1971 Mercury Cougar

This eyelet bushing is made from higher grade rubber and unlike the NOS and other reproductions has a solid center shaft. The center shaft of this reproduction is a flat piece of steel that is bent into a circle to make the shaft for the eyelet bolt to go through, just like NOS.  Two per car, these are used on one end of the leaf springs and the shackles are used at the other end. Replaces Ford Part #: C7WY-5781-A, C4DZ-5781-C, C5ZZ-5781-A, D3ZZ-5781-B. ...

New clear plastic lens or face plate for the heater control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can either one depending upon preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

New clear plastic lens or face plate for the air conditioning control on all 1971-72, and early 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to...

New clear plastic lens or face plate for the air conditioning control on all 1973 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. About October 1972, Ford changed the word FLOOR, to HEAT. The lens plates will physically interchange, you can use either one depending upon your preference.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the...

Under dash mounted rear speaker controller. This is a used and tested unit that functions flawlessly. Typically this style of fader switch was used with the stereo radios with either AM/FM or the various 8-Track stereos, with added rear speakers. Included is the blue plug and pigtail that goes to the speakers.The pigtail harness is marked D1AB-19A017-BC.

This is an excellent reproduction made from the original Ford tooling and features the original Ford logo. This is correct for all the cross flow radiators used in 1971 - 1973 except the 1971 429CJ. Opening measures about 20-1/8" in diameter. Replaces Ford part # D1ZZ-8146. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Fan shroud installation kit for 67 - 71 Cougars and Mustangs. Will fit 1971 Cobra Jet shrouds.

Fan shroud hardware kit for the 302 or 351 on the 1971, 1972 or 1973 Cougar and Mustang.

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.

Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.

Fan spacer, measuring 1-1/4 inches, but referenced at 1-9/32" too. Application includes 1971 - 1973 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-20, cross reference to C8YE-8546-A spacer.Ford part # D1OA-8546-AA, Ford engineering # C8YZ-8546-A.

Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.

Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.

Fan spacer, measuring 2-5/8 inches. Application 1972 - 1973 Mercury Cougar and Ford Mustang with 351-4V or 351CJ, and all 1971-72 351's with air conditioning. Reference number YA-75.Ford part # D2AE-8546-AA, Ford engineering # C4AZ-8546-G.

Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.

Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.

Metal fan wheel or squirrel cage for any 1967-73 Mercury Cougar or Ford Mustang with factory air conditioning only. Dimensions 5-3/4 inches in diameter and 4-1/8 inches tall. Shipped used as they come out of the cars, most will need cleaning and have light pitting. Some variations in the stampings, come 'as balanced' from the factory. Comes with allen set screw.

Holds insulation to the firewall. Sold individually, 6 per car. Replaces Ford part # C8ZZ-6501691.

Self threading white plastic. Used on front and rear valances.Sold individually.

Contains nut and washer. Fits all Ford alternators. AMK F-644.

AMK engine fastener kit for 1971 Mercury Cougar and Ford Mustang with J or C code 429 Cobra Jet engines. This kit claims to have 136 pieces. This kit additionally fits 1970-71 Ford Torino and Mercury Cyclone and other variants with 429CJ engine.Kit typically includes: fasteners to attach air cleaner, carburetor, crank pulley, distributor / points / condenser / vacuum advance, drain plugs, engine tag, exhaust manifolds, fan / fan clutch, fuel pump, shroud, ignition coil and strap, intake...

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Reproduction Firewall Insulation Pad Clip Kit for the 1967 - 1973 Mercury Cougar / Ford Mustang

This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.

Used bolts, and usually new washers. Coupe kit comes with 4 - "A" bolts, 4 "B" bolts, and 2 "D" bolts, 12 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang coupes. Coupes or hard tops will have shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded.  There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list...

Used bolts, and usually new washers. Convertible kit comes with 4 - "A" bolts, 4 "B" bolts, 10 new washers. Kit fits all 1970-73 Mercury Cougar and Ford Mustang convertibles. Coupes or hard tops would include shoulder belt hardware. We will make sure these original seat belt bolts are damage free and rust free. The gold finish will be degraded. There were minor and major changes almost every year. We also have hundreds of used belts and belt sets that we cannot possibly list all of, so give us...

AMK strut rod hardware kit, course threaded bolts and nuts with cotter pins as shown.

Grade "B" fenders will have minor rust in the lower portion behind the wheel or minor dents but it will not have both. Please call 503-463-1130 for details. Driver side fender for all 1971-72 Mercury Cougars. B grade sheet metal will need a couple of hours of minor body work performed prior to paint. *Customer Feedback* "The parts are in great condition, just as described! 30 year old metal parts with virtually no rust (not like my parts found in Iowa). Good communication and worked with me to...

Grade "B" fenders will have minor rust in the lower portion behind the wheel or minor dents but it will not have both. Please call 503-463-1130 for details.Passenger side fender for all 1971-72 Mercury Cougars. B grade sheet metal will need a couple of hours of minor body work performed prior to paint. *Customer Feedback*"The parts are in great condition, just as described! 30 year old metal parts with virtually no rust (not like my parts found in Iowa). Good communication and worked with me...

Used upper rear fender brace that brace is visible when you open the door and look in the upper part of the fender void. Welds to the cowl on 1971-73 Mercury Cougar and Ford Mustang. Same tab either side. Ford part number D1ZZ-16A006-A.

Like working on your Cougar's engine? Keep your Cougar's fender from getting scratched with this Cougar fender cover.Check out this video of our 2013 Open House event!

Like working on your Cougar's engine? Keep your Cougar's fender from getting scratched with this Cougar fender gripper. Check out this video

Mercury Cougar left front fender inner splash shield.Ford part # D1WY-16103-A.

Mercury Cougar left rear fender inner splash shield.Ford part # D1WY-16103-B.

Mercury Cougar right front fender inner splash shield.Ford part # D1WY-16102-A.

Mercury Cougar right rear fender inner splash shield.Ford part # D1WY-16102-B.

Sold as a pair. Not only are these usually in poor shape but more times than not they are missing altogether. Great price on a quality, die cut part.

Fuel tank filler cap for all 1971-73 Mercury Cougars. All cars came with emission controls that vented fuel fumes into a charcoal canister. This is a non-vented gas cap.

OEM used not reproduction. Rust and damage free.

Filter / screen for the C6 transmissions, for all 1967-73 and 1967-73 Mercury and Ford. 

Replacement filter for FMX transmissions. Fits all Ford FMX transmissions for any 1969-73 Mercury Cougar or Ford Mustang with that X code FMX transmission. 

Replaceable filter which attaches to original fuel sending unit. Fits 3/8" tube. Replaces Ford part #: D1AZ-9A011-A.

Replacement transmission pan filter and pan gasket kit. For the C-6 (U Code) transmission. Replaces Ford Part Number: C7ZZ-7A098

Replacement transmission pan filter and pan gasket kit. For the FMX (X Code) transmission. Replaces Ford Part Number: C9ZZ-7A098

NOS air cleaner breather element filters for all 1970-73 Mercury Cougar and most all Fords with V-8 engines. This filter fits inside your air cleaner base, a hose connects to the fitting and goes to the PCV valve in the valve cover. Sold as shown, cartridge holder not included.Packaging may vary