1971 Mercury Cougar

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971 Mercury Standard model Cougars and all Ford Mustangs with 22 gallon fuel tanks. This is an original 1971 fuel sending unit that has a return fuel line, and with two electrical prongs. Ford casting number D1ZF-9275-B, master parts catalog number D1ZZ-9275-B. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971-73 Mercury Standard model Cougars and all Ford Mustangs with 22 gallon fuel tanks. This is an original 1971-73 fuel sending unit with two electrical prongs. Ford casting number D1ZF-9275-AB. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar XR7 models with low fuel warning light. The sending units with low fuel have 3...

Used in-tank, fuel sending unit without the low fuel option. Tested and cleaned units for all 1971 Mercury Cougar XR7 with 22 gallon fuel tanks. This is an original 1971 fuel sending unit that has a return fuel line, and with 3 prongs (2 electrical and 1 alignment prong). Ford casting number D1WF-9275-B, master parts catalog number D1WY-9275-B. This unit comes with a new 3/8 inch filter, brass float, and sending unit gasket. *Note - Not compatible with Mercury Cougar Standard models without...

C8OZ-14A033-C Brass clip with accessory terminal for attaching the accessory lead wire with multi connector. Missing attaching screw and nut. Attaches to all 1969-73 fuse blocks found on Mercury Cougars and Ford Mustangs. Accessory feed terminal for such things as 1969 swing away steering column, rear window defogger, speed or cruise control, etc. Includes fuse block mounting hardware.*Note - Naked, no machine screw and nut for mounting to fuse block. 

This is the correct, original gasket for your 1971-73 Mercury Cougar antenna. Not only is it much thicker than the Ford Mustang gasket, but it also has a different overall geometry to it. Gasket mounts under the antenna base, The Mustang gasket will work, but your antenna will always be slightly askew. Unfortunately the high quality reproduction antenna we offer is only available from the manufacturer with a reproduction Ford Mustang gasket. Please remember not to discard your original Cougar...

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

Rubber oil pan gasket for the 351 Cleveland engine in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 2 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-2V engines. This gasket set includes a metal pan gasket.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-4V Cleveland engines. ...

Premium quality 2-1/4" Diameter Black / Pearl Shift Knob. Graphics are subsurface and can not wear off. This knob has a 16mm x 1.5 brass Master Insert and comes with a Standard Thread adapter kit which includes one reducer and jam nut in each of the following sizes: 5/16-18, 3/8-16, 3/8-24 and 1/2-20. Made in the USA. *NOTE* Each Pearl style knob has its own unique pattern. The knob that you receive will vary somewhat from the knob shown in the photo.Check out this video f our 2013 Open House...

1967-1973 14 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for courtesy, instrument cluster, door, map, glove box, pillar, luggage compartment, and clock lamps. Also for the lighter, ignition key on and head lamp on buzzers.

This grille will be less than perfect with one or two cracks, bend showing and pitting. A Grade "B" will not be cracked around the perimeter and will not be missing any pieces. Good for a driver quality car. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in...

This grille will be less than perfect with one or two cracks, bend showing and pitting. A Grade "C" WILL be cracked around the perimeter, but will not be missing any pieces. Good for a driver quality car.

Used hairpin clip for attaching the brake light switch to the brake pedal. This clip was also used to attach the clutch rod to the clutch pedal on manual transmission cars. Fits all years 1967-73, Ford and Mercury.

Correct for any 1967-73 Ford product with a tilt or fixed column. The repros are fine, but the end knob is distinctly different. Extremely difficult part to find in NOS form and very sought after. Keep in mind we also have excellent used pieces at a fraction of the cost. Ford part # D0AZ-13305-A.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Used grade "A" emergency / parking brake release handle with bezel and cable for the Mercury Cougar. This unit fits both the Standard and XR7. Our grade "A" part will have a good cable sheath and the chrome on the release handle will be very nice, but not perfect. Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web...

1971 *351-4V after 4-12-1971. 1971 429 CJ. 1972 with "Sporty" dual exhaust. Engine designated as a 351-CJ on air cleaner lid. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-D. *Late production - after April 12, 1971.

1971 *351-4V prior to 4-12-1971. 1972 and 1973 351-4V with "Quiet" dual exhaust. Holds the rear of the muffler to the underside body. Ford part number D1WY-5260-B. *Early production prior to 4-12-1971.

