1967 Ford Mustang

The trim at the top of the windshield on the left hand side.Ford part number C5ZZ-6503145-B

NOS driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503137-B.

Your original decades old trim will look fine... Until you place it next to a quality paint job.Ford part number C5ZZ-6503137-B.

Used driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. These are suitable for restoration and for use your daily driver.Ford part # C5ZZ-6503137-B.

This restored OEM stainless steel lower windshield moulding / trim has been restored to a level far beyond NOS. It has been polished to a mirror like finish that is brilliant and gleaming. The term "over restored" could be applied to this part because back in the day FORD never spent the time we invested into polishing this piece. Original parts like this one always fit and look superior to "offshore" reproductions.Ford part # C5ZZ-6503148-B.

This good used original lower windshield moulding / trim has been carefully inspected to be free of small dings and heavy scratches. It will have very light scratches consistent with a classic of this age but nothing a do it yourself type could not bring to show quality on his own. This trim piece is perfect for someone wanting a trim part ready to install on their very nice driver or occasional show car. Much better fit than "offshore" reproductions. Ford part # C5ZZ-6503148-B. *NOTE* Keep in...

NOS passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503144-B. 

Restored passenger side (right had) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will look right at home gleaming in the sun on your mint condition Cat or Pony and will definitely make your ride POP!Ford part # C5ZZ-6503144-B.

Used passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece is suitable for your lower quality daily driver or a great piece for a high quality restoration.Ford part # C5ZZ-6503144-B. 

Restored passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece is considered over restored because of the high luster and will make your Cat or Pony absolutely POP!Ford part # C5ZZ-6503136-B.

Used passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will fit right in on your daily driver or is an excellent candidate for those of who like to restore your own parts.Ford part # C5ZZ-6503136-B.

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

Restored five piece windshield trim set has been restored beyond the original luster. Keep in mind only cores with minor dings, dullness and scratches can be accepted. Kinked, gouged, and flattened cores will not be credited. This windshield moulding set fits the 1967-1968 Mercury Cougar as well as the 1964 1/2 - 1968 Mustang Coupe and Fastback. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* If...

Good used five piece windshield moulding / trim set as taken from a parts car. Finish will be dull and some pieces may have minor scratches, but overall, this set is ready to install and will look decent as is. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. ...

Reproduction sway bar mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Original driver side sway bar mount for your 1967- early 1968 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions of this bracket were used starting in 1968. This version has a straight cut edge on the front section, later versions were curved. Straight and curved mixed during 1968 on same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as:...

Reproduction sway bar clamp mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Original passenger side sway bar mount for your 1967- early 1968 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions of this bracket were used starting in 1968. This version has a straight cut edge on the front section, later versions were curved. Straight and curved mixed during 1968 on same car. Original part number is 5A483. The MPC and other manuals refer to this...

This is an OEM original with 3/8"-16 threads. Overall length according to the MPC is 9 inches, with 3-1/4 inches being threaded but we have found almost without fail, the actual length is 8" with 3 1/4" of threads. We also carry the OEM hold down wing nut or spinner nut Mercury Cougar part number B9AZ-1462-A. Additionally, look for the wheel centering plate or disc, part number C5ZZ-1424-A. Item for sale in this section is only the J-bolt.

Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs produced before 1/3/1967. You will have to look very closley to notice the slight differences between this bracket and the later version.Ford part # C7ZA-2882-C, MPC # C7ZZ-2882-B.

Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs produced after 1/3/1967. This bracket was utilized throughout the entire 1968 model year and is also listed as the service replacement part for the early mounting bracket.  Ford part # C7AA-2882-L, MPC # C7AZ-2882-G.

Cast iron pedestal mount for the air conditioning compressor on all 1967 and 1968 cars with 390-2V, 390-4V, or 428CJ FE engines. Mercury and Ford master part number C7ZZ-2882-A, we suspect that this is an error in our 1975 editions of the MPC's. C7SZ-2882-A is what we suspect is the correct number. In any case, C7SA-2882-A is the factory casting number on these brackets.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird, so there are a few minor...

