1967 Ford Mustang

Original used speaker lead wiring harness pigtail for all 67 - 68 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the kick panel.*Note - The only difference between this pigtail and the one listed for the 1969-70 dash speaker is the actual plug design.

Used under dash wiring harness repair plug and pigtail for the neutral safety switch / back-up lights and engine feed harness for the LATE 1967 Mercury Cougar. Works for both standard and XR7. This is part of the 14401 main under dash wiring harness.*NOTE* The blue/red to yellow/black wire is for the radio feed. The only difference between the early and late harnesses, is the early harness has an extra blue wire.

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Original used AM radio power lead wiring harness pigtail for the 67 - 71 Mercury Cougar and Ford Mustangs with factory AM radios. This double male plugged wiring pigtail solders to the your factory Ford AM radio. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios.

Reproduction wiring harness pigtail plug for the 67 - 68 Cougar or Mustang voltage regulator.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your radio. Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door...

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Reproduction under hood wiring harness repair plugs and leads that go from the under hood harness to the starter solenoid on the Mercury Cougar or Ford Mustang.  Sold as a pair.

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Unique rubber sealed plug, 1967 single pin only. Violet colored wire. Fits 1967 Mercury Cougar and Ford Mustangs.

Correct plug for your 67-71 AM- FM radio, or 8-track... Often these have been cut from the main loom to install an after market radio.The 1972 model used the same plug, but the wires are not in the same spots, go figure! These are speaker wires not power wires.The color codes are:  White right cowl speaker.   Orange left cowl speaker. Speaker blue / black ground. Power "not this listing." Blue / red stripe, radio light. Yellow / black stripe, power in for radio. ...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

Reproduction engine side stud for the clutch equalizer bar or z-bar that fits a 289, 302, 351W, or 351C engines in the 67-70 Cougar or Mustang. 

NOS 1983 Ford manual on how to read and understand vacuum diagrams. Although it's technically made for older cars, it has tons of useful information on how to decode diagrams. Includes sections on vacuum theory and applications, devices, hoses, schematics and system diagnosis. This handy book has information pertaining to how the engine creates vacuum, the carburetor and it's vacuum pressure regulation characteristics as well as air intake, fuel induction, emissions and ignition. As an...

Used A/C floor duct for 67 - 68 Cougars and Mustangs with a console. Grade B vents will mostly have a missing metal bracket and / or small crack or break usually around the mounting holes.

Concours correct A/C discharge hose for Mercury Cougars and Ford Mustangs.Replaces part # C7AZ-19972-A or C7ZZ-19972-A.This hose is compatible with both 134a and R12 refrigerants.

Concours correct A/C sight glass hose with a 90° fitting for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

For 1967-68 Mercury Cougars and Ford Mustangs with the 289 or 302 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C7AA-2981-F.

Used pulley and clutch assembly for Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-H.

For 1967-69 Mercury Cougars and Ford Mustangs with the 390 engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-3/4", a clutch diameter of 6", and an overall thickness of 2 inches. Whew, say that 5 times fast!Ford part # C7SA-2981-A.

For 1967 - 1969 Mercury Cougars and Ford Mustangs with the 390 or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-11/16", a clutch diameter of 6", and an overall thickness of 1-5/8 inches. Whew, say that 5 times fast!Ford part # C7AA-2981-J.

This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and tested vacuum tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's too. We also stock a Grade B version that looks the part, but does not have a working check valve, and will still need a new rubber coating on the...

Original retainer for the passenger side A/C vent on Mercury Cougars and Ford Mustangs with equipped with factory A/C. Necessary for correctly installing the upper fastener of the vent.Ford part # C7ZA-19A950-A.

This is a blemished piece that we're offering at a discount. We received a shipment of these vents with some issues with the chrome finish. The flaws are visible in direct light but probably not noticeable when installed. Fit and function is the same as our premium units. See example photo for a closeup of the imperfect chrome finish.This reproduction A/C vent register with knobs is a perfect fit for your Mercury Cougar or Ford Mustang / Shelby. Includes all three control knobs. *NOTE* Mustang...

Grade A used passenger side air conditioning vent register for 1967 Ford Mustang with standard (non-deluxe) interiors. This one has the factory pebble grain or camera case finish. Very nice used, only have the one available. We also have several Mustang center vents available with the pebble graining.Replaces Ford part number C7ZA-19893. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

This new reproduction is a spot-on replica of the 1967 passenger side AC vent! It differs from 1968 only in that 1968 used a break-away vent that was very prone to failure. This is a fixed, one piece body and will not fall apart. This will be a direct fit to your 1967 and 1968 Ford Mustang with no modification needed. Dealer pricing available. *NOTE* Mustang used the shorter version of this vent than the Cougar did, otherwise they are visually and mechanically the same. Click on images to...

