Heating & Air Conditioning

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. 

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Used air conditioning evaporator core, for most of the 1969 model year and all of 1970. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have...

Used air conditioning evaporator core, for most of the 1969 model year. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have corrosion from a...

Exact replacement to original dryer. Drier removes moisture and should be changed anytime system is recharged. It is the life of your system. Stainless steel filter element. Filter stops contaminants from clogging expansion valve. Replaces part # C9ZZ-19959-A.

This unit is a reproduction concours correct A/C discharge hose for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, C9ZA-19972-C or C9ZA-19972-E, both are the correct part number. This hose is approximately 20 inches long. Ford part # C9ZZ-19972-C.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine from 1969-73. Original condensation drain hose from the A/C case, through the floor board, to the ground. Replaces Ford part # C9ZZ-19858-C.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Ford part # C9ZZ-19858-C.

Regardless of which V-8 engine, C9ZA-19837-A or C9ZA-19837-C both are the correct part number. This hose is approximately 68 inches long. Ford part # C9AZ-19837-A.

A/C suction line for the evaporator to compressor for the 1969 Mercury Cougar or Ford Mustang with any V-8 engine. This hose is approximately 55 inches long.Ford part # C9ZA-19867-A.

For 1969-70 Mercury Cougars and Ford Mustangs with the 351W engine. This is an Eaton manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 6", and an overall thickness of 2-1/16 inches. Ford part # C9AA-2981-F.

For 1969 Mercury Cougars and Ford Mustangs with the 351W engine and also for 1970 Cougars and Mustangs with the 351W or 428CJ engine. This is a Pitts manufactured pulley and clutch assembly with a pulley diameter of 6-5/16", a clutch diameter of 5-3/16", and an overall thickness of 1-1/2 inches. Ford part # C9AA-2981-D1. May also have part # C9AA-2981-D2.

Grade B A/C vacuum canister that has a non working check valve. Suitable for filling the hole in your passenger side fender apron. This A/C vacuum canister mounts through the passenger side fender apron near the hood hinge. This vacuum reservoir controls, damper doors inside the A/C unit. This unit includes a built in check valve. Used and not holding vacuum, tank and bracket, also known as the A/C vacuum reservoir. Fits all 1968-70 Mercury Cougars, and is a replacement for 1967's...

This A/C vacuum canister mounts to the passenger side fender well and controls doors inside the A/C unit. This unit includes a built in check valve. Fits 1968-1970 Mercury Cougar and Ford Mustang. The collapsing or imploding problem has been resolved on this vacuum reservoir with the addition of the ribbing for strength.  Replaces Ford part # C8ZZ-19A566.

Complete vent includes mounting hardware. These are sold individually, so please choose between driver and passenger side. We do not guarantee the felt strip to be in place (see picture for example) and we do not guarantee good chrome finish on the louvers. We do inspect them carefully for cracks. Ford part # C9ZZ-19893-D driver side, C9ZZ-19893-C passenger side. *NOTE* The leading edges of the round plastic register are chromed. Often the chrome will wear off, but if you rotate the register...

Complete vent includes mounting hardware. These are sold individually, so please choose between passenger and driver side. We do not guarantee the felt strip to be in place (see picture for example) and we do not guarantee good chrome finish on the louvers. We do inspect them carefully for cracks. Ford part # C9ZZ-19893-C passenger side, C9ZZ-19893-D driver side. *NOTE* The leading edges of the round plastic register are chromed. Often the chrome will wear off, but if you rotate the register...

Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.

Complete heater and air conditioning control assembly includes bezel or face plate, bracket control mounting plate, electrical and vacuum switches. Functional, driver quality, heater control assembly. Expect some degree of wear and tear on the plastic chrome knobs and lever borders. Does not include the indicator light plug and harness. Knobs, if included may not be in the greatest shape. We suggest purchasing the new reproduction knobs. Ford part # C9ZZ-19A884-A. *Restoration Tip* For...

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1969-70 variety, which have specific colored wires and leads....

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Used heater blower motor for 69 - 70 Mercury Cougar and Ford Mustang. The reproduction off-shore motors may or may not prove to be as good of value as these good used original FoMoCo motors. To date, all we can find for these cars are foreign made units. Keep in mind our used motors carry a one year warranty and the new motors have a 30 day warranty. Also know that the mounting plate is included for free just for the asking on these used motors. We personally have never used the reproduction...

