This is an extremely hard piece to find used and even rarer in NOS form. Now we can offer you this new unit that is made from the original tooling! This reproduction includes a blue base, a chrome lid, and a lid to base rubber gasket. This is also an excellent stock appearing performance upgrade for the very...

This air cleaner assembly never came from the factory on any Cougar, but was an over the counter option available from your Ford dealer. If you have a very nice hood blanket I would think twice before using it in conjunction with this air cleaner assembly as it will leave an imprint. To avoid this problem with small block cars you can use a lower profile carburetor spacer, but on big block cars this is not an option due to the already thin design of the factory carburetor spacer. This will...

Sold individually. Used on factory 2V Ford carburetors. Zinc (dark gray)

Reproduction carburetor stud for all Ford numbered Holley carburetors 1967-71. 1/4-20 double ended stud from AMK. Stud only, no wingnut. 

This is a reproduction of the original orange engine displacement decal with a black and white checkerboard background on each end. Located on the top of the air cleaner.Fits the following models with a 289 4 barrel engine:1967 Mercury Cougar 1967 Ford Mustang Replaces Ford Part #: C5ZF-9638-D ...

This is a reproduction of the original orange engine displacement decal with a black and orange checkerboard background that was located on the top of the air cleaner.Fits the following models with a 289 4 barrel engine:1967 Mercury Cougar1967 Ford Mustang

This is a reproduction of the original orange engine displacement decal with black lettering and black and white checkerboard on each end that was located on the top of the air cleaner. This decal is for models without the GT package.Fits the following models with 390 4 BBL engines:67 Mercury Cougar1967 Ford Mustang Replaces Part #: C5AF-9638-D ...

This is a reproduction of the original orange engine displacement decal with black lettering and orange checkerboard on each end that was located on the top of the air cleaner. This decal is for models without the GT package.Fits the following models with the 390 4 barrel engine:1967 Mercury Cougar1967 Ford Mustang

This is a reproduction of the original Autolite spark plug decal that was located on the air cleaner.Fits the following models:1967 Mercury Cougar1967 Ford Mustang ...

Nice used air cleaner assembly, includes base, snorkel, heat riser and air cleaner lid. Application is any 1967 Mercury Cougar or Ford Mustang with C code 289-2V or A code 289-4V engines without emissions. All good parts as shown, thermal switch in air cleaner snorkel may not work, and no we cannot test them.Even if you are not currently running all original parts under the hood this is a great set to stow away as these items are going up in price and add value to your car when the time comes...

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

We offer this "Core Grade" assembly for those that purchase the various 1967 reproduction air conditioning bezels. This assembly will provide the needed 'guts' for behind the various 1967 Mercury Cougar or Ford Mustang A/C and heater control bezel. A Complete A/C heater control assembly includes bezel or face plate(bezel will be pitted and possibly broken), bracket control mounting plate, electrical and vacuum switches, and hardware. *NOTE* - Does not include knobs or cable.Ford part #...

This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. * This filter fits primarily Big Block cars, but a couple of other combinations, so grab a tape measure and double check the height of the one you need to replace, as that will tell you which one you need. Air Filter Height (Inches) : 2.193" Air Filter Height (mm) : 55.7 mm  Air Filter Bottom I.D. (Inches) : 11.32" Air Filter Bottom I.D. (mm) : 287.53 mm Air Filter...