1969 Ford Mustang

Located on either the left or right hand shock tower. On rare occasion we also have seen these above the washer bottle on the 69-70 models. Replaces Ford Part #: C7AE-6C029-A.

Here's a good replacement for those old worn out aluminum "stereo" decal inserts for your 69 - 70 door speaker grills. Keep in mind that these are just simple decal stickers and are not made from aluminum as the originals were. We do offer used aluminum decals here.SOLD INDIVIDUALLY. ...

Replaces Ford part #C8AZ-6223362-A. Sold in pairs, four required per car, used on most Ford products. We often get calls like "How do I remove my front window cranks?" Unlike the rear cranks that are held on by an Allen set screw, the fronts have a Phillips screw under this decal. If you are careful, often you can reuse your original and glue it back in place.

Reproduction Decal Set / Under Hood Paint OK for the 1969 - 1971 Mercury Cougar or 1971 Ford Mustang 

New Old Stock 'DEFOG' knob. Attaches to hand down defog switch on 1969-70 Mercury Cougar and Ford Mustang with rear defogger option. *Note - Excludes 1970 Mercury Cougar XR7. Those cars had the defog switch in the courtesy light panel. Replaces Ford part number C9WY-18519-A.

Used switch for the rear defog or defogger fan on any 1969 Mercury Cougar, 1969 Standard Cougar, and 1969-70 Mustang coupe or hardtop. Original switch with attached wiring harness. Tested and working two speed switch. Comes as shown with chrome knob marked "DEFOG". Some examples may have minor pits in the chrome knob. Wiring marked C9WA-18C498-A. Excludes all convertible models and Mustang fast backs.Replaces Ford part number C9ZZ-18578-A.*Note - is not technically correct for 1970 Mercury...

Grade A used deluxe shifter handle in black. Nice used condition may have a hairline crack in the plastic on the bottom. No release button or set screw included. See related items for Grade B  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Grade B used deluxe shifter handle various colors. Please specify color in the notes, limited to stock on hand. Fair used condition will have at least one crack in the plastic. May also have slightly pitted chrome. No release button or set screw included. See related items for Grade A  Ford part number C8OZ-7213 The 67 version was actually a little different. Check out our video on rebuilding your shifter below: ...

Reproduction seal for the lid of the brake fluid reservoir for a power disc brake equipped Mercury Cougar or Ford Mustang.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang 1969 Ford Mustang 1970 Ford Mustang 1971 Ford Mustang 1972 Ford Mustang 1973 Ford Mustang ...

Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet.  Replaces Ford part # C9AZ-2167-B.

Fine thread lock nut used in various places on old Fords, including the differential housing, 1967 disc brake assemblies, and more. Replaces Ford part # 34445-S

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new 4 pinion Trac-Loc unit, new Motive ring and pinion gears, new Timkin bearings, new crush sleeve, new bolts, and new seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. There are various ring and pinion (gear) ratios and axle splines available, if you are unsure of what you need it is best to call (503) 463-1130 for your order. This is a drop ship item. *Note - New...

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...

Also called a pumpkin, 2.75:1 open ratio. Check your door tag under "Axle". 1968 code 1 1969-73 code 2

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - Used Also called a pumpkin, 3.00:1 open ratio. These 3rd members will have the fill plug. Check your door tag under "Axle".

D0OZ-4204-9A300 1968-1973 9 Inch Third Member - UsedAlso called a pumpkin, 3.25:1 open ratio. These 3rd members will have the fill plug and 28 splined axles.Check your door tag under "Axle".

Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....

Limited slip 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and new a seal. Rebuilt using the standard 9 inch case, with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it works for any other Mercurys or Fords with a 9 inch...

Limited slip 9 inch Ford third member rebuilt with all new or reconditioned parts. Rebuilt 4 pinion Trac-Loc unit, with new clutches, steels, Richmond ring and pinion gears, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using standard 9 inch cases with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit was used in Cougars and Mustangs, but also any other Fords...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New 4 pinion Trac-Loc unit, Richmond ring and pinion gears, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a nodular 9 inch case with oil fill plug. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but it can also be used for any other Ford or...

Limited slip 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967-1973 standard 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used on any other Ford or Mercury with a 9 inch drop out center section. Because of all the various ring and pinion...

Limited slip nodular 9 inch Ford third member rebuilt with all new parts. New Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, selective size sleeve, bolts, and seal. Rebuilt using a 1967-1973 nodular 9 inch case with oil fill plug. For 28 or 31 splined axles. This unit is for 1967-73 Cougars and Mustangs, but can be used in any other Ford or Mercury with a 9 inch drop out center section. Because of all the...

Since we always claim to have parts nobody else does... This welds to the bottom side of the car just above the differential. When the rear suspension bottoms out, this is the plate the rubber snubber / bumper (mounted on the front on top of the dif.) makes contact with.

Fits both 8 inch and 9 inch rear ends. Phosphate and oil coated with thread sealer. These are one time only nuts. They should not be reused per Ford. Replaces Ford part #: 371518-S

Original dipstick or in Ford speak "Indicator - Oil Level" for C4 automatic transmissions. Application for 1967-68 Mercury Cougar 1966-70 Ford Mustang with 289/302 engines and C4 automatic transmissions, code "W" on your door data plate.Ford part # C6OZ-7A020-B.

Reproduction transmission dipstick tube for 67 - 70 Cougars or Mustangs equipped with the C4 automatic transmission.Replaces Ford Part number C6AZ-7A020-B

Original dipstick or in Ford speak "Indicator - Oil Level" for FMX automatic transmissions. Application for 1969 - 1972 Mercury Cougar and Ford Mustang with 351 and FMX automatic transmissions, code "X" on your door data plate. Sometime during 1972 Ford changed to C9AP-7A020-C. Same dip stick, but with a longer handle.Ford master part number C9OZ-7A020-A, Ford casting # C9OP-7A020-A.

