Engine & Under Hood

C6AZ-6A664-N Original used hose that connects the original PCV valve to the carburetor spacer plate. All 289-2V, 289-4V, 302-2V, and 302-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. Application for mid year 1966 through 1969 289/302 engines, including Cougar, Mustang, Falcon, Galaxie, Fairlane, Torino, Cyclone, Ranchero, and Comet. *Note - These molded and contoured hoses were...

D1OZ-6A664-B Original used hose that connects the valve cover mounted PCV valve and the carburetor spacer plate on 1971 through 1972 Mercury Cougar and Ford Mustang 351C or Cleveland engines only. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *Note - Excludes all 1969-71 351W or Windsor engines, 1970 351C or Cleveland, and 1973 351C engines. *Note - These molded and contoured hoses were...

Concours correct with ink stamped Ford script. Connects PCV valve to carburetor spacer plate. For all 289-2V, 289-4, 302-2V, and 302-4V engines. Ford part number C6AZ-6A664-N. These were held on with wire clamps, available here. *Note – These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally keep in mind that most anything other than period original intake manifolds, valve covers, and carburetor spacer...

Connects PCV valve to PCV transfer tube on the 390, 427-4V, and 428CJ. Inside diameter on one end is .45" the other end is .58". These should be tough to get on so that they will form a vacuum seal. Originally held on with wire clamps, we have those available here  Replaces Ford Part #: C8AZ-6A664-D. Fits Many 1966, 1967, 1968, 1969, and 1970 Mercury Monterey, Marquis, Ford Galaxie, with FE 390 Big Block Engines. We aren't sure why this hose was reproduced as shown. However it will...

Used smog hose. Connects the smog pump to the check valve. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system. Hose only, no clamps included. Hose is about 30 inches long with a 90 degree bend. Inside diameter is 3/4 inch. Ford part number C6OE-9H548-F.

Used smog hose. Connects the metal "T" connector to the check valve. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system. Hose only, no clamps included. Hose is about 19 inches long with a 90 degree bend. Inside diameter is 3/4 inch. Ford part number C7OE-9H534-A.

Rubber bypass hose for 1967 Mercury Cougar with 289 engine. Additionally for all Ford products including Mustang with 221, 260, and 289 engines from 1962-67. Ink stamped C2OE-8597-A in white ink as shown.

Water By-Pass Hose for 351W engines with Autolite® logo and part number imprinted in white ink. Stamped with C9OE-8597-D. This would be correct for Mustangs and other Ford or Mercury with 302 engines in 1969. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Water By-Pass Hose with Autolite® logo and part number imprinted in white ink. Stamped with C2OE-8597-A. Replaces Ford Part #: C7OZ-8597

These are the best CONCOURSe radiator hoses on the market. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. They have imprints that are very crisp and authentic. Each imprint is CONCOURSe correct. Includes Authentic Logo. c7ze-8260-a and c7ze-82-86-a.

CONCOURS radiator hose set, both upper and lower with C8ZE-8260-E and C8ZE-8266-E marked hoses. Used on both 20" and 24" inch radiators. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video:

New silicone radiator hoses for the 67 - 68 Cougar or Mustang with the 289 or 302 engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Used on both the 20"...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Hoses are also approved by Ford Motor Co.

These are the best CONCOURS radiator hoses on the market. Made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Features special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct including Autolite logo. Hoses are also approved by Ford Motor Co. Replaces Ford Part #: D0ZE-8B273-B &...

These are the best CONCOURS radiator hoses on the market. Ink stamped for all 1972-73 Mercury Cougar and Ford Mustangs with 351C engines. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. Hoses are also approved by Ford Motor Co. Has "MOTORCRAFT" and Ford part number D2OE-8B274-DB ink stamped on the hose. Has OEM style hose clamps stapled onto them like the factory installed hoses.

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct including the Autolite logo. Hoses are also approved by Ford Motor Co. Replaces Ford Part #:...

New silicone radiator hoses for the 69 - 70 Cougar or Mustang with the 390 or 428CJ engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Replaces Ford...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct for the specific application year. Represented by an oval...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct for the specific application year. Represented by an oval...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear, both of which were suppliers to Ford Motor Co in the day. They are approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct for the specific application...

These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have imprints that are very crisp and authentic. Each imprint is CONCOURS correct including the Autolite logo. Hoses are also approved by Ford Motor Co. Replaces Ford Part #:...

Air conditioning belt tensioning pulley with new bearing. This adjustable bracket and pulley was used on all 1970-73 351 engines that came with A/C, as well as 1970 428CJ & 1971 429CJ. This part often has a casting number of D0AA-8A617-C1 but not always. This adjustable idler pulley is identified by having the large bearing pulley. Same as the C8AZ-8678-A adjustable idler pulley only with a small bearing pulley. We also offer a bearing replacement service to rebuild your adjustable idler...

