Engine & Under Hood

Reproduction plastic upper radiator seal for 1971-73 Mercury Cougar and Ford Mustang. Also called a radiator air deflector.  There are 2 versions of this deflector for different depth radiators. This is the larger version (smaller version is not reproduced) and can be cut down to work on cars with narrower radiators.  Some cars used clips to hold these on, but most used staples. Also fits 1970-71 Torino, Ranchero, Cyclone and Montego. As well as 1970-72 full sized Ford and...

D0WY-9A091-B Rear evaporative vapor separator, mounts in the drivers side trunk well. *Note - This is only a small part of the 9B004 assembly.

Air conditioning bearing replacement service. Send your flat bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new flat bearing. Either large or small flat bearings, same price.  Dust caps hand fitted, for seamless installation. No extra tool marks, other than the factory peening. Check photos.Ford casting #'s D0AA-8A617-B, D0AZ-8678-D, C8AZ-8678-B, C8AZ-8678-C, C8AZ-8678-A, D8OH-19W653-A, D0AZ-8678-D.*Note* All new bearings will...

Air conditioning bearing replacement service. Send your wide bearing style, fixed or adjustable A/C pulley and we will exchange it or rebuild your exact pulley with a new wide bearing. Price includes new bearing (long or short shaft) and labor, shipping extra.  * Note * There are several pulleys that we are unable to press apart. Please check photos for examples of the known pulleys that we can assemble, but not disassemble. *NOTE* Excludes certain 1968 pulleys with stamped...

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

This is a good quality non-concours starter solenoid. Inexpensive replacement if you are not worried about being 100% correct. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo. Replaces Ford part # B6AZ-11450-A, C7AZ-11450-A & D2AF-11450-A.

Original retainer that clips onto the breather element nipple sticking through the air cleaner base and holds the elbow for the hose going to the PCV valve.  Ford calls this part the Crankcase Emissions Filter Retainer.The Master Parts Catalog says this part is only for 1971 and newer cars, but this part has been found on low mile 1970 cars as well. Ford part # D1AZ-9E628-A.

Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)

Used driver side smog hose. Connects the cylinder head smog tube check valve to the distribution "T" connector. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system. Hose only, no clamps included. Ford part number C7OE-9C433-A.

Used passenger side smog hose. Connects the cylinder head smog tube check valve to the distribution "T" connector. 1967 Mercury Cougar and 1967 Ford Mustang with C and A code 289 engines, and typical California Thermactor smog system.  Ford part number C6AE-9B459-A.

Thermactor smog hose installation clamps. Fits all Ford and Mercury 1968 S code 390-4V or W code 427-4V engines sold in the US. Additionally fits 1968-70 428 Cobra Jet and Super Cobra Jet engines. Set of clamps, several bolts and spacer as shown. Include bolts for pump pulley, top bolt on pump for adjusting bracket, and pivot bolt and spacer for pump.

Reproduction hardware kit for installing the smog pump on cars with 390 / 427 / 428CJ engines from 1968-70. Including Cougar, Mustang, Torino, Ranchero, Cyclone, etc. Includes spacer, pivot bolt and washer, adjusting bracket bolts.

Complete original system as taken from a small block 289 from California. Comes with all items shown and you can choose from the large pulley as found on AC cars or the smaller pulley found on non AC cars. These systems are getting rather elusive to find with pliable hoses, correct Wittek clamps and correct fasteners. For years only those with big block cars cared to obtain original smog systems. That has changed... Even if you do not install it, if your car originally had it it will...

Set of thermactor smog tubes on any 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original 390 or 428CJ cylinder heads drilled for air injection smog system from factory. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the ferrules / nuts and other hardware.

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Nice original snorkel that is correct for 2V and 4V 289 motors both 49 state and California Cougars. Due to the age of these parts, the internal thermal mechanism can be presumed to not work. Ford part number C7ZF-9A626-A.

This air cleaner is the late style without the vacuum actuated valve. Mid year it was changed to a thermal activated valve. After 4/2/1968. 289-2V , 302-2V, and 302-4V engines after 4/2/1968. Ford part number C8AZ-9A626-D. NOS new old stock. ...

This air cleaner is the late style without the vacuum actuated valve. Mid year it was changed to a thermal activated valve. After 4/2/1968. 289-2V , 302-2V, and 302-4V engines after 4/2/1968. Ford part number C8AZ-9A626-D. Click on images to enlarge. ...

This air cleaner is the early style with a vacuum actuated valve. 289-2V , 302-2V, and 302-4V engines prior to 4/2/1968. Ford part number C8AZ-9A626-A.

IMCO emissions air cleaner snorkel for a 1972 Cougar with 351-2V engines only. Non-California, 49 states only. (California required IMCO with NOx, see D2ZZ-9A626-B). Ford part number D20Z-9A626-C.