This kit is a must when redoing the disc brakes on a 1968-73 Cougar. Includes new brakets (caliper stabilizers), bolts, pins, and clips and rubber dust seals. Kit includes the pair.

Reproduction disc brake master cylinder cap for the Mercury Cougar or Ford Mustang. This unit has the correct stampings, rubber inner gasket, and is considered show quality. This cap will only fit master cylinder part # 15298.Replaces Ford part # C7AZ-2162.Fits: 1967 Mercury Cougar1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury Cougar 1967 Ford Mustang / Torino1968 Ford Mustang / Torino 1969 Ford Mustang / Torino 1970 Ford...

Reproduction adjustable disc brake push rod set for the Mercury Cougar or Ford Mustang. When you convert to manual disc brakes, this kit eliminates excess pedal travel and insures quicker braking response. NOT for power disc brakes. For Manual disc brake cars ONLY.

Excellent quality replacements. Includes hub, studs, and bearing races. Single piece design. Rotors Are Precision Machined For Smooth Brake Operation.; Qc100 Venting Matches The O.E. Cooling Vanes To Manage Brake Temperature, Prevent Noise & Limit Vibration.  .81" thickness of Rotor brake surface. 

Used core distributor for 1969 Mercury Cougar and Ford Mustang with H code 351-2V and aNY transmission. Core distributors will have correct stamping of C9OF-M. Original Ford part number C9OF-12127-M.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with M code 351-4V and automatic transmission. Core distributors will have correct stamping of C9OF-T. Original Ford part number C9OF-12127-T.

Used core distributor for 1969 Mercury Cougar and Ford Mustang with S code 390-4V and automatic transmission. Core distributors will have correct stamping of C7AF-AC. Original Ford part number C7AF-12127-AC. Current unit has a date of 9B10, or February 10, 1969. Stamped C7AF-12127-AC.

Used Autolite Distributor for 1968 390-4V and 1968-69 428CJ for the Mercury Cougar, Cyclone or Ford Mustang, Torino.  Ford part number  C8OF-12127-D.  

Reproduction dual port vacuum advance for most all 1968-70 Ford V-8 engines. Very close replica of the factory installed vacuum advance. This version has two pressed in brass fittings for vacuum hoses. This working vacuum advance will need to have your threaded plug installed in the port end. OEM Ford units had gold colored bands instead of this silver band as shown. This unit very closely matches the 1970 vacuum advance, the earlier vacuum advances had one of the vacuum fittings that screwed...

Ignitor 1 by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. There is also an upgraded Ignitor II available. -50F To 300F Working Temperature Range, 0-15,000 Rpm Range, This Easy To Install And Maintenance Free Electronic Ignition System Features Solid-State Electronics And Rotating Cobalt...

Ignitor II by Pertronix, effectively replaces your points and condenser from your Distributor. Works in all Ford Autolite distributors found in 1967-73 Mercury Cougar and V8 Mustangs with single point distributors. This is also called an electronic ignition conversion. Adaptive Dwell Control -  Dwell increases with RPM to provide an average of 4 times the available energy between 3000 and 5000 RPM and twice the available voltage at the plug. -50F To 300F Working Temperature Range,...

Reproduction single port vacuum advance for most all 1967-71 Ford V-8 engines. Fits Ford's brand of Autolite and Motorcraft distributors found on all 1967-71 Mercury Cougar and V-8 Ford Mustangs.

New Old Stock upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

Reproduction upper distributor bushing for many V-8 engines 1958 through 1973. All 289 distributors 1965-67 should have one installed, 302's up until 1973 or possibly later. All FE distributors, including 352, 390, 410, 427, 428.  * Note - 351W and 351C engines and 429/460 engines used a different upper bushing. See related items for that listing. Replaces Ford part number B8QH-12120-A. We measure 0.687" O.D., 0.468" I.D., and 1.750 long. ...

Reproduction upper distributor bushing for 1969-73 351W, 351C, 429, and 460 Ford V-8 engines. * Note - 260/ 289 / 302 / 352 / 390 / 410 / 427 / 428 engines, all used a different upper bushing. See related items for that listing. Replaces Ford part number  C5AZ-12120-A. We measure 0. O.D., 0." I.D., and 1.750 long.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #107 or DF-342, single points cam with weights marked 13L and 18L from the top. Factory used on small block and FE distributors.  Ford part number C5AZ-12210-A.

New Old Stock distributor cam and weight assembly for many Autolite and Motorcraft distributors. This is cam #108 or DF-343, single points cam with weights marked 10L and 15L from the top. Factory used on small block and FE distributors.   Ford part number C5AZ-12210-B.

New Old Stock Autolite distributor cap for the 1964, 1965 1966 Ford and Mustang. Technically a service replacement cap, this cap has aluminum contacts, not brass. Fits all Ford V8 engines 1957-73. Before and beyond. Does not have "AUTOLITE" on the cap, just a "1", typical cap used 1957-1966 of Ford V-8's. Ford part number B7A-12106-A. 

Exact copy reproduction concourse correct distributor cap with raised Autolite logo. Good for all 67 - 73 Cougars and Mustangs. A must have for anyone building a show car.

New Old Stock MOTORCRAFT distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang. Technically a service replacement cap, this cap has an embossed "MOTORCRAFT" on top. Fits all Ford V8 engines 1967-73. Before and beyond.Ford part number B7A-12106-A. 

Reproduction distributor cap for the 1967 - 1973 Mercury Cougar or Ford Mustang