Engine & Under Hood

D2AE-6312-A Application is for both H and Q code 351 engines without air conditioning and without power steering. Single sheave pulley, 6-3/8 inches in diameter and 4-1/8 inches long. Ford Master Part number D2AZ-6A312-A.

Ford casting number C4ME-6A301-A. Single sheave outer pulley for use with power steering as the only option. This pulley is listed in the 1967 engine assembly manual. Listing is for 'Standard Alternator Drive with Power Steering'. Standard alternator would be a single pulley on a 42 amp rated alternator.

D0OE-6312-C For both Cleveland and Windsor 351 engines. This is also the "with air conditioning" pulley, but with power steering option. Triple sheave 8.00", 7-55/64", 6-9/16" diameters. A four bolt hole crank shaft pulley for use with 1970 and upward crank dampeners. Ford Master Part number D0OZ-6A312-B. This is a Service Replacement pulley for D0AE-6312-C. *Excludes 1972 Q code 351 Cobra Jet engines. This means all 1972 351C-4V engines.

D1ZE-6312-C Application - Q code 351 Cobra Jets with air conditioning and power steering. Triple sheave pulley, 6-11/16" and 7-9/16" diameters. Ford Master Part number D1ZZ-6A312-A. *Note - References also list casting number D1ZE-6312-CA as being the same.

Ford part number C8AZ-6A312-A. Application 390-2V, 390-4V engines, and 428 Cobra Jet with air conditioning. Power steering optional, with dual alternator belts. Ford casting number C8AE-6312-A. Triple sheave 68 crank pulley.

D0ZE-6312-B Application is 1970 Boss 302 Eliminator with or without power steering. Triple sheave pulley 5-15/16" and dual outer 6-11/16" diameter. Ford Master Part number D0ZZ-6A312-A. Also a four bolt mount to the crankshaft balancer. The reason for a triple sheave pulley on Boss 302 engines is the inclusion of the Thermactor Smog system from the factory. Smog pumps were placed so that they worked off of the outermost pulley groove on a 3 sheave crankshaft pulley. If with power steering the...

Application, 1969 - 1970 390IP / 428CJ & 428SCJ engines without air conditioning. Casting number 80B. 5-1/2" diameter and 7/16" sheave width.

Application, 1969 Boss 302 Eliminators and Ford Mustang. Ford Part #:  C9OZ-3A733-C Casting #: 90B. 6-3/8" diameter and 5/16" sheave width.

1968 390-4V all with factory manual transmissions and factory air conditioning. Pulley diameter 5.89" inches. Ford part number casting # C8AE-9B480-B. Mounting bolts sold separate.

This is a 3 bolt Thermactor smog pump pulley with a diameter of 5.49" inches for the Mercury Cougar GT-E with the 427-4V W code engine. C8OE-9C480-A marked on pulley.Ford part # C8OZ-9B447-B.

C9OE-9C480-A 1969 and 1970 428 Cobra Jet (R and Q code engines) smog pump pulley with air conditioning, manual and automatic transmissions. 3 bolt smog pump pulley with a diameter of 5.10" inches. Ford part number C9OZ-9B447-A.

1969 Boss 302 Eliminator (G code engine). 3 Bolt smog pump pulley with a diameter of 5.68" inches. Ford part number C8AZ-9B447-E.

1970 Boss 302 Eliminator (G code engine). 3 Bolt smog pump pulley. Ford part number D0ZZ-9B447-A.

C5AZ-8509-J For use originally on 1967 289 engines without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single belt pulley 6.10 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.*This is one of the few water pump pulleys that did not have an imprinted casting number. Originally this pulley had an ink stamp. We will most likely be...

Water pump pulley 1 sheave, about 6.11 inches. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches. Application include 1967 Cougar with 289. 1969 Cougar and Mustang with 390-4V. Also various Mustangs 1965-67, all with 289.Replaces Ford casting number C5OE-8509-A.

Single sheave pulley 6-61/64 inches in diameter.Applications:1970 Boss 302 Eliminators without power steering1970 351 engines without power steering1971 - 1973 351 engines without power steering and without A/C.Ford casting number C9OE-8509-E. Ford part number C9OZ-8905-B *Note - this is a very shallow pulley, it is meant to run in the second belt position from the engine. ...

C6OZ-8509-A For any S code 390 engine without power accessories. No air conditioning, no power steering, and standard 1 sheave alternators. Single sheave pulley, 6-3/16 inches in diameter. When measured from the front of the water pump hub (or inside of the pulley) to the center line of the belt sheave the measurement is 2 inches.Replaces Ford part number C60E-8509-C.

C6AZ-8509-C 390 engines with air conditioning. Power steering and or thermactor emissions allowed. 2 sheaves with a diameter of about 5-5/16 inches. *Notes say after 1-9-1967 engine build date. Ford casting number C6AE-8509-F.

C6AZ-8509-D Strictly California 390 Cougars without air conditioning. With or without power steering. 3 sheave pulley with diameters of both 5-11/16 inches and 6-1/8 inches. Ford casting number C6AE-8509-J.

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

Double sheave pulley, 6-3/8 inches and 5-11/16 inches in diameter pulleys.Application:429CJ with air conditioning and/or power steering. Ford casting number D0OE-8509-L. Ford part number D0OZ-8509-L

Single sheave pulley, 6-1/2 inches in diameter.Application:429CJ without air conditioning and without power steering. Ford casting number D0SE-8509-A. Ford part number D0SZ-8509-A

Used FoMoCo 20 inch small block radiator. This is for a 1967 Mercury Cougar or Ford Mustang with 289-2V, or 289-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 7EC or 3rd week of May 1967. Late production date. Ford part number C7ZE-8005-S1 ...

