Your cart is empty!
Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.
Reproduction 289 - 302 Alternator Bolt w- Smog for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold individually
Nice reproduction oil dipstick made from all steel, painted Ford engine blue. Only fits 289 or 302 Ford engines from 1967-73. These dipstick tubes have the 'full' and 'add' markings in the correct place, however they do not have any Ford part numbers stamped on them. Black steel as shown, not plain shiny steel like originals. Replaces Ford part # C7OE-6750-B or C8OE-6750-B.
NOTICE: The supplier is no longer making the previous version of the upper hose, and the new hoses will have more of a textured outer wall.These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal conditions, imprint will not come off even when in contact with antifreeze. All have...
New One-Piece, Rubber Coated Fiber Oil Pan Gasket for the 390, 427 or 428 FE Big Block engine in the 1968, 1969 or 1970 Mercury Cougar and Ford Mustang. 3/32" thick.
3/8-16 X 7/8 9/16 AF .75 OD Sold individually. Fits all 390 & 428. Replaces Ford Part #: 374409-S.
OEM Style Oil Pan Gasket.
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds
Spark Plug Wire Separator Brackets for the 1969 - 1970 Mustang Cougar or Torino with 428CJ Finned Aluminum Valve Covers, 1969 - 1970 Mustang Boss 302 with Finned Aluminum Valve Covers or Boss 351 models. These are an MCA approved unit made here in the USA. These replace Ford part number C9ZZ-6583-A and include both brackets and the 4 screws to properly install these units. Attaches spark plug wire holder to the factory finned aluminum valve covers
Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.
Concours correct Autolite spark plug wires for any 1969 Mercury Cougar or Ford Mustang with 428CJ engine with thermactor smog system. Black wires with 'Autolite', 'radio resistance', cylinder numbers individually imprinted, and dated 2Q68 (second quarter 1968) on the 7mm wires. Orange spark plug boots on this set.
Decal Text: Autolite EV-45 C8OZ-6A666-B Replaces Ford Part #: C8OZ-6A666-B.
Unique for the 1969 351 Windsor engines without air conditioning. Flat steel bar stock spacer that positions the power steering pump a measured distance away from the cylinder head. The bars are 3-3/8" x 3/4" x 1/2" in size. The threaded hole in the center is tapped 3/8-16. The two outer holes for attaching to the cylinder head are 11/33" holes on a 2-9/16 inch center. Verify the pre-tapped holes in your cylinder head if making your own spacer. For 1970, a round spacer was used, as could be...
The Proper ignition advance curve is vital for maximum performance, economy (gas mileage) and drive-ability. Ford / Mercury owners had few acceptable choices with regard to adjusting the vacuum curve with their OEM distributor. You could fumble with the stock washers, fiber stops and springs (a hit-or-miss exercise in frustration!) or you could spend the money on an adjustable after market vacuum advance that looks completely out of place and cost you major judging points. This works on any...
Perfect fit for your 289, 302, or 351w with or without AC but a hard sell when our good used rust free brackets cost less . . .
Used alternator adjusting bracket for any 1969 Mercury Cougar or Ford Mustang with 351W V-8 engines. This C9OE-10145-A stamped bracket is correct for all H or M code 351 Windsor engines. Will also fit 1969 F code 302 Ford engines too.Ford part number C9OE-10145-A.*Trivia - All 3 small block alternator adjusting brackets from 1965-1969 will fit most all 289 / 302 / 351W engines unless your engine has one of the larger pulleys. ...
Used alternator adjusting bracket for any 390 engine 1968-69 Mercury Cougar or Ford Mustang without factory smog. Specifically this is for 1968 390-2V or X code engines, and 1969 390-4V or 390IP engines offered in 1969 cars with S code designation. Replaces Ford part number C8AE-10145-A.This is the 411 for 1968-69 alternator mounting on Mustang and Cougar with 390 engines. If your 1968 S code car (390GT or 390-4V) was delivered in the United States (meaning not Canada or other foreign...
Application is 1967 - 1968 289/302 and 1969 Boss 302 Eliminator alternator adjusting with factory air injection emissions. Casting number C6OE-10145-A, Ford part number C6OZ-10145-A.
C8AE-9B452-B Thermactor smog pump belt tensioning adjustment bracket. Application is for all 1968 - 1970 FE engines with factory installed thermactor smog systems.
Reproduction thermactor smog pump adjusting bracket for all 1968 Mercury Cougar and 1968 Ford Mustang with S code 390-4V engines. Additionally this bracket was also used on 1968-70 Mercury Cougar and Ford Mustang with 428 Cobra Jet engines. Quality made product. Ford number C8AE-9B452-B.
This air cleaner assembly never came from the factory on any Cougar, but was an over the counter option available from your Ford dealer. If you have a very nice hood blanket I would think twice before using it in conjunction with this air cleaner assembly as it will leave an imprint. To avoid this problem with small block cars you can use a lower profile carburetor spacer, but on big block cars this is not an option due to the already thin design of the factory carburetor spacer. This will...
