1969 Ford Mustang

Concours Correct Spring attaches snorkle thermo door to Snorkle Base Replaces Ford Part # C8AZ-9A652-B

NOS Motorcraft condenser for point type distributors on any 1969-73 Mercury Cougar or Ford Mustang with V8 engines. Ford part number C9AF-12300-B and C9AZ-12300-A.

Our new high performance condenser kit comes pre-assembled with the drier and all brackets. 1967 - 1968 condenser shown. These condensers are one of the highest performing, durable condensers available in today's automotive market. This condenser was designed specifically to increase heat transfer for lower head pressures during idle situations, allowing more airflow to pass through the condenser and give the radiator enough airflow to operate properly. Remember to remove your coupler...

Original used 390 or 428 Cobra Jet piston connecting rod. These are marked C7AE-B. Rods and caps only. We strongly suggest using ARP aftermarket rod bolts. Limited quantity available, call to inquire. Replaces Ford part number C7AE-B and C6AZ-6200-C. *Note - Excludes 428 Super Cobra Jet engines.

The picture above shows these bumpers installed in the 100% correct reproduction console that we sell. These are sold individually, 2 required per car. Replaces Ford part # 379919.

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

Exact reproduction horn ring contact components for the standard horn ring used on two spoke steering wheels, replaces Ford part # C9AZ-13A805-B. Includes new hardware

Horn ring contact components for the standard horn ring found on 68-69 2 spoke steering wheels. Ford part number C9AZ-13A805-B. Not as shiny as the reproduction kit but the price is less and the quality is FoMoCo original all the way!

A needed part for giving your car a tune-up.

A needed part for giving your car a tune-up.

New midland control hub assembly and disassembly tool for use with the 67 - 69 Cougar and Mustang Midland style booster

Used wiring pigtail with light socket for illuminating the heater and air conditioning controls on Mercury Cougars and Ford Mustangs. Tested and is ready to install. Includes the clip for securing wire to the control housing. Bulb 1445 sold separately.Ford part number C5AB-18541-A

Premium quality original FORD valve that has been re-manufactured to original tolerances. Quality part that is rebuilt by a true craftsman here in the USA. *NOTE: Our rebuilt and reproduction control valves all come pre-lubed with the correct amount of grease. If out of the box you add more grease, you will damage the valve. Unlike some suspension parts these are not designed to add grease until you see the grease coming out of the seal. Our warranty does not cover over lubricating. ...

Unfortunately we have had a high rate of returns due to failure on these and can no longer enthusiastically recommend them. Please consider our original rebuilt units. This is the large nut control valve that Ford switched to after 1967. Many 1967 Cougars have been converted to the 1968 valve over the years so you may want to double check your valve before ordering. These units are designed to use type F fluid, not off the shelf power steering fluid. Please follow the procedures for...

This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall, look for two dimples. Wiring is simple, unplug the windshield wiper harness and plug the male and female ends into the appropriate plugs on the controller. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper delay switch.Part # C9ZB-17C476, MPC #'s C9ZZ-17C476-B or D0ZZ-17C476-B.

Reproduction front tack strip for the front bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the front bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 feet (60 inches) of material and will have to trim the tack strip to fit...

Galvanized three piece replacement tack strips for the 1969 - 1970 Cougar convertible. Over-sized, must be shipped via UPS.

Reproduction tack strip for the rear bow of the convertible top on the Mercury Cougar or Ford Mustang convertible. When replacing your convertible top, it's also a good idea to replace the tack strips in the front and rear bows of the convertible top frame. This strip slips into the rear bow of the convertible top's frame and allows the fabric of the top to be attached to the frame. You will need approximately 5 Feet (60 inches) of material and will have to trim to fit your top. You can also...

Reproduction stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. Ford part number: C9ZZ-7654676-A

This is the restored stainless steel trim for the front of the boot that attaches to the back side of the back seat in a 1969 or 1970 Cougar and Mustang. This is a very hard part to come by in good shape. Many times body shops will lose this piece while replacing the top.Ford part number: C9ZZ-7654676-ATHIS ITEM WILL NOT SHIP UNTIL WE HAVE RECEIVED YOUR CORE. ...

Currently, Convertible Tops dropshipped from this supplier will not ship for 4-6 weeks. The original tops would have been double texture PinPoint Vinyl. There are 3 different materials currently offered for these premium tops. Single Texture PinPoint Vinyl (GOOD): This is the material that is offered by almost all Mustang Vendors and it looks the same on the surface as an OEM top. It is often referred to as an OEM replacement, but that is not exactly accurate...This is a two-ply composite...

This new single texture two ply denim convertible top is an inexpensive top that is only recommended if you car is going to be stored indoors.*NOTE* This is the convertible top only. Top bows, tack strips, and tension cables are NOT included with this item.Have you ever wondered how a convertible top is installed, or maybe considered trying it yourself? Check out our installation video below! ...

C9ZB-7653139-A is the part number for the drivers side, C9ZB-7653138-A for the passenger side. These will often break when one hydraulic lift cylinder malfunctions and the other is still working. This scenario will put the top frame in a bind causing one of these cast parts to break. We carefully inspect these before shipment for cracks, worn areas or corrosion.