Air conditioning belt tension pulley. For Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C7AZ-8678-B. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

Used A/C belt tensioning pulley with new bearing. Ford standardized some of the brackets starting in 1968. This adjustable bracket and pulley was used on all 1968-69 390 / 428CJ engines and 1968 289 and 302 engines after 3/1/1968. Additionally it was on 1969 351W engines as well. This adjustable tensioner pulley is identified by having the small bearing pulley. Same as the DOAZ-8678-C adjustable idler pulley only with a big bearing pulley. *Note* All new bearings will have a slight bit of play...

Service replacement A/C belt tensioning pulley with new installed bearing. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc.*Note* All new bearings will have a slight bit of play in them. This is by design, by...

New sealed bearing for installing on your 1968-73 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing also came in all of the "service replacement" idler pulley assemblies and is physically larger than the idler bearing for the 1968-69 only idler pulley (68-69 bearing sku: 10827). The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 9/16". On the smaller bearing pulley, this measurement is 1 3/8". Both versions of this...

New sealed bearing for installing on your 1968-69 Mercury Cougar or Ford Mustang idler / tensioner pulley. This bearing is physically smaller than the bearing used on the 1968-73 idler pulley (1968-73 bearing sku: 10462). The 1968-73 idler pulley assembly came as a "service replacement" on 1968-69 cars. The center portion of the pulley, where this bearing would press into, has an inside diameter measurement of 1 3/8". On the larger bearing pulley, this measurement is 1 9/16". Both versions of...

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which were used starting in...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 351W or 351C engines. Sometimes has Ford number D0AA-8A617-A stamped on the bracket, not always.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which were used starting in 1968, now have an ever so slight amount of play....

Used bracket and pulley assembly for 1967 Cougar or Mustang with 390 engines. All pulleys with bearings are sold in working used condition. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got the parts you need! Ford part # C7SZ-8678-B. ...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 428CJ engine. This is also a service replacement part for the C8AZ-8678-B fixed idler pulley. The only difference between them is that this part has the larger bearing.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which...

These replacement "Yellowtop" ignition coils are copies of the original. Nice reproduction cosmetically and functionally. This is a very prominent piece and a must have when trying to detail your engine compartment properly. Replaces Ford part # B6A-12029-B.   Note, no decals are included. Check the website in related items.

C8OZ-3C511-C Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 Cougar or Mustang with 289 or 302 engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

C9OZ-3C511-A Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1969 Cougar or Mustang with any 302 / 351 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

3C511-351-71 Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1971-72 Cougar or Mustang with any 351 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

3C511-351-73 Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1973 Cougar or Mustang with any 351 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

Replaces Ford Part # : C8OZ-3C511-B

C7AZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1967 Cougar or Mustang with any V8 engine. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

C6OE-9425-A Cast iron intake manifold used on all 1967 C code 289-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4AZ-9424-H. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

C8AE-9425-B Cast iron intake manifold used on all 1968 C code 289-2V, and F code 302-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of C8AE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4AZ-9424-J. The 1966-67 289-2V intake is also a good alternate, see related items for that one.*Installation Tip - A 1 inch aluminum spacer...

C6OE-9425-B Cast iron intake manifold used on all 1967 A code 289-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C6OE-9425-B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-G. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

Very rare over the counter, Group II dress up accessory item for any 289 / 302 small block engine. In excellent used condition with no cracks, stripped threads or corrosion damage. The nicest you will ever find. This over the counter Intake was marketed by Shelby American in the Cougar catalog titled "How To Sharpen Your Cat's Claws". Shelby casting number S2MS-9424-A. This intake is basically the same one you so often see with COBRA lettering on it. New to our inventory as of 12-15-2017, the...

C8ZE-9425-A Cast iron intake manifold used on all 1968 J code 302-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C8ZE-9425-A. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C4OZ-9424-H. *Installation Tip - A 1 inch 4 barrel aluminum spacer plate with PCV provision is needed for proper air cleaner clearance.

D0AE-9425-M Cast iron intake manifold used on all 1970 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-M. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D1AE-9425-DA Cast iron intake manifold used on all 1971-72 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D1AE-9425-DA. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D1AZ-9424-D. *Installation Tip - A 1 inch aluminum spacer plate with PCV provision is needed for proper air cleaner clearance. *Note - 351...

D3AE-9425-CA Cast iron intake manifold used on all 1973 H code 351-2V engines in a Mercury Cougar or Ford Mustang. Stock 2 barrel intake manifold. Take off manifold with correct casting number of D3AE-9425-CA. Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D3AZ-9424-C. *Installation Tip - A spacer plate with EGR provision is needed for proper installation. *Note - 351 Cleveland engines only. ...

D0AE-9425-E, -H, or -L Cast iron intake manifold used on all 1970-71 M code 351-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of D0AE-9425-E, -H, or -L . Intake shipped bare, less choke stove, carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number D0AZ-9424-C. *Note - 351 Cleveland engines only.