Brand new exact reproduction of the 1969 Q-Code 428 Cobra Jet non-shaker air cleaner base. Works for Cougars, Mustangs and Fairlanes. Correct snorkel opening, breather port, three mounting studs and a port for the vacuum powered air inlet door. Sold as a stand alone base, does not include snorkel,vacuum motor and door.Ford part number C9ZZ-9600-H
This is a reproduction of the original Autolite parts decal that was located on the air cleaner.Fits the following models with a BOSS 302 or a 428 4 barrel Cobra Jet engine:1969 Cougar1969 Mustang
This is a reproduction of the original engine displacement decal. Yellow background with black logo followed by black background with white 302 4V followed by yellow background with black BOSS. Located on the top of the air cleaner.Fits the following models with a BOSS 302 engine:1969 Cougar1969 Mustang
Fits all V8s with oval air cleaner.
Reproduction stud and nut assembly that the factory line workers used for locating the air conditioning pedestal bracket. Then backed up with a nut. Used on 289 / 302 / 351W / 390 / 428CJ pedestals from 1967 - 1973. Stud is threaded into the cylinder head for easy installation of the cast iron pedestal bracket.*Note - Excludes 351C and 429CJ.
This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. * This filter fits primarily Big Block cars, but a couple of other combinations, so grab a tape measure and double check the height of the one you need to replace, as that will tell you which one you need. Air Filter Height (Inches) : 2.193" Air Filter Height (mm) : 55.7 mm Air Filter Bottom I.D. (Inches) : 11.32" Air Filter Bottom I.D. (mm) : 287.53 mm Air Filter...
These filters feature the correct color of filter paper and an red/orange molded face. In addition, they have the correct "round hole" design on the outer shell. Fits 289, 302, 351, 390, 427, 428 and 429 engines originally equipped with the chrome high performance air filter assemblies. Please note: this filter will NOT fit a standard Ford air cleaner Replaces Ford Part #: B7SZ-9601-A.
Correct dimensions, good fit. Will show minor cracks in rubber but will not affect performance and cannot be seen when installed. Replacement air cleaner for the 1967 - 1973 Mercury Cougar Walking Cat Oval Air Cleaner, as well as other Ford oval air cleaners.
This Filters Last 40% Longer & Holds 53% More Dirt Than Most other Filters. Please note that the Ford Service Replacement specs for this filter (Service Replacement # D7AF9601AA) are; Type: 67; Inside: 13.000; Outside: 11.200; Height: 2.795. All reproductions that we have found follow these specs, making the filter 1/8" taller than the original filters. These filters will function properly, but the lid will not seat properly. ACTUAL FILTER SPECS: Air Filter Height (Inches) : 2.822...
Remanufactured alternator for any 67 - 73 Cougar or Mustang. Specs: Rated at 55 ampsSingle V groove pulleyExternal fanPlug position at 5 o'clock
Nice American made reproduction bracket. Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines, all with Thermactor smog pumps. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.
Application - 1968 - 390-4V and 427-4V, and all 1968 - 1970 428 Cobra Jet engines. This is also referred to as the low mount alternator mounting bracket. It has the Ford stamped casting number of C8AE-10156-A. Ford engineering number is C8AZ-10156-A.
Contains nut, lock washer, and spacer. Fits all Ford alternators.
This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.
Replica of the Autolite battery Stay-Ful tag advertising that the batteries 'Need water only 3 times a year'.
C8AF-9600-G Standard air cleaner base for all 351 engines, H code 351-2V and M code 351-4V. About 17.84" inches in diameter. Identified with the square nuts welded on the inside for mounting the air cleaner snorkel. Otherwise the same as C8AF-9600-C. Ford part number C8AZ-9600-D.
Distributor base gasket and seal. For all Ford V8 engines.Will not fit Windsor engines.
Premium reproduction concourse correct high draw battery cables for the Mercury Cougar equipped with the 428 engine.
Each of these great OEM Style kits include all three required cables, proper terminal and post clamp ends. Unlike CONCOURS CORRECT cables, these do not have the Ford part numbers on them. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : C8ZZ-14300- ...
Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : C8ZZ-14300
This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.
Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang
Fits Standard and XR7
Perfect fit the first time. You will be happy with this Group 24, quality reproduction and check out the price! These battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Replaces Ford part #: C7ZZ-10732-D.
This is what I consider to be "Premium Quality". Very correct in every detail and made in the US! The group 27 larger tray was optional on any Cougar and standard on big block Cougars. Replaces Ford part # C9ZZ-10732-AR
Concourse Correct with 22, 24 & 27 series batteries for Mustang, Cougar and Shelby GT350/500 made in the USA to original Ford Specifications, includes attaching bolts. Replaces Ford Part # C9ZZ-16060-A or C9ZZ-16052-P .