Bumpers & Trim

Bolt for installing the front bumpers on any 1969-70 Mercury Cougar or Ford Mustang. Threads into the front frame rails. 4 needed per car. Sold individually#56362-S

Fits all models.

Reproduction Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang.If you're working on both sides of your grille, you will need two kits, one kit will do one half of the grille.

Reproduction Headlamp Housing Grille Bolts & U Nuts for the 1969 Mercury Cougar / Ford Mustang

Powder Coated. Replaces Ford Part Number: C9ZZ-17385, correct for a 1969 Mustang or Cougar but works fine on a 1970 Cougar.

This bumper bolt is sold individually and replaces Ford part # C4ZB-17758-A. It features the correct "button" head profile covered in stainless steel. Silver zinc with wax coating to extend plating life. Reduced shoulder height allows the nut to seat properly.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more...

C9WY-17767-A Front bumper mounting arm, 1969 Mercury Cougar driver side. This will work fine on 1970 Cougars, but technically the 1970 bracket has a rectangular hole for a anti rattle piece of rubber for the stone guard.

C9WY-17766-A Front bumper mounting arm, 1969 Mercury Cougar passenger side. This will work fine on 1970 Cougars, but technically the 1970 bracket has a rectangular hole for a anti rattle piece of rubber for the stone guard.

Hardware for mounting the hood bumpers on the radiator core support. Clip mounts with threads down, nut on top. Sold as a Kit as Pictured.

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This listing is for a bag of 25 clips. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare....

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.This particular clip is used on many Ford cars throughout the 60's and 70's.This listing is for a box of 100 clips. We recommend buying...

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B.Sold Individually.We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.

Fits Standard and XR7

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

Attaches behind the drivers side horn on all 1969-70 Mercury Cougar and Ford Mustangs with air conditioning. We believe that this part was installed to maintain clearance with the A/C condenser. Ford part number C9ZF-13925-A as seen in the 1969 Electrical Assembly Manual.

The POGO Stick works just like the larger Hustler stick but is much easier to ship. If you need more leverage you can just add a pipe for leverage. We will loan this hustler stick for 60 days, with a 100% refundable purchase price. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Check out our video below: ...

These plates were really clean before they were sent out for restoration, you can get  your Oregon plates restored at http://oregonplates.com/NOTE: The plates and plate numbers pictured are exactly what you'll receive.

Give your Cougar or Mustang that cool, classic look by adding these replica California black and gold license plates. These plates are favored by classic car owners everywhere, because they signify a rust free, restored classic car. These plates are real stamped aluminum with raised numbers and letters. Sold Individually.

This part is what holds on 1969 - 1973 Mercury Cougar / Ford Mustang Rear License Lamp Lens.  Replaces Ford part # C5OZ-13566-B or C4AZ-13564-A.

Because these pieces are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503137-A. *NOTE* If you have questions about your cores, checkout our video below. ...

Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. Restored passenger side (right hand) vertical windhield moulding / trim for the Mercury Cougar. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. When you purchase one of our stainless trim parts you are paying for the removal of dings and scrapes as well as the polishing of the part.  Ford part # C9ZZ-7603144-B....

Restored passenger side (right hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang coupe. Because this windshield moulding / trim is a restored original piece, it will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. They are also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503136-A. *NOTE* If you have questions about your cores, check out our video below. ...

Because these upper windshield mouldings are restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly. This package is also an excellent option for you Mustang owners as well. Ford part number C9ZZ-6503144-A. *NOTE* If you have questions about your cores, check out our video below. ...

Restored stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together.  We only sell this item on an exchange basis only, you are required to pre-send your restorable cores to West Coast Classic Cougar. These restored pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7...

This option REQUIRES sending your cores in advance. Used stainless steel convertible top trim for the middle section of the exterior boot trim. This is a two piece set of trim, a right and left section, which slip fit together. These pieces work with both the 1969-70 Standard model Cougar and Mustang boot mouldings (even the reproduction die cast chromed mouldings), and 1969-70 Mercury Cougar XR7 convertible top mouldings. Limited supply of used and restored available.Replaces Ford part...

Used driver side (right hand) convertible top boot moulding / trim for the Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

Used passenger side (right hand) convertible top boot moulding / trim for the Mercury Cougar or Ford Mustang convertible. No cracks or missing studs, driver quality chrome. We also have some that need re-chrome as well as some singles, please call for details. Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores.*NOTE* If you have questions about your cores, checkout our video below. ...

This good used plastic trim part has been inspected for cracks and scrapes and has been found to be in good used condition. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted. This is the driver side, outer vertical piece for all 1969 Mercury Cougar and Ford Mustangs. 1970 has a different part number, but looks the same. We also sell the 1970 piece with D0Z.. casting number.

This good used plastic trim part has been inspected for cracks and scrapes and has been found to be in good used condition. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted. This is the passenger side, outer vertical piece for all 1969 Mercury Cougar and Ford Mustangs. 1970 has a different part number, but looks the same. We also sell the 1970 piece with D0Z.. casting number.

Used exterior driver side (left hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the bottom...

Used exterior passenger side (right hand) header moulding / trim for the Mercury Cougar or Ford Mustang convertible. If your stainless parts have no real damage you may consider investing in a free standing buffer and polishing kit. With a bit of elbow grease and time, you can make those trim pieces look better than new! Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. *NOTE* These do not pry off! The fasteners are located on the...

Black is currently out of stock. We have green. This good used plastic radio trim part has been inspected for cracks and scrapes and has been found to be in good used condition. These original parts are better quality than the repros and unlike the reproductions you can buy them individually. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted.

Currently out of black. Our used plastic radio trim piece has been inspected for cracks and scrapes and has been found to be in good used condition. These original parts are better quality than the reproductions, and unlike the reproductions, you can buy our used trim parts individually. Please select a color and we will attempt to accommodate. Plan on these used plastic parts needing to be painted.

Contoured stainless steel trim for the driver side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A15-A Our grade B door glass trim for 1969 will have heavy scratches that will not come out and the small bend over tab at the top will be bent or missing. The part will not be broken and will function just as good as our grade A part. Here is the 3M product used to glue this trim to the glass.Ford part #...

Contoured stainless steel trim for the passenger side door glass. Application all 1969 Mercury Cougar and Ford Mustang hard top and coupes. See accompanying rubber seal Ford part #C9ZZ-65214A14-A Our grade B door glass trim for 1969 will have heavy scratches that will not come out and the small bend over tab at the top will be bent or missing. The part will not be broken and will function just as good as our grade A part. Here is the 3M product used to glue this trim to the glass.Ford part #...

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes, will not lineup with factory holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications they can be made to fit your 1971 - 1973 Mercury Cougar.

NOTE: Some modification required to fit Cougars!This is the wheel lip mouldings for the 1969 Mustang. With very slight modifications (drilling extra holes) they can be made to fit your 1971 - 1973 Mercury Cougar.

Restored driver side (left hand) lower windshield moulding / trim for the Mercury Cougar or Ford Mustang. This unit is basically the same as the coupe version, but this convertible unit has about and inch and a half cut off the end. Because these lower windshield mouldings are lovingly restored original pieces, they will have far superior fit and finish when compared to "offshore" reproductions that do not fit correctly and just plain old look like crap. They are an excellent option for you...

This driver side lower windshield moudling core is a great candidate for restoration for you do-it-yourselfers out there looking to save a buck. Or if you're driving around in a lower quality daily driver and you're missing this piece, we got what you need. Ford part number D0ZZ-6503149-B.