1971 Mercury Cougar

Used 2 screw rear mount sun visor bracket for the Mercury Cougar or Ford Mustang coupe. The MPC lists other part numbers such as D1ZZ-6504132, D2ZZ-6504132, and D3AZ-6504132, which are specific to some colors, but we have yet to seen them in a car. The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, so mention it in the 'comments' section of your order. Ford part # D1AZ-6504132,...

Gray plastic rod with rubber visor tip. Fits most 70's cars built by Ford. Replaces Ford Part #: D3AZ-6504114-B. Customer review: Called WCCC the other day after calling around to a lot of garages and auto parts stores trying to find out the torque specs for my rocker arms on my Cougar. I wanted to check to make sure they where in specs when I was replacing my valve cover gaskets. No one I called could tell me because it wasn't on there computer. At WCCC they said they were not sure but looked...

Visors are fully padded and covered with the correct vinyl or textured tier to match the headliner. Sold as a Pair.

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 3 piece set, which includes: D1WY-8283-A and D1WY-13B116-B. Driver side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 3 piece set, which includes: D1WY-8282-A and D1WY-13B116-A. Passenger side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

Used brake pedal support bracket for the Mercury Cougar or Ford Mustang equipped with manual drum front brakes and an automatic transmission. This unit is not for cars produced after 6/25/1972. Ford part # D1ZZ-6501508-C.

D1ZZ-6501508-D This is the correct hanger for a 1971 Mercury Cougar or Ford Mustang and 1972 cars up until 6-25-1972, with power disc front brakes, and with automatic transmissions. Ford master part number D1ZZ-6501508-D for power disc front brakes.

Used front support bracket for the air conditioning compressor assembly. Starting in 1971, Ford eliminated the idler pulley and used this bracket in it's place. Replaces part # D1AZ-2888-B.

Support bracket for attaching headlight assembly to the radiator core support. Right and left are the same, two needed per car. Fits 1971-73 Mercury Cougar.Ford part number D1WY-13B065-A.

This support bracket mounts to the lowest portion of the quarter window cavity. This bracket is installed before the lower guide bracket. Fits all 1971-73 Mercury Cougar models and 1971-73 Ford Mustang models including fastback or sport roof models. The exploded view of the quarter window parts can be found in the Osborn Body Assembly Manual for 1971-72. One for each quarter window

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.

Sold as a pair. Replaces Ford Part # : D0OZ-8052 Check out our video on Radiator and Fan upgrades below:

Used pair of lower radiator brackets as taken from any 1971-73 Mercury Cougar or Ford Mustang. Additionally these will also fit 1970-71 Ford Torino / Fairlane and 1970-71 Mercury Montego / Cyclone. Should be for all engines. 250 6 cylinder, 302, 351, and 429. Right and left are different, plan on purchasing the insulating rubbers, they may not always be included. Ford part numbers D0OB-8052 or D0OZ-8052-A for passenger side, D0OB-8B381 or D0OZ-8052-B for the driver side. Check out our video on...

This is the Left hand or driver side spring that holds the rear license plate or fuel door in the upright position. Fits all years of Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-B

This is the right hand or passenger side spring that holds the rear license plate or fuel door in the upright position. Fits 1967-68 and 1971-73 Cougar and 1966-71 Torino and Fairlane models except Station wagon and RancheroFord Part #: C7WY-13455-A

Here is our free 7MB download for the 1967 - 1972 Mercury Cougar suspension diagram.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

For any 1971, 1972, 1973 Mercury Cougar. The 1/2" sway bar for Competition Handling was optional on any 1971-73 Cougar, but it was included automatically on all 1971 GT's, 429 Cobra Jets, and with the 1972 & 1973 Q code engine option (351CJ). Concours restorers, should be painted all chassis black with 1 White stripe. This factory used 1/2" rear sway bar, does not include any mounting brackets or end link kits. Replaces Ford part number D1WY-5A772-A.Here's our little film to help you...

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm. 8.0 oz., pre-shrunk 50/50 cotton/polyester1x1 athletic rib with spandexBrass zipper and dark grey trimSelf fabric lined collarSatin labelDouble needle stitching at waistband and cuffsQuarter-turned ...

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on your Mercury Cougar or Ford Mustang. Good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit.Ford part # D1ZZ-19986-A.

