1971 Mercury Cougar

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

These fender emblems look much like the 1968 quarter panel emblems but differ in that they have longer studs that fasten via barrel clips as opposed to a speed nut used on the 1968 quater panel emblems. The Ford casting number on the backside is D1WB-16098-AA. For the money, The 1968 repro quarter emblem is a much better buy . ...

Found on the lower right corner of all 1971 - 1973 Cougars equipped with the XR7 Interior package. Both mounting studs will be in place and it will have a nice overall finish. Ford engineering number as seen on the backside is D1WB-65061A58-AA.

Our used center grill emblems will always have some amount of fade in the plexi area and if the backing has not separated from the rest of the emblem it often times will be lose. We have had good luck filling the backside with epoxy glue. The engineering number as seen from the rear is D1WB-8216-BB.Ford part number D1WY-8A223-B ...

No... Mercury never made an emblem "just" like this one but demand dictated we produce it! This emblem has a 3M adhesive backing and looks and measures just like a 1968 quarter panel script or the front fender script found on a 1971 - 1973. Many people do not like the looks (or price) of the 67 quarter panel emblems so this is a great alternative that does not require you drill holes. The 3M backing is the same found on modern automotive emblems so it will not fall off. Just like our other...

This emblem was located on either side of the quarter panel in 1968 and both front fenders in 1971 - 1973. The studs on the 71-73 were a little longer but this 1968 emblem is an excellent substitute. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very consistent. The plating is very inconsistent on the original Ford emblems. We are very excited to...

This "Stick On" Cougar rear deck emblem was only used on models without the XR7 package. They are often missing as once the factory double sided tape dries out they are often lost forever. We also have a few very nice used examples in stock.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in this picture the line...

High quality reproduction adhesive emblem for your deck lid. Measures 6.5" wide by 2.35" tall. It has the correct black paint applied to the sides. If you have a 71-73 Cougar this chrome emblem is a much better match to your other emblems even though it is not technically correct. We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think...

Reproduction silver walking cat emblem / insert for the 70 Eliminator T shift handle. Often times these little emblems are missing from the shift handle because the adhesive has worn out and the emblem has fallen out and gotten lost. While technically for the 69 - 70 Eliminator, this handle will fit on any 67 - 73 Cougar with the automatic transmission.

Excellent reproduction of the little 1 1/8" wide plastic emblem found on every 1970 - 1974 three spoke steering wheel pad. This emblem can also work on the 1969 - 1973 two spoke steering wheel pad but it is not an exact fit as the two spoke wheel emblem is only 1 1/32" wide. Keep in mind we made these EXACTLY as original so they are very fragile. If you happen to break the emblem anytime within three years of purchasing it we will sell you a replacement for half price when you submit the...

This small sized Cougar emblem (1 3/8" long) was used on 1969 - 1973 Cougars without AC. It was affixed to a block off plate in the very venter of the dash by two peened over die cast studs. It will glue back in place nicely and many Cougar fans have found fun "custom" applications for this attractive piece. This emblem will not be pitted or scratched in any way.

Concours quality, perfect fit and a great value for the money. These little emblems are often the first thing one sees as they approach your car as they are at eye level. These emblems are located on the "C" pillars of your 67 - 68 Cougar but can also be used on a 71-76 Cougar with little or no modification. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Note that if you want to replace these emblems...

Reproduction emergency / parking brake cable return spring for the Mercury Cougar or Ford Mustang. This unit goes underneath the dash of the car and is a part of the emergency / parking brake assembly. Made from the original blue prints to the exact specifications of the originals.Original Ford specs according to the master parts catalog was: 11 1/8" long - 55 CoilsFord Part #: D1ZZ-2A651-A or D1ZZ-2651

NOS emergency / parking brake assembly for the 71 - 73 Cougar or Mustang still in Ford box and never installed.Ford part # D1WY-2780-A.

Used emergency / parking brake assembly for the Mercury Cougar or Ford Mustang and is as removed from a West Coast Cougar organ donor. All parts are inspected and are good and ready for reuse.Ford part # D1WY-2780-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.

Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.

C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

New emergency flasher can for all 1969-73 Mercury Cougars. Not to be confused with the turn signal flasher canister, those are rated differently. 

