1971 Mercury Cougar

Of the many carpets available out there these are the best. That being said they are still nowhere near the quality Ford produced in the day... They are made with the correct 25 ounce Nylon, molded to the contour of your floor pans and have the correct thickness of insulation bonded to the backside. They come with the correct heel pad sewn into the drivers side and have the correct hem in the appropriate places. For a more plush carpet and added sound deadening, don't forget to check our...

Give your Cougar the added comfort of a extra 5/8" of Heavy padding under the carpeting and almost 30 lbs of Sound Deadening material. The mass backing gives your carpet the plush feel of the carpeting in a new luxury car while adding a great deal of sound deadener to muffle road noise. The mass backing combined with the foil heat shield (Part # 10330) should provide sound deadening equivalent to that of the factory sound deadener. Of the many carpets available out there these are the best....

Of the many carpets available out there these are the best. That being said they are still nowhere near the quality Ford produced in the day... They are made with the correct 25 ounce Nylon, molded to the contour of your floor pans and have the correct thickness of insulation bonded to the backside. They come with the correct heel pad sewn into the drivers side and have the correct hem in the appropriate places. For a more plush carpet and added sound deadening, don't forget to check our...

Used fuel tank carriage bolt retainer for the 71 - 73 Cougar or Mustang. This retainer is spot welded under the car to secure the carriage bolt in place when installing your fuel tank straps. 2 required per car, sold individually.

Reproduction castle nut for multiple applications, including the power steering control valve, strut rods, ram cylinder and ball joints on the 1967 - 1973 Cougar or Mustang.  Dimensions: 9/16" - 18.

Used console lid catch. Plastic piece that screws to the underside lid of your late 1970-73 Mercury Cougar or 1970-78 Ford Mustang. Yep, used on Mustang II's, too.  Ford part number D0ZZ-63060A96-B and stamped into the plastic D0ZB-63060A96-B ...

Steering drag link for all power steering and non-power steering Cougars and Mustangs from 1971 - 1973.Replaces Ford part number D3ZZ-3304-A .

Black plastic air conditioning center vent register bezel for any 1971-73 Mercury Cougar or Ford Mustang with Factory installed or integral A/C. Mounts Horizontally in the dash panel. Individual vents roll 360 degrees to blow air straight or to the sides. For that extra level of detail, we suggest using a silver paint pen for detailing the silver edges. Ford part number D1ZZ-19893-A.

Reproduction leaf spring center bolt for your 67 - 73 Mercury Cougar.

Chrome center cap with Red background and chrome Ford logo. Better than original! Original look wheel emblem is made from original dies. This plastic cap is painted and detailed in the original colors. This was never used on any year of Cougar but they do look good!  When using center caps on Legendary wheels, you will need these adapter plates. *Note - Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center...

Reproduction 2 piece spinner assembly for the new HB45 Legendary Series aluminum wheel. The aluminum die cast threaded stem mounts from the back side of the wheel and the chrome spinner truly spins on from the front. Set screw is included to prevent loss. NOTE: Will only fit the HB45 Legendary WheelCheck out our video on Legendary Wheels below: ...

This plastic center cap comes with each Legendary Wheel we sell at no cost. We list them for those that may lose or break one. The overall width is 2 1/2" and they are designed for a opening that is 2 3/8 " wide. Sold individually.Check out our video on Legendary Wheels below: ...

Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a black background.  *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...

Reproduction Cobra GT 350 center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic blue cobra with red detail.  *NOTE - These caps are specifically designed to fit the LW10, LW30, LW50, LW66 and the LW67 series wheels. ...

Reproduction Shelby Cobra center cap for the Legendary Series wheels. This is a modern take on a classic center cap featuring the iconic cobra on a gold background.  *NOTE - These caps are specifically designed to fit the LW10 series wheels.

Reproduction chrome center cap with a black background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* *NOTE* When installing these die cast center caps, keep in mind over tightening...

The price you see is a temporary price reduction due to overstock. Set of 4 Chrome center caps with black background and chrome Mercury Man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and...

Reproduction chrome center cap with a black background and chrome Walking Cat logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Reproduction chrome center cap with black background and chrome Walking Cat logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap...

Reproduction chrome center cap with a blue background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Set of 4 Chrome center caps with Blue background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. The Magnum 500 wheel was not available on the Mercury line-up until 1974 and it came with a red center cap, star-burst pattern, made from plastic. This brand new to the market cap is a great alternative for the many folks wanting to run an attractive, era correct looking...

Reproduction chrome center cap with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. These will work with multiple brands / styles of after market wheels as well. Sold individually.  When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will...

Set of 4 Chrome center caps with Blue background and chrome walking cat logo. These long awaited caps bolt right onto any Magnum 500 wheel with no modifications. They are 2 3/4" at their widest point and 5/8" tall. Fits the following models with Magnum 500 wheels: 1969 Mercury Cougar 1970 Mercury Cougar These will work with multiple brands / styles of after market wheels as well. Sold individually. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain...