Used air conditioning thermostat switch for any 1971-73 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part numbers D1ZA-19618-A or D1ZZ-19618-A.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with power brakes. High quality replacement brake light switch, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: D1ZZ-13480-B.

D0AZ-2B264-A Identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems.

New Old Stock Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1971-73 Mercury Cougar and Ford Mustang without automatic seat back release option. Has a white button for the switch as shown. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1968 - 1973Mercury Cougar and Ford Mustang. Replaces Ford Part #: C8OZ-13713-A.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option.Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

Courtesy light door jamb switch with automatic seat back release option. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A. This is a new reproduction part not Motorcraft.

D1AZ-14018-A Door ajar switch found on 1971-73 Mercury Cougar XR7's and part of the Convenience Group package found optionally on standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light. Switch is the same for both doors. This switch was also used on 1972 Lincoln MK IV, and 1972 Ford Thunderbird.Fits 71 Cougar and XR7Fits 72 Cougar and XR7Fits 73 Cougar and XR7Fits 72 Lincoln MK IVFits 72 Ford Thunderbird ...

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

Unlike the 1968 Cougar headlight switch, the 1967 and 1971-73 version does not have the three vacuum ports connected to it. Don't be fooled . . . Most vendors will sell you a Mustang switch and tell you it is the same. Visually it may look the same but internally it has a circuit breaker designed for a two headlight system, the Cougar has four headlights. If you only use the low beams you would be fine but if you have all four lights on you will soon experience a blackout. If your original...

This is a tested original FoMoCo headlight switch that will work, there is no warranty. Used headlight switch for four headlight bulb systems and without vacuum headlight covers. Comes as shown, for 1967-68 Cougar applications you will need the headlight mounting bracket.Replaces Ford part # D2AB-11654, D3AB-11654, C5AB-11654

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

This used heater fan switch mounts to the rear of the heater control panel. It is a good working switch, wiring pigtail, and plug. Also, because it is original, it will fit right the first time. Save your knob, because this part does not come with one. If you don't have the knob, its OK, I know where you can get a mint set. KNOBS. Replaces part # D1ZZ-18578-A.

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

This is a used intermittent wiper delay switch which is sometimes called the intermittent wiper delay module. The intermittent wiper delay switch can be identified by a grounding wire that is attached to the housing. Sometimes interval or delay is used in place of intermittent for this unit.*NOTE* Must be used in conjunction with an intermittent wiper controller.Replaces part # D1ZB-17A553-BB, D2ZB-17A553-AA, MPC # D1ZZ-17A553-B.

Tested and inspected neutral safety switch for the C-6 transmission installed in 1970 - early1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971.Look for a transmission code of U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: D1ZP-7A247-AA, or D0ZZ-7A247-B, SW 920.

New Old Stock neutral safety switch for the FMX transmission installed in 1969- through early 1972 Mercury Cougar and Ford Mustangs. Found on cars before build date 12/1/1971. These mount in the shifter bucket, see your shop manual for installation adjustment.Look for a transmission code of X on your door data plate. Replaces Ford Part #: C9ZA-7A247 or C9ZZ-7A247-C, SW 903.

This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug that will not be utilized when used on a 69 - 71. Ford part #: D2ZZ-7A247-B, SW 903B Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked...

Quality reproduction for all 1969-73 Mercury Cougar and Ford Mustang with FMX automatic transmissions. This FMX switch is correct for 1972 and 1973 but works fine on 1969, 1970 and 1971. The only difference is that the later models had one extra plug and wire that will not be utilized when used on a 1969-71. All but one plug will be utilized on the 1969-71 applications. This plug and wire is not needed and can either taped off or clipped. Replaces original Ford part numbers C9ZZ-2A247-C,...

Hard to find New Old Recent Stock switch for the driver side power seat on the 71 - 73 Cougar or Mustang. Toggle switch looks accurate, however, you will need to reuse your original plugs. PLUGS NEED TO BE CHANGED FOR SPECIFIC APPLICATION. Some of the Ford part numbers include: D1WB-14B723-AA, D1WB-14B723-Ab, D2WB-14B723-AC, D1ZB-14B723-AA, D1ZZ-14A701-A, D2WY-14A701-A.

Good used switch ready to install. Correct switch for the rear seat area.