Normally we do not list Mustang specific parts, but since we are the distributor for these new reproductions, we need to have them accessible via our web site to all. This kit is the same as a Mercury Cougar set with the exception that the passenger side is shorter on the Mustang / Shelby than the Cougar. Top quality chrome finish and precision fit worthy of the most scrutinized restoration. Remember when we used to spend hundreds of dollars for "decent" used examples and then take a risk with...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service,...

This adapter is threaded on bottom for PCV valve and 6 degree angled 5/8" nipple on side. Was gold Cadmium plated, not painted. Original Ford part number C7OZ-6A706-A.

3M brand weather strip adhesive for installing the various rubber weather stripping found on Mercury Cougars on all years. This is the black colored adhesive and is the 5 ounce size.

Used alternator adjusting bracket for any 1967 Mercury Cougar or Ford Mustang with 390 engine and without smog. Also fits Shelby GT-500.Replaces Ford part number C6AE-10145-B, or it is stamped C6AE-B

1967 289 smog pump adjusting arm, casting number C6OE-9B452-A. Ford part number C6OZ-9B452-A. Application is most Ford and Mercury cars sold new in California in 1966-67. Mercury Cougar only used this thermactor pump adjusting bracket in 1967.                                          ...

1967 390 smog pump adjusting arm, casting number C7AE-9B452-A. Ford part number C6AZ-9B452-C. Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird so there are a few minor differences when compared to a 1967 Mustang or Cougar but the mounting of brackets and belt alignment are the same. Click on images to enlarge.                                       The...

Ford called this part a 'sleeve'. Attaches to the lower shifter arm with a hitch pin. Has nice bushing, with correct nut, washer, and pin. The 1967/68 and 1969/73 versions are identical. The C1AA-7353-C sleeve has fine threads, the C9OZ-7353-A has course threads. Fits all 1967-73 Mercury Cougar and Ford Mustang, and we suspect many other Ford vehicles beginning in 1961. This fine thread version is hard to keep in stock, consider the 1969-73 course thread version as an alternative. Check out...

Nice used California emissions air cleaner assembly, includes base with elbow, snorkel, heat riser and air cleaner lid. Application is any 1967 Mercury Cougar or Ford Mustang with C code 289-2V or A code 289-4V engines with closed emissions as sold in California. Elbow on air cleaner connects to the oil fill cap with a rubber hose. All good parts as shown, thermal switch in air cleaner snorkel may not work, and no we cannot test them.Even if you are not currently running all original parts...

Fits all V8s with oval air cleaner.

[No Description Provided]

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

Four per car unless you have a 1968 decor or standard model that has the unique three hole armrest and then you will need six. Replaces Ford part # C7AZ-6224146. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Rear axle assembly - Housing, Axles, brake backing plates, and third member. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. 1967 early 9 inch rear end housings had the carry over fill plug in the steel housing as seen from the back of the car. As removed from West Coast Cougar organ donor car. We recommend a bearing...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1967 late 9 inch rear end housings without fill plug in the steel...

Original New Old Stock NOS reverse light lenses. Sold as a pair, includes screws!Ford Part number C5ZZ-15514-A.

These Back-Up Lamp Lenses are exact copies of the originals which come with the FoMoCo Logo. Sold Individually. Includes screws!

Correct for closed emission system Cougars sold only in California. Air cleaner base for both the 289-2V and 289-4V engines. About 17.25" inches in diameter. California emissions with the metal elbow for hose connection to the oil filler cap.

Factory air cleaner base the all S code 1967 Mercury Cougar non-GT or the 6.5 Liter option, 1967 Mustang 390-4V without the GT option, and 1967 Ford Thunderbird with Z code 390-4V or Q code 428-4V engines. California emissions version which has the closed emissions. Note the elbow on the side which attaches with a hose to the oil fill cap.This is the one everyone uses to make a correct 1969-70 428 Cobra Jet ram air or 1967 GT air cleaner base . This basic bowl design was used by the Ford...

Reproduction group 27 battery heat shield that fits many Mercury Cougar and Ford Mustang applications from 1967-70, on most hi-performance engines. It was often the first part discarded but serves a real purpose. Nice American made part, stamped with Ford numbers C7ZB10A682B and C7OB10A682B. There is also a D0... sized for group 24 heat shield offered for 1970-73. *Trivia - these battery heat shields were often trimmed down to fit group 24 batteries.Click on the link below to find some...

Good used tray that is not currently reproduced. Most people prefer the group 24 battery but for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting). Many that are not rotted have been cut to accept a group 24.