1971 Mercury Cougar

Used jumper wire for the door ajar switch as found on 1971-73 Mercury XR7's. One end has a spade connector for the ajar switch, the other end is a bullet connector to the main door harness. Fits both driver and passenger side, about 41 inches in length.Replaces Ford part number D1WB-10C865.

Driver side door wiring harness as found on most 1971-73 Cougar XR7. Used on all XR7's unless it had the power window option. Harness for ajar and door stereo speakers, even if it was an AM radio car. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Ford part number D1WB-13A769-BE or D1WY-13A769-E.* Note - Not for cars with power windows.

Passenger side door wiring harness as found on most 1971- mid 72 Cougar XR7. Used on all XR7's unless it had the power window option. Harness for ajar and door stereo speakers, even if it was an AM radio car. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Identified by having a white plug for the ajar wire. Ford part number D1WB-13A769-AE or D1WY-13A769-F.* Note - Not for cars with power windows.* Note - Not for late 1972 or 1973 cars, blue...

Power window door and main harness from a 1971-2 Mercury Cougar or Ford Mustang. This driver side door harness has the power window plug, door ajar plug, and stereo speaker plug. Factory harness, the extra plugs were not used if you had a standard model or AM radio. Tested and inspected and ready to install. Does not include any of the other power window harness segments, i.e. passenger side door, rear windows, or under hood segments. Switches also not included. Does not fit 1973 or later...

Power window door and main harness from a 1971-2 Mercury Cougar. This passenger side door harness has the power window plug, door ajar plug, and stereo speaker plug. Factory harness, the extra plugs were not used if you had a standard model or AM radio. Tested and inspected and ready to install. Does not include any of the other power window harness segments, i.e. driver side door, rear windows, or under hood segments. Switches also not included. Does not fit 1973 or later cars, 1973 was a...

D1WB-13A769-AE Right side door wiring harness as found on 1971-72 Cougars with factory installed stereo. Master part number D1WY-13A769-E. This is a grade "B" good used harness, expect minor splices, damaged rubber boots or other easily repairable minor damage.

Premium grade and quality reproduction floor pan plug. These screw right onto the floor pans prior to the carpet underlay and are much better quality than the originals. The original plugs have rough stampings and are made from galvanized steel. These premium plugs have a smooth cutout and are zinc plated. Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford...

This A/C evaporator drain hose is molded flex hose similar to the original, but it will need to be cut to the proper length. It is correct for 67 - 68 but can be made to work on 69 - 73. Replaces Ford part #: C7ZZ-19858-C or C8TZ-19858-A.

Replacement oil pan plug that is magnetized for collecting ferrous metal in the oil system. Replaces Ford part number C5ZZ-6730-M and D1AZ-6730-A. Fits all Ford engines 1967-73, including 6 cylinder, 289, 302, 351w, 351c, 352, 390, 427, 428, 429, 460.

New oil pan drain plug, Ford engine blue painted, with plastic gasket.  Looks correct, but has a different sized head than factory oil pan bolts. Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200,...

New Chrome oil pan drain plug, with plastic gasket. Has a different sized head than factory oil pan bolts.Correct 1/2" - 20 bolt diameter and thread pattern for factory Mercury Cougar and Ford Mustang V-8 oil pans 1967-73.Replaces Ford part # D1AZ-6730-A / D1AZ-6730-B (bolt) & C2OZ-6734-A (gasket).The Ford Master Parts Catalog lists bolt D1AZ-6730-B as the service replacement for all factory oil pans for the 200, 240, 250, 289, 302, 351, 352, 410, 427, 428, and 429 engines 1965-1973. ...

New oil pan drain plug with zinc coating and plastic gasket. Fits all Mercury Cougar and Ford Mustang V8 oil pans 1967-73.

If these drain plugs are absent mice will be able to find their way into your car. Sold as a pair. Replaces Ford part #: C7ZZ-6511202-A.

This is the gear on the upper side of the gearbox. The cables go over each side of the gear.NOTE: Be sure the gear is in good condition so your cables don't get worn out!

Check your door data plate for code U in the transmission box. Shaft diameter 3 inches. Length 50-13/32 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. Ford part # D1WY-4602-C.*NOTE* Excludes Q code 351CJ engines.

Check your door data plate for code X in the transmission box. Shaft diameter 3 inches. Length 54-1/4 inches, measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length.

Shaft diameter 3 inches, length 53-15/16 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. *TRIVIA* All manually shifted H-code 351-2V engines were 3 speeds, you could not get the 4 speed with that combo. Read about it in Cougars by the Numbers book.

Shaft diameter 3 inches, length 53-13/16 inches measured on U-joint centers. Used and 'as balanced' from the factory. Ask about slip yokes. Shipping is oversized due to length. *TRIVIA* All 71-73 stick shift 351C-4V powered Cougars were equipped with the top loader 4 speed transmission.

This shim, also referenced to as washers, goes in the clutch portion of the drive gearbox to properly adjust the friction. Three shims (plus a hand crank) were originally supplied with sunroof cars.

Front guide that measures 10 5/8" long held in place by four screws. The driver side has no markings but the passenger side is stamped with an R and the inner 2 screw holes are in a different place than the passenger.

