1971 Mercury Cougar

Good used switch ready to install. Correct switch for the passenger side door and rear seat passenger area. Ford part number C9AZ-14529-D, engineering number usually stamped on the side reads C9AB-14529-A.

Reproduction power window switch, replaces the all of the switches for 1969 and very early 1970. Master switch panel and individual door and rear windows. Replaces C9AZ-14529-D switch.However, for most of 1970 and through 1972, these will not work in the master power window switch panel. That switch is also available, see related products tab.

NOTE!!!! This offshore switch is assembled with plated steel rivet contacts as opposed to brass rivet contacts like original. Whereas the Torino or Mustang do fine with 2 incandescent rear bulbs the Cougars with 6 bulbs put too much load on the switch and they fail. The only way these switches will hold up in a Cougar is if you convert to LED. We are hoping the supplier will take our advice and correct this problem but until such time we cannot warranty this product. Don Rush 9-11-2017 1970-72...

Our turn signal switches are tested and working. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch.Replaces Ford part # D2AZ-13341-C. Replaces Ford...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Tested and working used 2 speed windshield wiper switch for any 1971-73 Mercury Cougar and Ford Mustang. Replaces Ford part number D1ZB-17A553.

Used convertible top switch for any 1971-73 Mercury Cougar Standard Model Convertible - Non-XR7. This is a momentary push switch. Tested and and working used switch.Replaces Ford part number D1WY-15668-A.

Used switch panel with 3 switches for all 1971-73 Mercury XR7  with convertible tops. Inspected and tested switch panel for COURTESY - MAP - TOP. All three switched prove will function and operate. Toggle tips included. Do you have extra, or non working 1971-73 XR7 convertible top switch assemblies? As long as the circuit board part of it isn't damaged we will buy them for $30. Switch assembly must be stamped D1WB-15668-AA on the reverse. *Note - Excludes Non - XR7 model...

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

This little cover glues onto your spoke at 6 o'clock and serves to cover the gap between where your rubber horn switch starts and then stops. NOTE: The 69 steering wheel does not take one of these covers because the bottom of the horn pad actually comes down far enough to cover the rimblow gap spacing.Replaces Ford Part #: D1ZZ-13875-C. Check out this video

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

These new navy blue shirts feature a distressed white graphic with the slogan, "It's Like A Mustang, Only Better!" and "Cougar: Since 1967", wrapped around the image of a first-generation Cougar. This design is a WCCC original, and we think it sums up most Cougar owners' true feelings about their cars. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

UPDATE: These shirts are now the correct size and better quality than the first run!New Team Cougar long sleeve jersey. Our entire design team (that one guy sitting in the back office all by himself) has come up with a new sporty looking long sleeve black tee featuring a Mercury man on the front left chest, "Mercury" script down the right arm, and the Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand. ...

These new XR7 shirts are bold and elegant, just like the cars they represent. On the front left chest is a recreation of the C-pillar badge found on 1967-1968 Cougar XR7's, and on the rear is a nice big crest that mirrors the 1969-1970 XR7 emblems. Screen printed on quality 100% cotton black tees, these shirts are the perfect way to display your allegiance to the classiest muscle car of all time: the Mercury Cougar XR7. Oh, and they make a great gift, too! ...

Brand new ladies athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life. Shirt specs: 6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTapered neck and shouldersSeamless...

Brand new athletic T-shirt from West Coast Classic Cougar! Features distressed university-style block letters and a walking cat logo in gold, on a comfy navy blue heather shirt. A great way to represent your favorite car, favorite coast, or favorite car parts business. Makes an excellent gift for the Cougar fan in your life.Shirt specs:6.0 oz., pre-shrunk 50/50 cotton/polyesterDouble-needle stitched neckline, bottom hem and sleevesQuarter-turnedTaped neck and shouldersSeamless seven-eighths...

New from WCCC! This black T-shirt features subdued grey graphics on front and back, with a small WCCC logo on the front left chest, and a rear view of a 1967-68 Cougar on the back with the taillights lit up in red. We think this is a great looking shirt that all classic Cougar fans will enjoy. Shirts are Port & Company, 4.5-ounce, 100% ring spun cotton, with removable tags. These are softer and more comfortable than some of the previous shirts we've used. Pre-shrunk, but cold wash is...

Tested and working 71 - 72 6000 RPM standard face tachometer with correct brake and oil indicator light windows. Ford part number D1WF-17360-F Shipping and Packaging Tips: Tape something over the face of the tachometer, or put them into a small container to protect the delicate needle. We normally use plastic sandwich containers that protect the face of the tachometer from coming into contact with packing materials or the cardboard box. Please make sure that the tachometers are packed so...

This was an instruction tag for the customer on how the Rim-Blow horn functioned. It would have been hanging from the steering wheel when the car was new. See product images for factory placement example.Replaces Ford Part #: C9ZF-13A875-AA

This 165 page book has been in the works for over a decade now at Marti Auto Works and it is a must have for anyone purchasing, restoring or researching a 1967-1973 Mercury Cougar, Ford Mustang or Shelby. Even if you are a Mopar or Chevrolet guy, if happen to frequent swap meets and salvage yards you need this invaluable little book tucked away in your tool box or car as you maybe walking right past VERY valuable cars and parts and not even know it... In Kevin's words, "Have you been...