Mounts to the frame on the left side of the fuel tank. Supports and holds the rear of the tailpipe stationary. 1971 all 351 and 429CJ with dual exhaust. 1972 all 351 with "Quiet" and "Sporty" dual exhaust. Ford part number D1ZZ-5260-E. *Pipe clamp D1AZ-5A231-C needed 2" diameter pipe "Quiet". *Pipe clamp D1AZ-5A231-A needed 2-1/4" diameter pipe "Sporty".

High quality, durable canvas cap with velcro closure. The hat now features our Web address on the back! "The baseball cap arrived Saturday but since I wasn't home, they didn't leave it for me. I picked it up today at the post office. It's real nice! Seems to be a higher quality cap compared to others I've worn. Thanks for sending it." Larry Check out this video of our 2013 Open House event! ...

Reproduction 4002 incandescent (non-halogen) low beam light bulb for the 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar. Plugs right in to the factory 3-prong plug and mounts in the outboard position on the car.These are close to OEM wattage (37.5 / 60 watt, OEM was 37.5 / 50 watt) to work with the factory headlight switch, without adding any relays like you would for higher wattage halogen bulbs.Ford Bulb #: 4002, Aftermarket Bulb #: 4000. Sold individually, 2 required per car. ...

The 1971 - 1973 Mercury Cougar XR7 came with Tier and standard came with Perforated headliner, so make sure you choose the correct texture. All of the colors with the exception of Dark Green and Dark Blue are available in either texture.Check out our video below showing how to install one of these bow-type headliners. This was done by a pro, but it's a job you can do yourself with some patience and basic knowledge. ...

These stainless steel tubes are made to exact O.E.M. standards and specifications. All choke tubes have the proper fiberglass insulation, fittings, rubber hose, and S-clip.

These steel tubes made to exact O.E.M. standards and specifications.

D1AZ-9A603-A Metal shroud for all 1971 351 engines including H code 351-2V and M code 351-4V. One piece design uses a paper and aluminum tube to bridge to the air cleaner snorkel.

D1AZ-9A603-C Metal shroud for all 1971 429 Cobra Jet engines including C code 429CJ non-ram air and J code 429 CJ with ram air. One piece design uses a paper and aluminum tube to bridge to the air cleaner snorkel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested...

New old stock hood bumper for any 1971-73 Mercury Cougar or Ford Mustang. Sold individually, limited to stock on hand. Replaces Ford part #D1ZZ-16758-A

This kit is the same Scott Drake "Shelby Style" DELUXE hood pin kit offered by many other vendors.Kit includes 2 Hood Pins, 2 dowel pins, 4 Nuts to hold the dowel pins on, plates for the top of the hood, 8 screws to hold the hood plates on and 2 tie down cables. The difference between the standard version and this deluxe version, is that the standard is chrome plated and the deluxe is stainless steel. Common consensus is that the holes for the pins were hand drilled at the factory, so the...

This is an extremely rare hood scoop found only on the 71-72 GT and 1971 429 Cougars. This is similar to the 1969-70 scoop, but tapers more in the front so as to follow the unique hood line of the 1971-73 Cougar.Ford part # D1WB-16C664-AA. ...

Black paper wrapped aluminum flexible tube that connects the vapor canister to the air cleaner. This is as close to concours as we can find, 3/4 inch diameter, 36 inches long, and black outside, brown paper color inside.  Fits 1970 California Delivered Cars and all 1971 - 1973 Cars. Look for Buck Tag EV or EM. Preheat/Emission Control Duct. Replaces Ford Part #: D1UZ-9d667-A, D4HZ-9d667-A or D0AZ-9D667-A

C9AZ-6A664-A Original used hose that connects the valve cover oil cap mounted PCV valve and the front of the Quadrajet carburetor base plate on 1970 through 1971 Mercury and Ford 429 Cobra Jet engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work)....

Used connector plug that attaches to the A/C vacuum switch assembly on the 69 - 72 Cougar or Mustang. The six vacuum hoses are molded into the plug, and for those instances when someone has cut a hose, simply use a hose connector.

Good used power steering pressure line hose retainer. Mounts on top of the shock tower brace as shown. Comes as shown with used rubber insulator. Fits all 1971-73 Mercury Cougar and Ford Mustangs with V-8 engines. Ford part # D1ZZ-3C510-A.