Used bracket or mounting tab that often gets lost when servicing the air conditioning plenum. Attaches to the box with two screws and has stud that goes through the engine firewall for mounting the A/C box assembly under the dash. Basically the same part as found on 1967-68 brackets, but this one has a slightly longer stud. Replaces Ford part number C9ZZ-18A456-A.

Used bracket for installing the defrost nozzles assembly to the dash on all 1969-70 Mercury Cougar or Ford Mustang with factory air conditioning. Bracket only, no attaching hardware.

Clamp for supporting and connecting the hard line from the dryer and the suction hose from the condenser.. Two piece clamp with screw. No actual Ford part number listed in the MPC or assembly manuals, the basic part number would be 19B632 though. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon...

Used rubber bumper that fits into the bracket in the bottom center of the door shell. Fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustangs. This is the rubber bumper for the window rest when the door glass is at its lowest. Bracket is in bottom of the center of the door. Fits both right and left doors. Correct for 1967 - 1968 but will work in 1969 - 1970 with Bolt-in glass if you cut it down. Sold separately, two required per car. Replaces Ford part # C5ZZ-6521762-B  Check out...

Concourse correct 3" long nipple that installs in the water pump, with the correct plating.C8OZ-18599-A.

Heater cable for Cougars and Mustangs that are not equipped with factory air conditioning. Ford Part #: D1ZZ-18518-A

Used air conditioning distribution chamber. Comes as shown, plastic housing, internal flapper door with rod, with attached bracket for attaching vacuum actuator. Actuator, lever, and hardware sold separately. Unbroken condition, it will definitely need new foam on the door.Replaces Ford part number C9ZZ-18471-A.

This A/C tag clip fastens the aluminum tag to top of the A/C pump.

Special clip for attaching the pull cable to the right or left fresh air vent on any 1969-70 Mercury Cougar or Ford Mustang.

Clips that attach to the dash for mounting the defrost nozzles. Package of 3 clips and nuts. Good for cars with or without A/C. Typically found on 69-73 cars, but will also fit and work on 1967-68 as well.Replaces Ford part number 357849-S100.

Core used set of Eaton clutch brushes, we save these because of the FoMoCo stamped bracket with Ford part number C7AA-2979-A. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to reproduction version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for NEW Eaton brushes. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

This set of brushes only fits the Eaton brand of air compressor clutch. These are exact reproductions made from the original tooling. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to this version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for core brushes with stamped Ford numbers. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

Our new high performance condenser kit comes pre-assembled with the drier and all brackets. 1967 - 1968 condenser shown. These condensers are one of the highest performing, durable condensers available in today's automotive market. This condenser was designed specifically to increase heat transfer for lower head pressures during idle situations, allowing more airflow to pass through the condenser and give the radiator enough airflow to operate properly. Remember to remove your coupler...

Original used female half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

A/C compressor clutch decal for Mercury Cougar and Ford Mustang.Replaces Ford Part #: C7AA-2987-D.

Blower door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The blower door allows air to pass to the duct tubes from the center blower motor housing. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, will have good rubber seal as shown. Door only, shaft not included, but available. See related parts.Replaces Ford part number C7ZZ-18B254-A.

Air inlet damper door for any 1969-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The damper door allows re-circulating or fresh air to enter the fiber glass A/C box. Dimensionally the same as the 1967-68 door, but with two small notches, instead of one. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare...

Evaporator door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The evaporator door allows air to pass over the evaporator in the A/C box. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only, shaft not included, but available. See related parts.Replaces Ford part number...

Heater door for any 1967-73 Mercury Cougar or Ford Mustang with factory or integral air conditioning. The heater door allows air to pass over the heater core in the A/C box. This is the smallest door in the A/C box, and the one subject to the most damage from moisture. Part cleaned for photograph, normally will ship 'as removed'. Inspected for excessive rust pitting or weakness of the metal, they all will have a slight amount of metal degradation from being assembled as bare metal. Door only,...

This A/C evaporator drain hose is molded flex hose similar to the original, but it will need to be cut to the proper length. It is correct for 67 - 68 but can be made to work on 69 - 73. Replaces Ford part #: C7ZZ-19858-C or C8TZ-19858-A.

Lower heater duct to floor outlet for Cougars and Mustangs with air conditioning. Used grade "A" part and may have one very minor defect. This part will be damage free. Replaces Ford part number C9ZA-18C366-A.