Application is for all 1971 Cougars with 351 engines, both 2V and 4V engines. Additionally it includes 1972 351-4V without NOx. Our research shows that NOx was a California emissions requirement. Ford part number D10Z-9A626-B. *Note - 1972 49 state 351-4V air cleaner snorkel.

California emissions 351-4V air cleaner snorkel. DSO 52 and DSO 53 Cougars with Q-code 351-4V engines.

Application is for all 1970 351 Cleveland engines, both 2 barrel and 4 barrel. This air cleaner snorkel is different from past years in that the opening is necked down and has a flared flange. It also has a small opening on the bottom for a metal "S" tube. Ford part number D0OZ-9A626-D. Click on images to enlarge. ...

Applications all 1969 351 engines, both 351-2V and 351-4V, and 1970 351W-2V engines after 2/2/1970. That is correct, after Feb 1970 the H-code Windsor engined 351's used a 1969 style air cleaner snorkel.The C9OZ-9A626-B snorkel looks the same, but is a bit longer than the 1968 C8AZ-D snorkel. Probably due to the taller deck height of the 351 over the 302 engine, and or the heat shield design. Please note: Wax stat is not tested, nor can we test them, sold as- is. Click on images to enlarge. ...

This snorkel was found on the 1968 Mercury Cougar and XR7-G models with the 390 or 428 engine and the tall pent roof finned aluminum valve covers. The HERTZ model with the 390 engine used a chrome "Powered By Ford" chrome valve cover and did not need the extra length in the extension. NOS XR7-G Air Cleaner Snorkel for the 1968 Mercury Cougar Equipped with the 390 or 428 Engine and cast aluminum running cat valve covers. Ford part # C8WY-9A626-B. ...

Quality recreation made from original parts. Decent reproduction, slightly different than the original Ford version. The noticeable difference is the lack of square notch in the slop joint. Ford part of C8OZ-9A626-C. This snorkel comes to you in primer.

For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.

Application would be for only 1971 Cougars with the 429CJ option, either ram air or non-ram air. Original Ford part number was D0GY-9A626-A, this unit is from a Ford Truck, part #is from a D3TZ-9A626-G. This is a low cost alternative to a very rare part. Click on images to enlarge. ...

Application would only be for 1969 Boss 302 Eliminators and Boss2 Mustangs.Ford part number C9ZZ-9A626-C.

Although these are considered reproductions, they are actually put together from multiple parts of original excellent condition used snorkels. And, since there are multiple colors of Ford Blue, the supplier is leaving them as unpainted.Application would only be for 1970 Boss 302 Eliminators and Boss2 Mustangs. Ford part number D0ZZ-9A626-B.

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Air cleaner intake assembly or snorkel specific to the one year only 390-2V premium fuel engine, (X code engine). This version has the thermally operated trap door. There was an early version that used vacuum to open the trap door to the heat stove. Ford part number C8WY-9A626-A. *Note - This snorkel has a different spacing on the mounting ears, it will not mount to a 390GT air cleaner base.

Air cleaner intake assembly or snorkel specific to the one year only 390-2V premium fuel engine, (X code engine). This version has the vacuum operated trap door. There was an more common thermal version that used temperature to open the trap door to the heat stove. In most cases the vacuum valve will not be working. Most people are probably better off with the thermal version. We do not know the change over date. Ford part number C8WY-9A626-A. *Note - This snorkel has a different spacing...

Aluminum spacer used on 289/302/351 engines for mounting the alternator. Length is 1-5/8 inches long, mounts between the alternator and the cylinder head.

Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.

Aluminum spacer for mounting the alternator on 1971 Mercury Cougar and Ford Mustang with 429 Cobra Jet engines. Also fits 1970-71 Cyclone and Torino with 429CJ engines. Spacer measures approximately 1-1/16 inches long. Fits between the cylinder head and alternator housing.

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. New manufactured.

B8AZ-6359-A Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. Used spacer, will show a little wear from the outside seal. 

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Reproduction 384542-S2 Power steering pump adjusting spacer for use without air conditioning. For all 1970 and later Mercury Cougar or Ford Mustang with 302 or 351W engines. Spacer dimensions: 7/16" I.D. and 3/4" thick.*Note - 351C engines use a 1/2 inch spacer.

Replaces Ford Part # C7SZ-3D600-A. Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 9/16" thick.

Correct Autolite 24 spark plugs for all 1970-73 351 Cleveland engines. This is what Ford installed originally from the factory. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

Correct Autolite 45 spark plugs for all 1967-73 289/302/351W/390/428CJ engines. This is what Ford installed originally from the factory. BF32 crosses over to this spark plug. Typically these should have a electrode gap of 0.035", with either stock points or Pertronix ignition systems. Sold individually.

Keeps spark plug wires neat and orderly. Mounts on valve covers. Replaces Ford Part #: B8Q-12297-A.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Made of heat resistant black nylon. Keeps spark plug wires neat and orderly.