1969 Ford Mustang

Used bracket for holding either the emergency flasher or turn signal flasher on many Fords dating from 1963. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches to one of two different relay mounting brackets. Couple of different designs were also used. Additionally there is also a different style of flasher mounting bracket. See our related items.Replaces Ford part number C3AB-13351.

Used bracket for holding either the emergency flasher or turn signal flasher. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches directly to the rear of the metal dash with a hex head machine screw.Replaces Ford part number C8AB-13351-A.

Powder Coated. Replaces Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

Used lower quarter window bracket for any 1969-70 Mercury Cougar and Ford Mustang non-fastback. This is the lower bracket that mounts to the bottom of the stationary slider bracket. This bracket adjusts the top movement in and out of the rear seat glass. Power or manual crank, hard top or convertible, driver or passenger side. Minor variation on this bracket, some are flat, some have a curve in the vertical edges on both sides. One bracket per window, same for either side. Replaces Ford part...

Bare metal power steering hose bracket for any 1967-69 small block Mercury Cougar or Ford Mustang. 289-2V, 289-4V, 302-2V, 302-4V, 351-2V, and 351-4V. No rubber insulator included.

For 1969 351W engines only. This bracket will physically work with any 1967 - 68 289 or 302 engine, but for 1969 the bracket should not have a large stamped hole through the middle. Ford master part number C7AZ-3C511-A, same part number as the 289/302 bracket with the deletion of the large hole. Ford intended to have a casting number stamped on these brackets and it would be C7AA-3C511-C. For restoration purposes, this bracket was factory painted satin black.

Perfect fit for use with AC or non-AC 67, 68, 69, or 70 Cougar with the 390, 427, or 428 big block.

This cast bracket bolts to the frame on the driver side and anchors the power steering hydraulic cylinder. One of the benefits of buying parts from Western parts cars is that they have not been corroded by salt! This part comes "as taken from a parts car". At least two variations of this bracket (see photos above) between 1967-70. Our observations show the version with the curved casting number version orientation to be from 1970 Cougars with were all built in Dearborn, Michigan. The...

This is a decent reproduction of the radio bracket for the 69 or 70. Take a look at the smaller image to see them side by side. The repro is slightly taller and has extra holes in it so it fits other applications. We recommend sticking with good originals.  Why deviate from 100% correct if you don't need to.

Take a look at the smaller image to see the repro and used side by side. The repro is slightly taller and has extra holes in it so it fits other applications. Why deviate from 100% correct if you don't need to. Ford Part # C9ZZ-18842-A.

Used bracket for mounting the rear axle flexible brake hose. This is a factory welded in bracket that was removed from a 1967-69 Mercury Cougar or Ford Mustang. Double check your placement for your particular year, when welding the bracket to your car. Good used bracket the you need to separate from the factory spot welds. Part bead blasted for photo, has correct "D" shaped hole for indexing the flexible brake hose to rear axle. Ford part number C7ZZ-2A051-A.

Grade A, Rear stop bracket for driver side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, included. Felt and rubber dipped section will be in good but not great shape. The felt strip really takes a beating. Please see related listing for plate only or B grade bracket without hardware. Ford part # C9ZZ-65222A55-A. Do you have questions about Glue-In vs Bolt-In glass?...

Grade B used. Rear door window stop bracket. Stops the window in the up position. Application driver side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. Plan on replacing the felt, the rubber dipped section will also probably be cracked. One per door. Plate and bolts not included. Please see related listing for plate only or complete stop bracket assembly. Ford part # C9ZZ-65222A55-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to...

Grade A, Rear stop bracket for passenger side door window. Stops the window in the up position. Application passenger side door glass 1969-70 Mercury Cougar and Ford Mustang including Mach 1. One per door. Plate and bolts, included. Felt and rubber dipped section will be in good but not great shape. The felt strip really takes a beating. Please see related listing for plate only or B grade bracket without hardware. Ford part # C9ZZ-65222A54-A. Do you have questions about Glue-In vs...

Used bracket for holding relays, either the emergency flasher or turn signal flashe. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This is one of two different brackets used for holding relays or flasher brackets. See our related items.Replaces Ford part number C9ZZ-14A301-A.