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from original 1971 M code and 1972-73 Q code Cougars equipped with the 351C engine. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging...

This 2-1/4 inch dual exhaust system is manufactured right here in the good old USA from an original 1971 429CJ Cougar. This direct replacement system includes: 1 H pipe, 2 intermediate pipes, 2 mufflers, and a right and left tail pipe. The system is constructed from 2-1/4 inch aluminized piping and features blue printed bends with everything being replicated as close as possible to the original. The mufflers in the system have the hanging tabs attached so that they will accept original...

Dual points conversion kit for all Ford V8 distributors. Big block and small block, parts included shown in pictures. Ford part number D0AZ-12A132-B.

There are two of these insulator plates used on the driver side master control switch. Sold individually.

Used fresh air vent duct found behind the driver side dash panel of all 1971-73 Mercury Cougar without air conditioning. Restoration tip - Ford used a ring of foam as a seal between the duct and fresh air vent. Replaces Ford part number D1WY-6501878-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "B" part and will have one defect. This part will have a crack, chip missing, etc. Fits 1971-73 Mercury Cougar and Ford Mustang with factory air conditioning. Replaces Ford part number D1ZZ-18C366-A.

D1ZA-18C433 lower heater duct to floor outlet for 1971-73 Mercury Cougar and Ford Mustang without air conditioning. Used grade "A" part and may have one very minor scuff. Ford number D1ZA-18C433-AD

Used passenger side air conditioning duct for any 1971-73 Mercury Cougar or Ford Mustang with factory or integral A/C. Connects the center manifold to the passenger side elbow or connector.Replaces Ford part number D1ZZ-19B680-A or D1ZA-19C735-AB.

Reproduction driver side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.

Reproduction passenger side concours correct vented dust shield for the 69 - 73 Cougar or Mustang. Painted and ready to bolt on.Side specific.

Clutch Lever Dust Boot for the 289, 302 and 351. Replaces Ford Part #: C6OZ-7513-C.

Reproduction clutch lever dust boot for the Mercury Cougar or Ford Mustang. This unit is used with the 429 in 1971 and in all Cougars and Mustangs in 1972 and 1973 equipped with manual transmissions and the 351 engine.Replaces Ford part #C5AZ-7513-A.

This Lower Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73. Replaces Ford part # C7OZ-3105-A.Just and FYI, in order to install this boot, the entire lower ball joint must be removed from the lower control arm. That means grinding or drilling out the rivets, or removing bolts is so equipped.

This Upper Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73.Replaces Ford part #: C7OZ-3105-B.*Installation tip - The inside diameter of the grommet is just a hair too small to properly fit on the stud. Restoration expert and MCA Judge Marcus Anghel, suggests using a slightly larger round punch to open the hole slightly. If the boot isn't seated low enough, the boot will tear and fail in short order.

Fuel pump drive eccentric for Ford 351C engines 1970-74. Used eccentric from our wrecking yard. Includes inner and outer eccentrics, bolt, and washer. 2-1/2 inches in diameter. Ford part number D0AZ-6287-A.

This elbow is zinc plated for years of reliable service and is for 351, 390, and 428 engines. Replaces Ford Part #: D0AZ-18599-A.

Replaces grommet in chrome oil cap with PCV valve. Inside diameter is 37/64". Replaces Ford part #: C8AZ-6892 or C8AZ-6A892-A.

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

This emblem was used on the driver side of the 1971 - 1972 Cougar hood and on the passenger side of the trunk lid in 1967 - 1968. Also used on various other Mercury products like the Comet, Cyclone, and Marquis prior to 1973. This will not fit on the fender extension of the 1967- 1968 Cougar. Fantastic quality part... In our experience, we have found that you would have to obtain several NOS emblems before you found one with chrome as nice as this. The quality on these new emblems is very...

This used grade A emblem will have good chrome and mounting studs and plexi center. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot...

This used grade B emblem will have good chrome and mounting studs, but the plexi center will be faded. These can be opened up and repainted from the backside. The paint can be obtained from stores that sell modeling supplies. These mount on the lower part of the roof behind the quarter windows. This part of the roof is also known as the 'C' pillar. Ford engineering number on backside is D1WB65517A20-AB. We also offer new barrel nuts for installation. ...

Used Grade "B" center grille emblem for the 71 - 72 Standard Cougar. Will have fading, pitting and the plastic lens area will need to be restored. Ford part number D1WY-8A223-A

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

Good used emblem with no bends, but will be scratched. Will need new adhesive tape as these did not come with studs. For any Cougar, but only came on 1969-70 Standard Models, and all 1971-73 Mercury Cougars. 1971-73 XR7 and Standard Models, as well as convertible.We often get asked about where to place 69-70 XR7 and Cougar adhesive emblems. Based on personal experience and pictures from the original Ford archives the answer would be "Pretty much wherever you think looks best". Often as seen in...

Used driver side (left hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Used passenger side (right hand) XR7 door panel emblem for the Mercury Cougar. The emblem shown is not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold individually.

Used XR7 door panel emblems for the Mercury Cougar. The emblems shown are not faded, most likely the emblem you receive will be faded from black to a bronze color. Keep in mind the cat always walks forward. Sold as a pair.