Reproduction 351 2V AT / MT Emission Decal for the 1971 Mercury Cougar / Ford Mustang

This two part black box is what encapsulates your sequential unit for all years 1969-1973. This of course will work with our reproduction sequential unit as well. This box was designed hang from a hook that is welded to the trunk floor just behind the driver side wheel well. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state...

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

Used engine lift hook or hoist bracket for all 1970-73 351C engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351C-2V and M or Q code 351C-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also...

New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP138 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...

Factory original part for all 1971 - 1972 Cougar hardtops with 351 engines. 1971-72 Mustang with 302 or 351 engines. Left hand bracket. Ford part number D0OZ-6029-B. Does not come with hardware.*Excludes convertible models.

Original 1971 to 1972 hardtop small block or 351 V-8 engine frame brackets. Includes one each: D0OZ-6028-B & D0OZ-6029-B engine frame brackets. These will fit directly into your 1973 Coupe which you can no longer find motor mounts for. Once you place these 71-72 stands in your 73 coupe you can now use the reproduction isolators (motor mounts) commonly available. Does not come with hardware. Also fits 1971-72 Mustang with 302 or 351 engines.*Excludes 1971 - 1972 convertible Cougar and...

Factory original part for all 1971-72 Cougar hardtops with 351 engines. 1971-72 Mustang with 302 or 351 engines. Right hand bracket. Ford part number D0OZ-6028-B. Does not come with mounting hardware. *Excludes convertible models.

Reproduction pair of engine Frame Stands for the 1971 - 1972 Mercury Cougar or Ford Mustang.Replaces ford part numbers: Driver side D0OZ-6029-B / Passenger side D0OZ-6028-B Does not come with mounting hardware. *Excludes convertible models.

After being obsolete for years we have brought back another hard to find clutch equalizer component for 1971-3 Mustang and Cougar. Numerous other Ford application too. Replaces Ford part # C5AZ-7B545-A

Grade A door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar. Very hard to come by without substantial UV damage. Please denote interior color and we will attempt to send your requested color. Product Condition...

Grade B door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar.  Grade B versions will have significant UV damage and will need to be cleaned as best possible and painted. Plastic will be flakey and may be...

Grade B door cup (escutcheon) used on both the Xr7 and Decor / Deluxe interiors with moulded door panels. Casting numbers as seen on the back can read D1WB-6522635-A or D3WB-6522635-A. The last 3 digits will read something like -AWA, AWD or similar which denotes the different colors. These resemble Mustang but are in fact unique to the Cougar. Grade B versions will have significant UV damage and will need to be cleaned as best possible and painted. Plastic will be flakey and may be be...

Very nice reproduction of the drivers side muffler hanger as found on 1970 - 1973 Mercury Cougar and Ford Mustang. Every thing looks correct, riveted rubber and stamped steel brackets as original. You can hang up to a 3 inch pipe with this unit.

Reproduction OEM style passenger side (right hand) exhaust hanger for the Mercury Cougar or Ford Mustang. You can hang up to a 3 inch diameter pipe with this unit.

D1ZE-9431-AA or D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. *351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

D3AE-9431-AA (for 1973) 351-2V Cleveland factory original cast iron exhaust manifold for driver side. Same casting as D1ZE-9431-AA used 1971-72ish.*351C-2V exhaust manifolds only match up to factory 2V intake manifold ports and some aftermarket aluminum cylinder heads, such as one offered by Edelbrock.

Exhaust Manifold Choke Stove Rebuild Kit for All Small Block and Big Block Engines 1967 - 1973. Includes Stainless Steel Mesh Filter Element and Choke Stove End Cap Fitting.

Expansion valve for factory air conditioning for the Mercury Cougar or Ford Mustang.Will work with both R12 and R134 systems.Replaces part #: D1ZZ-19849.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original!Fits 1971-73 Mercury Cougar and Mustang. It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # D1OA-19849-AA. aka YG-27

This extension holds the inner spring tube in place on the 70 - 73 column.Ford part number: D0AA-3790-CW

Ford original eye let bushing 100% correct for the 67-69 Cougar without competition handling, but will fit on any 67-73 cat including those with competition handling. Ford Part #: C4DZ-5781-C.

Poly eyelet bushing that will fit any 1967 through 1973 Mercury Cougar. Replaces Ford Part #: C4DZ-5781-C.