1969 Ford Mustang

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7M27, December 27, 1967.  Used 0.030 over bore 4.080" Ford 390 engine block. Years ago, it looks to have been fresh machined, with new freeze plugs. No paperwork, bare block. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date...

These Big Block motor mounts bolt to your engine block on the top side and to the motor mount (insulator) on the bottom side. These are very correct looking and fitting reproductions, much better than the $95 version you will find in most catalogs. Fits 1967-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines, will fit passenger side of 427 side oiler engine, driver side will work with modification. Original Ford part numbers C7ZZ-6046-A R.H., C7ZZ-6046-B L.H. 427 number for the left...

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

Used engine lift hook or hoist bracket for all 1969-70 351W engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. H code 351W-2V and M code 351W-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We also sell...

Used engine lift hook or hoist bracket for all 1968-69 390 engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. X code 390-2V, S code 390-4V, and W code 427-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We...

Assembly line used engine lift hook. Driver side 1969-70 with 428 Cobra Jet engines, including 428SCJ. Stamped with number C8OE-17K004-B, which is the second version. An earlier version was used on 1968 R code cars. Fits all 1969-70 Ford cars with either R code or Q code 428 engines. Cougar, Mustang, Cyclone, Torino, Talledega, Cobra, Fairlane, Montego, Ranchero etc. Attaches to the driver side exhaust manifold. There is also a passenger side engine lift hook, see related items.  ...

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Left hand bracket. Ford part number D0ZZ-6029-D. The original 1967 part number for this bracket was C7ZZ-6029-B.

Mount to the frame for supporting and mounting the FE 390, 427, and 428CJ engines. Also known as lower engine mounting brackets. For all 1967 - 1970 Cougars with 390 - 427 - 428 engines. Also includes 1967 with 289. Sold in sets. Includes one each: D0ZZ-6028-D & D0ZZ-6029-D engine frame brackets.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Right hand bracket. Ford part number D0ZZ-6028-D. The original 1968 part number for this bracket was C8ZZ-6028-B.

Reproduction pair of engine pedestals / frame brackets for the 67 - 70 big block V-8’s. Mounts to the frame for supporting and mounting the big block 390, 427 and 428 engines. Also known as lower engine mounting brackets. Sold as a pair.

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Left hand bracket. Ford part number D0ZZ-6029-C.

Reproduction pair of engine pedestals / frame brackets for the 68 - 70 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction engine mounts.

Factory stock for 1968 – 1970 small block V-8’s. Mounts to the frame for supporting and mounting the small block 289, 302, 351 engines. Also known as lower engine mounting brackets. We recommend this bracket for 1967 Cougars with 289. Sold in sets. Includes one each: D0ZZ-6028-C & D0ZZ-6029-C engine frame brackets. These are better quality and fit than the reproductions. *Converting to these mounts on 1967 Cougars with 289 or 1969 – 1970 convertibles with 351 allows the use of reproduction...

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Right hand bracket. Ford part number D0ZZ-6028-C.

[No Description Provided]

This direct replacement features a larger than stock diameter of 2-1/4 inches for increased performance. This is the H pipe only and is for any 1969 Mercury Cougar or Ford Mustang with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2-1/4 inch aluminized pipes and made from an original 1969 Cougar and Mustang with the 390 engine. We also sell this H pipe in a 2 inch diameter and have OEM style dual exhaust systems that include the H pipe,...

C9OE-9431-B 351W factory original cast iron exhaust manifold for driver side. For all 1969 and 1970 Windsor 351's.

C6OE-9428-A 390-4V factory original cast iron exhaust manifold for passenger side. 1969 390-4V IP only. Same as earlier versions, but with a 1969 date and chamfered opening for donut. No spacer needed.

C8OE-9430-D 428 Cobra Jet factory original cast iron exhaust manifold for passenger side. *Spacer required for installation.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Exact reproduction of Ford's free-flowing, high-performance cast-iron exhaust manifolds used on the 428 Cobra Jet, 428 Super Cobra Jet, and GT500 Shelby's. Concours correct with original Ford logo and part numbers cast into the manifolds. These manifolds are available in both early and late versions. The earlier version manifold has the correct spacer on the right side while the later version manifold does not.  Installs easily and eliminates clearance issues compared to headers....

For factory installed A/C on Mercury Cougars and Ford Mustangs. This unit functions great, but when compared to the NOS unit, you will see that it is cosmetically a little bit different. This uses the "O" ring style seals which are not included.Will work with both R12 and R134 systems.

Good used expansion valve with a 30 day warranty and a great option for the purist who wants to stay original! Several known versions of this valve at least two shown in photos.Fits 1969-70 Mercury Cougar and Mustang, 1968-69 Lincoln Continental.It is recommended that these valves be cleaned inside thoroughly, prior to putting back into service Replaces Ford part # C8VY-19849-A. aka YG-28

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install.  These are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

Driver side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Driver side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530057-A.

Passenger side quarter window extension bracket. Mounts in the door jamb, and holds the adjustment screw for the window guide.. Bracket for all 1969-70 Mercury Cougars and Ford Mustangs. Passenger side only. Includes bolts as shown, adjusting screw sold separately Fits hard top coupes and convertibles, N/A for fastback or sport roof Mustang. Manufactured by FabCo for Ford.Casting # is C9ZZ-6530056-A.