We have found a new manufacturer of the convertible top boots that are supposed to fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

We have found a new manufacturer of the convertible top boots that fit much better than the boots we were previously selling. See Pics Below. Ford calls this part the "folding top dust hood". Made from original pattern. Features long lasting vinyl. Includes foam pads. We stock the black and white. All other colors are ordered on demand from the manufacturer. Please note that convertible boots never came from the factory with snaps (except the 6 on the interior panels), so any boot that comes...

C8SE-A 1. 1969 application is very early production (before 11/6/1968) 351 engines with the 20 inch radiator. 2. 1970 application - 351 engines with manual transmissions and 20 inch radiator. Fan description - 4 blades and 17-9/16 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C9OZ-8600-B. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C6AE-E Multiple applications over the years. 1. Later 1967 production cooling fan, generally used after 11/14/1966 on most 289 engine applications. 2. 1968 302 without air conditioning. 3. Mid year (after 11/6/1968) 1969 351 without air conditioning. 4. 1969 Early Boss 302 before 4/14/1969. 5. 1971 Cougar with 351 engine, without air conditioning. 6. **1973 Cougar 351-2V without air conditioning prior to 2/19/1973. Fan description - 4 blades and 17-1/2 inches in diameter. Ford master part...

C7AE-D, Fan description - 5 blades and 18 inches in diameter. Ford master part number C7AE-8600-D. These 5 blade flex fans usually came on full sized Ford and Mercury cars starting in 1967. Can be used on any engine with the proper spacer with fan shroud with adequate fan opening. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C8SE-B Applications: 1. 1968 289-2V engines with air conditioning or the extra cooling package. 2. 1969 Boss 302 Eliminator - after 4/14/1969. 3. *1970 Boss 302 Eliminator. 4. *1970 351 with or without air conditioning. Fan description - 5 blades and 17-5/8 inches in diameter. Ford master part number C8SZ-8600-B. Multiple dates available. *Note - 1970 Boss2 and 1970 351 owners, some time soon after the start of the year the exact same fan, but with casting number D0ZE-B was used. Check out...

C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C8OZ-8600-A.Check out our cooling system upgrade below: ...

Reproduction transmission cooling lines made of OE steel for the Mercury Cougar or Ford Mustang equipped with the 351W and FMX transmission. These are sold in pairs

Featured in this kit are all the basic items you need to convert your small block 1969 Cougar or Mustang from a 20" wide radiator with a fixed four blade fan to a 24" wide radiator with 3 cores and the MAXIMUM cooling big block, high performance 7 blade clutch fan. This setup was used on the highest horsepower drive-trains of the day including the Legendary 427 Side-Oiler equipped GTE and the 428 SCJ Drag-Pak equipped Cougars and Mustangs. This might sound like overkill for your small block...

Copper crush washer for all disc brake hoses and calipers 1968-73 Mercury Cougar and Ford cars like Mustang. Size 0.39" x 0.62" x 0.062". Four needed per car, two per side (one on each side of the disc brake hose end) sold indiividually.

Original used factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B596-A and C1SZ-19B595-A.Components also sold individually.

Original used male half of the factory air conditioning coupler for all 1967-73 liquid line or sight glass hoses. Brass construction, includes the plunger and spring. Also sold as a two piece kit which includes the male and female components. Replaces Ford part number C1SZ-19B595-A.

Replaces Ford part #C1SZ-13783. Replaces burnt, cracked or missing original lenses located above the rear package tray.  Two required per car, sold individually.

This is the chromed correct die cast construction for your 1969 Cougar, 1970-73 used plastic but these will fit fine and look better than the plastic units. Great Quality. Sold individually, two required per car. Part of the XR7 package. Available on other hardtop models, part of the Courtesy Light group option. Option included, engine compartment light, trunk light, map light and these rear quarter panel lights for the back seat. Replaces Ford Part #: C4SZ-13776-B.*Trivia Dearborn built...

These lights feature beautiful chrome bezels and bright white lenses. Mounting hardware, bulbs and sockets with pigtails are included. These were used on the XR7 and all Cougars equipped with Decor level interiors in 1969 and 1970. These are AWESOME reproductions worthy of the most exacting of restorations. You will be VERY happy with these lights. Sold as a pair. Replaces Ford Part #: C9WY-13776-A & C9WY-13777-AThese use a 212 bulb.Click on images to enlarge. ...

C9WY-13777-A-AGRADE Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Hardest side to find in primo condition most get dinged up from errant seatbelts. These are available in reproduction. Nice Quality!These use a 212 bulb. ...

C9WY-13777-A Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.

New Old Stock Left side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. These are available in reproduction. Nice Quality!Ford part number C9WY-13777-A. These use a 212 bulb.

C9WY-13776-A-AGRADE Right side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. These are available in reproduction. Nice Quality!These use a 212 bulb.

C9WY-13776-A Right side courtesy lamp assembly attached to the door panel of all 1969 - 1970 Cougars with either decor or XR7 interiors. Additionally found on 1969 - 1970 Ford Mustang with decor interiors which include Grande and Mach 1. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses. These are available in reproduction. Nice Quality!These use a 212 bulb.

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

Used pivot cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.