Used bracket for holding relays, either the emergency flasher or turn signal flasher. We find these mainly in 1970 Mercury Cougar and Ford Mustangs. This is one of two different brackets used for holding relays or flasher brackets. See our related items.Replaces Ford part number D0ZZ-14A301-A.

Used bracket for attaching the steering column upper bracket to the brake pedal hanging bracket. Has a slot as shown. Fits all 1969 Mercury Cougar and Ford Mustang with either tilt or fixed steering columns.Shows up in the exploded views as Ford part number 3678.

Used steering column to dash bracket. One year only, used on both fixed and tilt column cars.

Floor mounting column bracket for the 69-70 Cougar or Mustang. Rubber gasket may not come with bracket, and if it does will most likely need replacing. Undamaged with original fasteners. Get the gasket here.Ford part number C9ZZ-65017A50-A.

One year only design.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used original lower power steering hose mounting bracket for 289 / 302 / 351 1967-69. Comes as shown with rubber insulator. This used version has the indexing tab which the reproduction does not. May come with new bolt and or rubber insulator.Replaces Ford part # C7DZ-3A609-A, C7DZ-3A610-A, C7ZZ-3C510-B, and C8ZZ-3C510-A.

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

Used lower bracket for installing the rear interior panels on any 1969-70 Mercury Cougar or Ford Mustang convertible. One bracket per side. These brackets will have a bit of dirt and or rust on them, originally painted chassis black. See related upper bracket.Replaces Ford part number C9ZZ-76310A84-A. 

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific. 

Rear Wheel Cylinder (7/8", Left Rear). For 10 x 1-3/4 inch rear drum brake shoes. Typically 1967-68 Mercury Cougar or 1967-73 Ford Mustang with 289/302 cubic inch engines or smaller.The difference in this premium version and the economy version, is that this cylinder will be concours correct and have the smaller 1/4" fitting. Replaces Ford Part #: C20Z-2261-B, C3AZ-2261-B, C4TZ-2261-A, C60Z-2261-A, D3TZ-2261-A, D3ZZ-2261-A. ...

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/2 inch drum brakes. This unit fits into a 1-3/32 inch hole on the brake backing plate. Replaces Ford Part # C6OZ-2062-B or C9TZ-2062-B.

Reproduction driver side (left hand) front wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits in a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part #: C3OZ-2062-B, D2ZZ-2062-A, & D3ZZ-2062-A.

Reproduction passenger side (right hand) wheel cylinder for 10 inch x 2-1/4 inch drum brakes. This unit fits into a 1-1/8 inch hole on the brake backing plate. Replaces Ford Part # C3OZ-2061-B, D2ZZ-2061-A, & D3ZZ-2061-A.

Rear Wheel Cylinder 29/32 inch bore, right hand fits passenger side of any 1969 with 2 inch wide rear brake shoes. This wheel cylinder orients the hard line to the rear of the vehicle. 1970-73 wheel cylinders are oriented towards the front.

Reproduction drum brake backing plate hole cover plug. Replaces Ford Part # 8A-2092.

Used driver side (left hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar or Ford Mustang, and Fairlane / Torino equipped with 351 or larger V8 engines. Ford part # C9OZ-2013-B. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

Used passenger side (right hand) front drum brake backing plate for 2-1/2 inch brake shoes on the Mercury Cougar, Ford Mustang, and Fairlane / Torino equipped with the 351cid or larger V8 engine.Ford part # C9OZ-2012-A. *NOTE* Excludes 1969-71 Mustang and other Ford/Mercury with 302 engines, which normally came with 10" x 2-1/4" drum brakes on the front.

If you watch our booster video you will see we have a clear distaste for most of the offshore boosters offered today. What caught our attention about this new product was that it looked like a real deal 67-9 Midland brand booster! We went the next step and sent it to the world's foremost leading authority on said boosters (Booster Steve in Portland OR) so he could put it through some rigorous testing and examination. At first he was very hesitant to have us waste the postage to send it but two...