New clear plastic lens or face plate for the heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!

New clear plastic lens or face plate for the A/C and heater control on all 1969-70 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. *Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff wheel to carefully grind away the factory crimps. Use your safety glasses!

New clear plastic lens or face plate for the ultra rare Power Ventilation option, heater control with power vent on all 1969 Mercury Cougar or Ford Mustang. These are constructed with the bend on the top to refract the light for illumination. The Power Ventilation option added a center vent to the dash as was found on factory air conditioning cars.  Just more outside air circulation.*Tip for removal of your old lens. We have found it easiest to use a dremmel or other type of small cutoff...

This white plastic spacer fits into the back of the right hand inner knob on cars without factory fader or balance. If your inner knob is loose and will not align, you will want to see if this part is in place. 1968-70 AM-FM radios would not utilize this part because they have a balance feature. 1967 AM-FM radios would use this part as they did not have a balance feature. Called a "Sleeve" 1969-70 Cougar and Mustang AM radios use this sleeve. Also found on various 1970-76 Ford and Mercury cars...

Rare option that makes your inner right hand radio knob work as fader. Very limited supply, guaranteed to work. New Old Stock switch. Ford part number C7AZ-18972-A and C7AA-18972-A on the wiring tag. NOS

Rare option that makes your inner right hand radio knob work as fader. Very limited supply, guaranteed to work.

White reproduction fan for the Thermactor Smog Pump.

Replaces Ford part # C9ZZ-8146-C. This is an excellent reproduction made from the original Ford tooling and features the original Ford logo and part number. This is for the 20" radiator. Click on images to enlarge Customer feedback found at mercurycougar.net: Boy service is just not the same as the "good old"? days. I ordered a half a trunk load of parts and pieces from West Coast Classic Cougar and about 2 hours later got a phone call informing me that the order was picked and shipped. What...

Replaces Ford part # C9OZ-8146-A. This is a quality, made in America reproduction made from the original Ford tooling. This is for the 24" radiator found on Mustang, Torino and Cougar with AC or for Cougars that need extra cooling capabilities beyond what the 20" radiator / shroud can deliver. NOTE: This shroud will fit on the 67, but will only work on small block Cougars that have been retrofitted with a 1968 - 1969 24" small block radiator and mounts. For some helpful tips on upgrading your...

Replaces Ford part # C8ZZ-8146-A. This is a good reproduction made from the original Ford tooling but does not have the original part number or FoMoCo lettering. Has a smooth texture (unlike original) but it is made from a more durable plastic material. This is for the 24" radiator only. For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

Fan shroud installation kit for 67 - 71 Cougars and Mustangs. Will fit 1971 Cobra Jet shrouds.

Fan spacer, measuring 1-1/2 inches. Application includes 1970 Mercury Cougar and Ford Mustang with 351 engines and standard cooling. Reference number YA-21, cross reference to C8OE-8546-A spacer. This is a service replacement design spacer, which came out about 1970. Fits all the same.Ford Motorcraft part # D0AE-8546-B, Ford engineering # D0AZ-8546-B.

Fan spacer, measuring 1-1/2 inches. Application includes 1969 Mercury Cougar and Ford Mustang with 351-2V engines and standard cooling. Reference number YA-21, cross reference to D0AE-8546-B spacer.Ford part # C8OE-8546-A, Ford engineering # C5DZ-8546-B.

Fan spacer measuring 1-1/4 inches. Application includes 1969 Mercury Cougar and Ford Mustang with Boss 302 or 428 Super Cobra Jet engines. Additionally it was likely used on 1971 cars with 351-2V engines and standard cooling. Reference number YA-20, cross reference to D1OA-8546-AA spacer.Ford part # C8YE-8546-A, Ford engineering number C8YZ-8546-A.

Fan spacer, measuring 2-1/4 inches or sometimes mentioned as 2-8/32". Application includes 1970 Mercury Cougar and Ford Mustang with Boss 302 engines, or 351 engines with extra cooling or air conditioning. Reference number YA-31.Ford part # D0AE-8546-A, Ford engineering # D0AZ-8546-A.

Fan spacer, measuring 2-5/8 inches, sometimes mentioned as 2.62". Reference number YA-75.Ford part # C8AE-8546-F, Ford engineering # C4AZ-8546-G.

Fan spacer, measuring 2-7/16 inches, sometimes mentioned as 2.44". Application includes 1971 Mercury Cougar and Ford Mustang with 351 engines and air conditioning. Reference number YA-74.Ford part # C8AE-8546-E, Ford engineering # C4AZ-8546-F.

Fan spacer, measuring 2-9/16 inches or sometimes mentioned as 2.95". Application includes 1968 Mercury Cougar and Ford Mustang with 289/302 engines and air conditioning. Additionally listed as 1969 Boss 302. Reference number YA-27, same as part # D2AE-8546-A.Ford part # C8ZE-8546-D, Ford engineering # C8ZZ-8546-B.

Reproduction radiator fan spacer for fixed or flex fans. Can be used on 1967-73 Mercury Cougar and 1964-73 Fords and Ford Mustangs. Ideally the various length spacers were used to place the fans half way into the fan shrouds for optimal cooling. Original Ford part number C4AZ-8546-A.