Used alternator bracket for any 1967 Mercury Cougar or Ford Mustang with 289 engine, but without factory smog pump. Replaces Ford part number C6OE-10156-A.*Trivia - the only difference between this bracket, and the C8OE-10156-A bracket is the thickness of the steel. Either one will work on 289/302/351W engines 1966-69.

C5TE-10156-A Alternator mounting bracket for most 1967 Mercury Cougar and Ford Mustang with 390 engine. Ford master part number C5TZ-10156-A. *Note - Excludes cars with California DSO's with smog pump.

Cast iron in construction, there are two slightly different brackets for 1967. This part has a casting number of C7OE-9B450-A. This would be the early bracket for Cougars built prior to 1/3/1967. Must be used with the 1967 style air pump C7AZ-9A486-B. Ford air pump mounting bracket part number C7OZ-9B450-A. *Emissions equipment came on all 1967 Ford and Mercury cars. California DSO's only.

Cast iron in construction, casting number C7OE-9B450-B there are two slightly different brackets for 1967. This would be the later bracket for Cougars built after 1/3/1967. Must be used with the 1967 style air pump C7AZ-9A486-B. *Emissions equipment came on all 1967 Ford and Mercury cars. California DSO's only. Ford air pump mounting bracket part number C7OZ-9B450-B

Original FoMoCo used part in good condition. Casting number is C7AA-3A772-B. Fits both small and big block. This is really the way to go... Original OEM FoMoCo with all the right markings and about half the price or repro. Ford Part #: C7ZZ-3A732-B.

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.Not for use on 17-20" wide standard cooling radiators. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on...

Ninety degree bracket needed to mount the starter safety switch to the column tube in 1967.

One year only, 1967 390 only used brackets for use in conjunction with original 1967 radiator. If you are putting a reproduction radiator in your 1967 then the 1968-1970 lower brackets are what you are after. Check out our video on Radiator and Fan upgrades below: ...

Concours correct reproduction of the front sway bar clamps used on all 67 - 70 Cougars and Mustangs with the competition suspension option, or 15/16th" sway bar. Never available until now. Exactly like the originals in every detail. Standard for all Shelbys, Boss 302s, and Cobra Jets. Stamped and formed just like the originals.

Repro fuel pump gasket for 1967 - 1970 Cougars or Mustangs with 289/302/351W/390/428CJ engines.

Used on big block radiators, unique to 1967. Sold as a pair. Replaces Ford part number C3AZ-8125 Check out our video on Radiator and Fan upgrades below: ...

Used on the lower mounts on the 67 - 70 big block and small block 24" wide radiator. A 1967 390 with the original radiator uses a different lower mount system which uses a different sized insulator. If you are updating your 67 with a 68 radiator you will need these. Sold as a pair. Replaces Ford part #: C8ZZ-8125. Check out our video on Radiator and Fan upgrades below: ...

Sold as a pair, fits well into your upper radiator bracket used on 24" radiators 1967 - 1970. Replaces Ford part #: C7OZ-8124Check out our video on Radiator and Fan upgrades below: ...

This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

We rarely have extras of these in stock but we like to show these items so you know what you are looking for or you can use it as a visual and fabricate your own kit. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice.Also available as a reproduction mounting kit. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them. ...

Nut for attaching brake boosters in any 1967-73 Mercury Cougar or Ford anything, including Mustang. 3/8 - 16 zinc plated nut with serrations.

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Replaces Ford part # 55806-S

Used mounting plate for the heater blower motor on the 67 - 68 Cougar or Mustang without A/C.

4" mounting Plate for Standard Spare Tire. Replaces Ford Part #: C5ZZ-1424-A.

3 1/8" Style Steel Wheel Spare Tire Hold Down. Available in Black or Chrome. Ford Master Parts Catalog indicates that this hold down was found on some 68 and 69 Cougars with SS Wheels. You may need to bend the ears in slightly to get them to fit properly inside the hole in the center of the wheel. Replaces Ford Part #: C8MY-1424-A.

Sold individually. Phosphate & Oil (gray-black)

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!