Reproduction chrome center cap with a red background and chrome Mercury Man logo for the Mercury equipped with the Magnum 500 wheel. The screw on mounting system on this reproduction cap is far superior to the original clip-on center caps. There are other reproduction center caps out there, but they are not nearly as nice. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate...

Chrome center cap with Red background and chrome Walking Cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer...

Set of 4 Chrome center caps with Red background and chrome Walking Cat logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Reproduction spinner cap for the Magnum 500 Legendary series wheel. Also works with the Magstar II wheel. Each spinner is die-cast with precision and finished in a show quality chrome plating. The exclusive anti-theft retainer plate keeps them in place and secure. A stamped aluminum Magnum 500 emblem and a "Bullseye" emblem are included so owners can choose which one to personalize their car with.Sold individually ...

Officially licensed center cap is an exact replica of the center cap installed on 1966 Shelby 10 spoke wheels. Authentic down to the smallest details. Each die-cast cap features the famous Shelby "CS" race track logo and a show quality chrome finish. The cap is secured in place with a backing plate and hardware to eliminate the risk of it coming lose or being stolen.To be used with the Legendary Series Shelby wheels. Shelby CS LogoFits GT7 - LW10 Series WheelsFits GT6 - LW66 Series Wheels Sold...

Used 2-1/2" standard center cap emblem. This unit looks the same as the 1969-70 version, but is a larger diameter. Ford part # D1WY-1137-A. *TRIVIA* Applique was the industry name for this item back in 1969-70.

Good used console, please call for colors as you will not be getting the one shown in this file photo. The clock and harness is usually missing and the lid will show some amount of wear. The insert will have less than perfect mylar trim but will look great for a driver. The ashtray will also be dirtier than sin. We do offer all the used parts on this console individually but often will not have the color you desire. Keep in mind that we will break these consoles up and sell you only the...

Usually ships in 3-5 business days. Very nice, affordable console that is made from modern, sturdy plastic components. Often times the original consoles are very brittle after years of exposure and will crack easily. The console does not come with a clock but does have a clock delete plate included that can be modified to install gauges or a USB port.

The Mustang and Cougar have identical consoles for the 1971 - 1973 model years. This is a premium quality bezel that houses the clock and surrounds the manual or automatic shifter. They are available in black or natural finish, if you have a color other than black you will want to select "Natural Finish"(click on smaller image too see natural finish). The natural finish is actually black as well but not the "correct gloss" of black. We recommend SEM brand plastic and vinyl paint, available at...

D1WY-17A914-A Rear bumper center beam, mounts on top of the bumper brackets behind the rear bumper.

D1WY-17B883-A Bracket that mounts under the reinforcing beam, lower center bumper mounting point.

Used centering ring for any fixed or tilt column on a 1969 - 1973 Cougar or Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number D1ZZ-18471-A.

Channel bracket cut from a car. This is the front bracket for mounting fuel tank straps on a 1971-73 Mercury Cougar. Mustang may be the same, just not sure. No Ford part number found. We cut it from a car, spot welds of the actual bracket will need to be drilled and cleaned up prior to installation. Make sure that you measure the exact location of this bracket before you remove from your car. 

Correct check valve for both power drum and power disc brake cars. Comes with grommet.

Used transmission line adapter and check valve for all FMX transmissions. This fitting goes into the rear part of the transmission case and connects the rear most cooling line to the case. Has internal ball check valve to prevent fluid from back flowing. All FMX transmissions 1969-73 Mercury Cougar or Ford Mustang. The male threads going into the transmission case are 1/2-20 pipe threads.Replaces Ford part number C3AZ-7D174-A.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

Carburetor choke pull off for most 2V and 4V Autolite or Motorcraft carburetors 1958-74. Diaphragm with a hook on it, to 'pull off' the choke. Ford basic part number is 9J549, part of the dashpot assembly. We do not think that it will fit Holley carburetors. Also fits AMC and Jeep that used Autolite and Motorcraft carburetors. 

Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.

Cigar or cigarette lighter for 1971-73 Mercury Cougar and Ford Mustang. Slight change from the 1970 style, this one has a black plastic shaft. Ford part # D1ZZ-15052-A.

Used 20 amp circuit breaker for either 69 - 70 or 71-73 Cougars.Mounted on the Starter solenoid in 69-70 cougars for convertible tops or power windows, and also on 71-73 Standard Cougars for convertible tops, power windows, heated back light, power seats or seat back release.On the 71-73 XR7 the circuit breaker was mounted next to the starter solenoid on a junction block. Different wire diagrams, owner / shop manuals list this circuit breaker in both locations, possibly due to multiple...

Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

These are used hose clamps that bolt to the body and lateral A/C bracket. These were dipped in a rubber like substance to prevent chaffing. The ones that we have available may have some cracking or damage to this coating. It should be easy to 'dip' them again with the product that is available in most hardware stores. We normally see 2 of these clamps, securing the hoses on most cars. Replaces Ford part number 374125-S100.

This is the correct battery hold down clamp for the 1971, 1972 or 1973 Mercury Cougar & Ford Mustang. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

Factory OEM style clamp for attaching the brake booster vacuum hose to the check valve. Also same clamp for securing the rubber boot to the power steering ram cylinder. Sold individually.