Quality rebuilt LH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out out video on converting from drum to disc brakes below: ...

Quality rebuilt RH disc brake caliper for 1968-1973 Cougar / Mustang. Hardware not included. Check out out video on converting from drum to disc brakes below: ...

Replaces Ford Part # 382713-S Sold individually

Sold as a Pair. Ford Part #: C8AZ-2B296-A

part# 384114-S100 Sold individually

Used disc brake distribution block for 1968 and 1969 Cougar and Mustang with factory disc brakes. Mounts to the driver side fender apron with two nuts. Bare block without brake switch or Proportioning valve. Look for our listing for 1968 - 1969 Brake Distribution Block Assembly for a unit with the switch and proportioning valve with steel flared connecting lines. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # C8ZZ-2B257-A. Here’s a video to help you...

Used drum brake distribution block for Mercury Cougar and Ford Mustang with front drum brakes. This unit mounts to the driver (left hand) side fender apron with a single bolt. Bare block without the brake switch. Plan on testing and or rebuilding before installation. Rebuild kits available.Ford part # C8ZZ-2B257-B.Here’s a video to help you rebuild the distribution block so that you can corral your Cat or Pony without fearing for your life. ...

Reproduction disc brake distribution block and proportioning valve assembly for the Mercury Cougar or Ford Mustang with factory disc brakes. This will also work on your 1968 - 1969 Fairlane / Torino / Montego / Ranchero / Cyclone & Cobra equipped with power disc brakes in the front if you carefully remove the wedged on stamped steel mounting bracket and reuse your original bracket. Mounts to the driver side fender apron with two nuts. With this assembly you will get a distribution block, brake...

Clever tool that keeps the piston stationary in your brake distribution block. It is as simple as centering the piston and screwing in this tool, of course your have to catch the groove in the piston. Leave in until brakes are completely bled and functioning. Remove and install your brake warning light switch.

These new brake drums are perfect replacements for tired and thin originals on you Cat or Pony. Fits cars with either the 2 1/4 inch or 2 1/2 Inch shoes. Front drums do not include studs or a hub. Drums Provide Consistent Quality & Reduced Noise.; Drums Are Vehicle Specific & Meet Federal Safety Standards.; Castings Meet Sae J431/g3000 Specifications For Proper Tensile Strength.; Machined To Control Perpendicularity & Run-Out For Optimal Performance & Brake Life.Also fits V8...

Quality replacement brake drum. # of Bolt Holes : 5 Inside Diameter : 254 mm Bolt Circle Diameter : 114.3 mm Brake Drum Surface Depth : 71.6 mm Center Bore Diameter : 61.8 mm Maximum Discard Diameter : 256.3 mm O.D. : 296.3 mm Replaces Ford Part #:C2OZ-1126-B

7/16-24 Fitting on Axle Lines. STOPFLEX?? incorporates a special 4 layer design for superior strength and virtually no volumetric expansion. It starts with a Teflon PTFE core (liner) which is wrapped first in a Kevlar braid, followed by an elastomer barrier and then it's strengthened further by the outer stainless steel braid. Replacing original equipment rubber hoses with STOPFLEX?? stainless steel braided hoses will increase braking performance by doing away with the soft spongy brake pedal....

28 Spline Rear Axle 3/8-24 fitting on Axle Lines. STOPFLEX® incorporates a special 4 layer design for superior strength and virtually no volumetric expansion. It starts with a Teflon PTFE core (liner) which is wrapped first in a Kevlar braid, followed by an elastomer barrier and then it's strengthened further by the outer stainless steel braid. Replacing original equipment rubber hoses with STOPFLEX® stainless steel braided hoses will increase braking performance by doing away with the soft...

Flexible high pressure replacement brake hose for front drum brakes that fits both passenger (right hand) and driver (left hand) sides of Mercury Cougar or Ford Mustang. Sold individually, please remember to order two if a pair is needed.Replaces Ford part # C7ZZ-2078-A.

Flexible high pressure replacement brake hose for the front driver (left hand) side of Mercury Cougars or Ford Mustangs equipped with disc brakes.Replaces Ford part # C8ZZ-2078-B.