Used FoMoCo 20 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 8FD or 4th week of June 1968. Very late production date.Replaces Ford part number C8ZE-8005-H1 ...

Used 'CORE" grade radiator, marked C9ZE-D or D1, .. etc. 20 inch used radiator from 1969 Mercury Cougar with Boss 302 or 351W or 1969 Ford Mustang with 302 or 351W or engines. This radiator will have the lower tank for transmission lines. Core grade, likely it has been recored at some point in the last 45 plus years. Limited to stock on hand.Restoring or re-coring OEM radiators is expensive and more for the concours crowd. New or reproduction radiators makes much more economical sense.Ford...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and C-6 (automatic code U) transmission. This supplier with the Ford number stamped on the side strap is typically from Dearborn assembled cars. Used core radiator for recoring and restoration. This listing currently has an older replacement 4 tube core. The lower tank has minor damage to the area of the pet cock as shown. Typical Dearborn installed assembly line radiator.Replaces...

Used FoMoCo 22 inch big block radiator marked C7ZE. This is for a 1967 Mercury Cougar or Ford Mustang with 390-4V and manual transmission. Used core radiator for recoring and restoration. This listing currently has a lower tank with minor damage to the area of the hose outlet as shown. Typical Dearborn installed assembly line radiator.Replaces Ford part number C7ZE-8005

Used Western Modine (W/Mo) 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V or 302-4V engines and (automatic code W) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. This is the typical radiator installed at the San Jose, California assembly plant. W/Mo embossed on the top of the tank with a date. Dated 67-10 or October...

Used WMo or Western Modine 24 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and 3 or 4 speed manual transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Factory installed manual transmission radiators did not come with the fittings in the bottom tank for transmission cooling.Replaces Ford part number C8ZE-8005

Used 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. Replaces Ford part number C8ZE-8005

Used WMo or Western Modine 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Dated 67 12. Replaces Ford part number C8ZE-8005

Used FoMoCo radiator marked C8ZE-L1 and dated 8KB, which we believe is 2nd week of October 1968. This is for an early built 1969 Mercury Cougar or Ford Mustang with 390-4V or 428CJ and 4 speed transmissions. Good used radiator for recoring and restoration.Replaces Ford part number C8ZE-8005-L or C8ZZ-8005-C.

Correct core radiator for any 1970 Mercury Cougar or Ford Mustang with the G code Boss 302 engine. Has correct stamped Ford part number on the side strap, and lower tank without fittings for cooling lines. Core grade, will likely need recoring.Replaces Ford part number D0ZE-8005-E / E1

1969 Boss 302 radiator marked C9ZE-AG1 and dated 9EA, we decipher the date as May 1969, first week. The core of this radiator is junk, and will be removed. The upper and lower tanks and side brackets are all good. Fits any 1969 Boss 302 Mercury Cougar Eliminator and 1969 Boss 302 Mustang, it is dated for a May/June 1969 car. *Note - Please call for shipping on this item as it will be shipping from Canada.

1970 Boss 302 radiator marked D0ZE-E1 and dated 9JD, we decipher the date as Sept 1969, 4th week. It has a 3 core construction as shown, with a rebuild tag. The upper and lower tanks and side brackets are all good. Fits any 1970 Boss 302 Mercury Cougar Eliminator and 1970 Boss 302 Mustang, it is dated for a October - November built car. Nice used assembly line, core radiator with original tanks. *Note - Does not have fittings for automatic transmission lines. All Boss 302 cars had 4 speed...

Found on standard cooling and non-air conditioned Mercury Cougar and Ford Mustang 1969 - 1970 all engines. One per car, one on the drivers side of the radiator. *Note - This is a shorter side shield than is found on the 1967 and 1968 Cougar.*Note - Block off plate not needed with the 24 inch radiators.

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

Made in the U.S.A. by Gates or Goodyear, both suppliers to Ford Motor Co. Upper and Lower Hose that are CONCOURS correct with the correct part numbers stamped on to the hoses as well as the Autolite logo. Replaces Ford Part #: C9ZE-8B274-C & D0ZE-8B273-B.

Original used plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang with 26 inch radiators. Also called a radiator air deflector. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and Mercury cars. Comes with 4 original spring clips for mounting. Clips are not sold separately. Plastic portion is about 24 inches long.  Replaces Ford part number D0OB-8B170-B.

Concours appearance with black case and authentic Autolite markings. Disappointing functionality, often will fail in less than a year. We recommend buying the genuine Motorcraft version instead, or even one of the generic versions we also sell. *NOTE* There are dozens of styles which were produced by several manufacturers. This unit represent the most common type and is marked C7AF-11450-A1 & "AUTOLITE". When you see this icon on a product, it means it's a sub-par item that we don't recommend,...

D2AZ-14A163-K Black plastic ring that barely fits over the PCV hose. Ring end locks into the D1AZ-6788-A hose bracket. Fits all 1972-73 351 engines, both 2V and 4V engines. This retaining ring came from Ford's electrical section.

Reproduction hold down clamp rivet for the 67 - 73 Cougar or Mustang. This rivet holds the clip / clamp onto the distributor. Sold individually, 2 per car.

New temperature sending unit for the 1970 - 1973 Mercury Cougar and Ford Mustang with an actual temperature gauge. Fits 351C and 351W engines. Temp Sender Switch Temp Rating : 22.7-25.5 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPTF Replaces Ford Part #: D0WY-10884-A (SW-924)Check out the video below on our new gauge tester: ...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1969 Mercury Cougar and Ford Mustang with 351W-2V, 351W-2V engines. Ford number C9WY-10884-A.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits 1970 351W-2V, 428CJ, and 429CJ engines. 258° stamped, for Mercury Cougar 1970-73, and Ford Mustang 1970-73.  Ford number D0ZZ-10884-A. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry.Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...