Used corner cut from a 1971-73 Mercury Cougar. This would be the driver side where the quarter extension and bumper filler mount. Really it is two pieces spot welded together to the tail panel, quarter panel, and trunk drop off. These may have some pitting or minor rust in the trunk drop off area. 

Used corner cut from a 1971-73 Mercury Cougar. This would be the passenger side where the quarter extension and bumper filler mount. Really it is two pieces spot welded together to the tail panel, quarter panel, and trunk drop off. These may have some pitting or minor rust in the trunk drop off area. 

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. D2ZP-7A040-A version also available, we have a good supply of the updated 1972 version. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not fit full sized Ford Mercury cars that have an FMX,...

Used FMX transmission tail shaft or housing extension as Ford called them in the Master Parts Catalog. Fits all 1969-73 Mercury Cougar and Ford Mustang cars with transmission code X on the door tag. Cast aluminum construction. C9ZP-7A040-A version also available for slightly more money. Exact same part, just got updated for some engineering or manufacturing reason. The overall length of this housing is 12 7/8", which was also used on 1969 Fairlanes and Torinos.  This housing will not...

Internal tail shaft assembly from a FMX transmission. We only disassemble up to what you see in the picture.  *Excludes some FMX transmissions with 351C-4v in 1970. We do not have the larger diameter version available.

Used grade "A" taillight wiring harness for the Mercury Cougar. No cuts or splices, perfect plugs with no visible corrosion.  This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-B before 2/1/71 and D1WY-14405-D from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford part # D2WY-14405-A.*NOTE* Need help diagnosing a Cougar...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13441-AA ...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13440-AA ...

This is how most of our taillight panels are cut off. If you only need a partial panel we can do that too, just give us a ring. Keep in mind we only cut panels like this if both 1/4's are ruined. It is getting very hard to come up with some of these cuts.Click on images to enlarge. ...

This oddball sequential unit was only used from 2/1/1971 to 5/15/1971 and will be of no interest except for to select few. The differentiating factor is the hard plastic connectors. We can supply a reproduction of this unit but it requires that you send your old unit to to us so we can reuse the plugs. Ford part # D1WY-13A366-C. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Used grade "B" taillight wiring harness for the Mercury Cougar. This harness may have one or two professional repairs.This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-B before 2/1/71 and D1WY-14405-D from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford part # D2WY-14405-A.*NOTE* Need help diagnosing a Cougar turn signal...

Used grade "A" taillight wiring harness for the Mercury Cougar. No cuts or splices, perfect plugs with no visible corrosion.  This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar...

Used grade "B" taillight wiring harness for the Mercury Cougar. This unit may have one or two professional repairs.This harness is for the EARLY 1971 (before 5/15/1971). There were 2 harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Used grade "B" taillight wiring harness for the Mercury Cougar. This unit may have one or two professional repairs.This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-A before 2/1/71 and D1WY-14405-C from 2/1/71 - 5/15/71).  Ford Part Number: D2WY-14405-B. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

New temperature sending unit for the 1970 - 1971 Mercury Cougar and Ford Mustang with an actual temperature gauge and a 428, 428CJ (Cobra Jet) or 429CJ (Cobra Jet) engine. Replaces Ford Part #: D0ZZ-10884-A (SW-925)Check out the video below on our new gauge tester: ...

This specially machined screw tensions the friction clutch assembly in the gearbox.

The Big Book is here! This cache of cool Mercury Cougar knowledge features 186 entertaining and informative pages that focus on the 1967-73 Cougar. Don Skinner, former editor at the Cascade Cougar Club, spent 8 years mining valuable data throughout the Cougar community and compiling all of his little gems into "The Big Book." This jewel is chock-full of great tech information, pictures, fun facts, production numbers, rare concept cars and much, much more. Many of the photos and documents...

Here's a new book about the luxury king of classic Cougars, the XR7 G! The book contains many pictures and documents never published before. A great addition to your collection!From the author of The BIG BOOK of Cougar, Don Skinner.

Here's a new book about the king of classic Cougars, the GT-E! This book starts out with the standard '68 Cougar and XR-7 as both models were available with the GT-E option. The reader is then taken through the early stages with the XR-7S and prototypes. Following these pages is the GT-E as we all know it, and then a brief venture into 1969. Lastly are parts lists for the 427 GT-E and the 428 GT-E. This book was written for the casual reader as well as the GT-E enthusiast.The book contains...

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part. Check out this video

195 Degree Thermostat for the 351C, 351M or the 400. Factory spec temp for these engines is 192 degrees. Properly blocks off port that recirculates the water through the engine.

This fail safe thermostat can save you from costly engine damage during an overheat. They feature an exclusive technology that locks the valve open position if overheating occurs. This allows for maximum coolant flow when you need it most.

For use in any 1967-1973 Mercury Cougar except for the 351c in stock configuration. Will work on 351c when you use this Bypass / Restriction plate conversion part.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Reproduction concours correct premium thermostat for the 351C. This is the correct thermostat you would use in conjunction with the new concourse restrictor / by-pass plate on 70 - 73 Cougars and Mustangs equipped with a 351 Cleveland engine. This is a the assembly line style thermostat.  Replaces Ford part number D0AE-8575-B.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.

Fits all* Ford V-8 engines, 1967 - 1973. *- NOTE: This will fit in the 351C, 351M or 400 but will not block off the port to recirculate the water back through the engine.  This can cause the engine to run hotter than desired.