1971 Mercury Cougar

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

New Old Stock rear valance for the 71 - 73 Cougar. Original Ford is the best way to go whenever you can.Ford part # D1WY-6540544-A.

Good used, rust free valance. Getting to be hard to find without excessive filler or severe damage. We have a local body man take small dents out and he does not load them up with Bondo. He removes the filler and works the dent out properly. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do have NOS and on occasion we we get in a flawless used example. We have no plans to start selling the fiberglass reproductions as we feel good used, original...

This is used on cars equipped with factory A/C to stop the flow of warm coolant when the A/C is on. Not an exact replacement, but it will work just fine. Replaces Ford part #: D4AZ-18495-A.

Vacuum tested working hot water valve for any 1969-73 Mercury Cougars or Ford Mustang equipped with factory A/C. This valve stops the flow of warm coolant in the heater hose, when the A/C is on. Has the original cast brass valve and vacuum pod. Used but functional, the reproduction version is very good, but has a black plastic valve, like the service replacement valves from Ford.Replaces Ford part number C9AA-18495-D.

351C VALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1970-1973 Mercury Cougar and Ford Mustang with 351C engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2SZ-6582-A & D2SZ-6582-B. Although we have more of these in inventory, we do not recommend them because the remaining quantities will be less than desireable. *Note - This cover will not work on a 351 Windsor engine. ...

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

CUSTOM ORDER, DROPSHIP ONLY. A top quality replacement vinyl top that looks great and fits perfect. We talked to the manufacturer about making 1/2 vinyl tops, but they said that they would need to charge the same amount for the 1/2 top and all they would do is just cut the top to the length requested, so their suggestion was to just let customers who need a 1/2 vinyl top purchase the full vinyl top and let them cut the top to the exact dimensions for their top.

CUSTOM ORDER, DROPSHIP ONLY. A top quality replacement vinyl top that looks great and fits perfect. We talked to the manufacturer about making 1/2 vinyl tops, but they said that they would need to charge the same amount for the 1/2 top and all they would do is just cut the top to the length requested, so their suggestion was to just let customers who need a 1/2 vinyl top purchase the full vinyl top and let them cut the top to the exact dimensions for their top.

Economy replacement vinyl top that looks great and fits perfect. This economy version top has the fuzzy white backing, not common on the more expensive vinyl tops.

This is an exact replacement for a 1970 remote sport mirror. Nearly indistinguishable from a 1968. Obviously a larger ball and longer than found on 1969, 1971-73 remote mirrors. This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety...

Used seat belt bolt washer for the Mercury or Ford.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

NOS Water bypass plate for all Ford 351C engines. This is an original in the package brass restrictor plate for 1970-73 Mercury Cougar or Ford Mustang Torino etc.Limited to stock on hand. Replaces Ford Part number D0AZ-8K517-A. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

NOS new old stock driver side (left hand) horizontal quarter window outer weather strip. This is just the one outer weather strip that attaches to the body or XR7 convertible moulding. This rubber piece is included in our reproduction Standard or XR7 convertible belt line kits for 1971-73 Mercury Cougar. Ford part number D1WY-7629733-A.

NOS new old stock passenger side (left hand) horizontal quarter window outer weather strip. This is just the one outer weather strip that attaches to the body or XR7 convertible moulding. This rubber piece is included in our reproduction Standard or XR7 convertible belt line kits for 1971-73 Mercury Cougar. Ford part number D1WY-7629732-A.

Restored driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weather strip. Shipping...

Restored passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weather stripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip....

Very rare trim ring used in conjunction with a 15x7" steel wheel and small hub cap on the 1971 Cougar 429 CJ. Only a hand full of Cougars ever got this trim ring. This would also have been used on a few applications like a 1970 BOSS Mustang or 1971 429 Cobra Jet Mustang, Torino or Cyclone. Grade B will show minor scratches and wear.

Very rare trim ring used in conjunction with a 15x7" steel wheel and small hub cap on the 1971 Cougar 429 CJ. Only a hand full of Cougars ever got this trim ring. This would also have been used on a few applications like a 1970 BOSS Mustang or 1971 429 Cobra Jet Mustang, Torino or Cyclone. We have various condition used rings at a reduced price as well, call for availability, sold individually.

Made by Trico who made them originally for Ford. Replaces Ford part #: D1ZZ-17528-A. Sold individually

Plugs into firewall and connects original style oil pressure sending unit, water temperature sending unit and coil. Fits all 1971 Mercury Cougar and Ford Mustang with 429CJ engines. Replaces Ford part number D1AZ-14289-D.Check out the video below on our new gauge tester: ...

D1ZZ-15525-A 71 72 73 Mercury Cougar and Ford Mustang with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Good Used Clock Harness for the 1971, 1972 or 1973 Mercury Cougar or Ford Mustang Mach 1. Wiring harness, or pigtail that goes from the back of the clock to the main under dash wiring harness, and ashtray light socket and shroud. The Mustang wiring harness for the clock generally does not include the light socket for the ashtray. The MPC indicates that the Mach 1 did receive this Cougar wiring harness. Ford part number: D1WY-15A006-A and D1WB-15A006-A.

Factory used and tested under dash wiring harness for all 1971 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This harness plugs into the speaker plug of the radio, and connects the door panel wiring harness with door speaker option in a 1971 Mercury Cougar or to the A pillar post where it connects to the door wiring harness that has the speaker plug for the door mounted speakers in 1971 cars. White speaker wire goes to the passenger side speaker, and the...

Wiring harness for double prong fuel sending units on 1971-73 Mercury Cougar and Mustang standard models without low fuel warning lights. This harness has two wires which attaches to the two prongs on the D1ZF-9275-AB fuel sending units. Ford part number is D1ZB-14406-B or D1ZB-14406. *Note - Standard cars with low fuel sending units have three prongs and three wires on the detachable pigtail.

Wiring pigtail for the low fuel sending units on 1971-72 Mercury Cougar XR7 and standard models with low fuel warning light. The Safety Convenience Package included a low fuel warning light. This pigtail has three wires which attaches to the three prongs on the D1WF-9275-AC low fuel sending units. Ford part number is D1WB-14406-B or D1WY-14406-B. *Note - Standard cars without low fuel sending units have two prongs and two wires on the detachable pigtail. 1973 is also different, it has moulded...

This pigtail fits left or right rear quarter power window switches and motor. Taken from an original used harness that had a Ford part number of D1ZB-14644-AB

Used wiring pigtail that runs from the under dash harness to the radio on the 71 - 73 Cougar.

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Works on late 1970 - 1973 Cougars and Mustangs. The only difference between the late and early pigtail is that the late plug is white and the early plug is black. No difference in wiring.

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Used wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...