1967 Ford Mustang

Partially dipped clip for attaching the fuel line harness or trunk wiring harness, or fuel line at fuel tank. Found in various places on 1967-70 Mercury Cougar and Ford Mustang.

Reproduction Lower Radiator Core Support Loom Clip for the 1967 - 1968 Mercury Cougar / 1967 - 1968 Ford Mustang 

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

Known to have been used on 1969-1970 air conditioning boxes to hold a vacuum hose to the actuator.  They can be screwed or bolted to the plenum.   Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Inside diamenter = 1"

Used plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used plastic clip for the Mercury Cougar or Ford Mustang.

Used wire loom plastic clip for the Mercury Cougar or Ford Mustang

Used plastic clip for the Mercury Cougar or Ford Mustang.

Partially dipped clip for attaching the seal on top of the radiator core supports. Often times with air conditioning the seals were installed. The factory sometimes used staples, sometimes clips. You would have to investigate your core support for staple holes. 5 clips are typical for attaching the seal. Spread them apart to where it looks equal. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. ...

This is the speedometer cable clip that connects to the firewall and transmission tunnel. Replaces Ford Part # : 373829

Used clip for mounting the vacuum modulator steel line or tube on 1967-68 Mercury Cougar or Ford Mustang with C4 or automatic transmission. Mounts under one of the top bolts where the bell housing connects to the engine block. This is not a reproduced part, that we know of.  The basic Ford part number is 7C072.

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

Reproduction of the plastic square hood insulation clips. 11 used on most vehicles. Sold individually.

Windshield washer hose clip that holds the hose up under the cowl. Concours quality

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Clips that attach to the dash for mounting the defrost nozzles. Package of 4 clips and 4 nuts, enough for non air conditioned cars, same clips used for air conditioned cars. Cars with A/C only need 3 clips installed though. Nuts are different than OEM, but work fine, we suggest adding a flat washer though.

Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...

Fits 1967 and 1968 Standard or XR7

Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.

Prepare to be disappointed... This is a reproduction 1967 - 1968 Ford Mustang clock knob and set screw (replaces Ford part # C7ZZ-15032-A) that can be cut down to work on your 67-68 standard Mercury Cougar (barely). The pictures below will guide you on this "adequate at best" solution for those of you missing this hard to find knob and set screw.Click on images to enlarge. The above picture is a good used original Cougar knob mounted on a 68 clock.  We do not have these original Cougar...

Reproduction thermal fan clutch that fits 1967 - 68 289 engines, 1968 302/390/427/428CJ engines, and 1969 351W engines, all with original Ford thermal cooling fans. Slightly larger in overall diameter, (still fits fine), and retains the correct spacing from radiator. We know that these will fit Mercury Cougar and Ford Mustangs 1967-69. Closest reproduction fan clutch on the market that fits the original and reproduction C8OE-B 7 blade power fan. Hayden fan clutch with an overall height of 2.98...

C7ZE-8A616-B For all 1967 - 289 engines with air conditioning (fan marked C6OE-G), and all 390 engines (fan marked C6OE-F), without air conditioning. Fan clutch marked C7ZE-B on the hub. Ford part number C7OZ-8A616-C. Ford Motorcraft number YB-107. Good used clutch, we are unable to warranty these units.

C7ZE-8A616-A Application is 1967 S code 390 with air conditioning. Marked C7ZE-A on the hub. Ford part number C7OZ-8A616-A. Ford Motorcraft number YB-106. Good working clutch, we are unable to warranty these units.

(7521) The attaches to the bottom leg of your equalizer bar and the pointed end fits into the recess of your clutch fork. Replaces Ford Part #: C7ZZ-7521-L.

Core used set of Eaton clutch brushes, we save these because of the FoMoCo stamped bracket with Ford part number C7AA-2979-A. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to reproduction version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for NEW Eaton brushes. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

This set of brushes only fits the Eaton brand of air compressor clutch. These are exact reproductions made from the original tooling. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to this version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for core brushes with stamped Ford numbers. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

Equalizer bar or "Z" bar for small block engines with a manual transmission. Both 3 and 4 speed manual transmissions. Replaces Ford part number C7ZZ-7528-G.

Nice reproduction of the original. Street name is Z-Bar. For all 1967 - 1970 FE engines 390 and 428CJ. Replaces Ford part #: C7ZZ-7528-B.

Clutch equalizer pivot mount, engine side. Zinc plated. Replaces Ford part #: C7ZZ-7A572-BR.

Mounts on frame for equalizer bar to ride on. Replaces Ford Part #: C5ZZ-7507-A.

Replaces Ford Part # : C7ZZ-7507-B

C5OZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long. Specifically used with a 157 tooth flywheel, as opposed to the 164 tooth fly wheel used after Feb 1968.Replaces ford Part # C5OZ-7515-B.  Cougar before 2-15-1968, 289/302 Engines.  Mustang before 2-15-1968, 289/302 Engines. *Note - This style of clutch fork uses the 'wire' for the holder, not the clip. ...

C5OZ-7515-B Manual transmission clutch fork for small block V8 engines - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long from the divot where the rod rides to the tip of the forked end. Specifically for the C5DA-6394-A bellhousing that used a 157 tooth flywheel. Cougar 1967 through 2-15-1968. XR7, XR7-G. Mustang 1965 through 2-15-1968. 2+2, GT. Fairlane 1965 through 2-15-1968. 500, XL, Custom. Torino / Ranchero 1968 through 2-15-1968. 500, XL Comet 1965 through...

Used until early (prior to 2/15/1968) on manual transmission cars. Comes with rivets. Replaces Ford part #: B9AZ-7522-B.This style uses the early clutch fork with the anti rattle wire.

Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is a 10 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.

Manual transmission clutch kit for all 1967-69 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 390 engines. This is a 11 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.

This pedal assembly is a copy of the 1967 clutch pedal. It can be used on 1968 with no modifications. Fits all engine applications. Has replaceable shaft as shown. Replaces Ford Part #: C7ZZ-7519-A.

C7ZZ-7519-A We also offer used clutch pedals along with our quality reproduction 1967-1968 clutch pedal. These pedals will no doubt show some wear around the clutch rod holes. Three and four speed pedals are all the same. Mustang is the same too.