Used grade A near perfect dog dish style hubcap / Wheel Cover for the 1970 Mercury Cougar Eliminator. This same cap was standard equipment for the 1971-73 Mercury Cougar and was used with dealer installed trim rings when the optional 15x7" wheels were ordered on 1971-72 Cougars. There were two versions for this cap, one had a brushed finish where the other had a bright finish. These are all driver quality with some dings and or scratches. The one pictured is brushed, but we often have both in...

Used grade B less than perfect with a couple dings / scratches / blems dog dish style hubcap / Wheel Cover for the 1970 Mercury Cougar Eliminator. This same cap was standard equipment for the 1971-73 Mercury Cougar and was used with dealer installed trim rings when the optional 15x7" wheels were ordered on 1971-72 Cougars. There were two versions for this cap, one had a brushed finish where the other had a bright finish. These are all driver quality with some dings and or scratches. The one...

Used A grade dog dish style hubcaps / wheel covers for the Mercury Cougar as well as other Mercury and Ford products. Used item as would have been found on 1969 Eliminators as well as other models with the plain poverty or dog dish center cap, about 7-1/2 inches in diameter. Replaces Ford part # C8OZ-1130-G, or C8MY-1130-A. Fits: 1969 Mercury Cougar Eliminator / Cyclone1970 Mercury Cougar Eliminator / Cyclone1971 Mercury Cougar / Cyclone1972 Mercury Cougar 1973 Mercury Cougar 1969 Ford Mustang...

Used grade A near perfect dog dish style hubcap / Wheel Cover for the 1970 Mercury Cougar Eliminator. This same cap was standard equipment for the 1971-73 Mercury Cougar and was used with dealer installed trim rings when the optional 15x7" wheels were ordered on 1971-72 Cougars. There were two versions for this cap, one had a brushed finish where the other had a bright finish. These are all driver quality with some dings and or scratches. The one pictured is brushed, but we often have both in...

Used grade B less than perfect with a couple dings / scratches / blems dog dish style hubcap / Wheel Cover for the 1970 Mercury Cougar Eliminator. This same cap was standard equipment for the 1971-73 Mercury Cougar and was used with dealer installed trim rings when the optional 15x7" wheels were ordered on 1971-72 Cougars. There were two versions for this cap, one had a brushed finish where the other had a bright finish. These are all driver quality with some dings and or scratches. The one...

The Hustler Stick features heavy-duty 1-1/4" diameter tubing, and is an alignment bar designed for bumpers, hoods, decks, panels etc. Made in the USA, it has a 1/4", 6 foot long chain with hooks at each end. This versatile tool is very useful in shaping damages on a vehicle body. To use it, hook it up to the panel or bumper, anchor the stick properly, and pull it by hand.We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged...

Fits all 1971-73 Mercury Cougar and Ford Mustang with factory power or manual steering. Rarely did these last 60,000 miles. To find one after 50 plus years is quite a find! These are intended for professional restoration with new bushings prior to installation. That is why they are graded as "CORE GRADE". Very limited quantities, we offer core grade suspension parts for those car owners that wish to avoid reproduction parts.  Original Ford part number D1ZA-3355-A. Anghel Restorations...

Idler Arm Assembly for 1971-1973 Cougar and Mustang. Fits all 1971-1973 Cougars and Mustangs with manual or power steering. Complete with bushings installed and ready to bolt on. Does not include Zerk fitting. This Idler arm helps stop that floating feeling going down the road. Please see the installation photos below. Easy to install. 

This reproduction emergency / parking brake idler bracket welds to the under side of the floor on the driver side (left hand) of the vehicle and has the factory spec pin.

Looks right and it works, but belt alignment will be off. Needs about 1/8 inch of shim to align with the other pulleys. See pictures. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc. This is a...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Used bracket and pulley assembly with new installed bearing for Mercury and Ford equipped with the 429CJ, 429, and 460 engine. This assembly was also equipped on the 1970 - 1971 Torino, Ranchero, and Cyclone with the 429CJ engine. Also many other 429 / 460 engines. Listed in the Ford Master Parts Catalog (MPC) as D0AZ-8678-B. *Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for...

Ignition housing / cover for the fixed steering column on 71 - 73 Cougars and Mustangs. Technically called a "Flange", the ignition cylinder sits inside this cover.This item will need to be re-painted to match your column.Ford Part number D0AA-3511-CW

Good used actuating rod for the ignition switch on the 1971, 1972 and 1973 Mercury Cougar or Ford Mustang. 8-1/8 inches on rod center long.

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use after nearly 40 years.