1969 Ford Mustang

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

Ford part #: C9ZZ-9A758-A. All V-8 engines. The plastic portion that is designed to cover the cable at its furthest point by the carburetor will be broken. This is how the vast majority are for 1969, very rare to find a perfect one. Notice there are two versions for 1969, one has a plastic connector that mounts to the firewall and the other version is metal.

Replaces Ford part #: C9ZZ-9A758-A.  This updated Throttle cable is decent quality. Thicker stranded cable, correct dimensions with a good fit. A basic replacement cable. Approximately 23" in length.

Reproduction Accelerator Pedal for the 1969 and 1970 Mercury Cougar

Black moulded plastic pedal pad for all 1969 and 1970 Mercury Cougars regardless of engine or transmissions. Used pads with various amounts of wear on the surface. Stainless surround trim available too - Part number C9OZ-9735-A.

Reproduction Concours Correct throttle return spring.Replaces Ford Part # : C9ZZ-9737-A

Concours Throttle Return Spring for the 390 / 428CJ / 428SCJ Manufactured after 4-9-69

This correctly formed carburetor throttle solenoid idle bracket for the 1970 428CJ engines on any Mercury Cougar or Ford Mustang. This is a nice reproduction item.Replaces part # D0ZZ-9B550-A.

This is an accurate reproduction of the tie down notice decal that was placed on the rear license plate frame. This was to remind dealers to remove the tie down plates that were used to secure the cars to the transport trains / trucks on their way from the factory to the dealers. Ford wanted to recycle these plates to save money, but dealers often didn't feel it was worth their time to remove the plates. Thus, many cars still have them. Check yours out! ...

Inner tie rod end for 1967 - 1969 Mercury Cougar and Ford Mustang with or without power steering and either drum or power disc brakes. Quality reproduction part. Sold individually, two needed per car. Replaces Ford Part #: C7ZZ-3A131-A

Outer tie rod end for 1967 – 1969 Mercury Cougar and Ford Mustang with either power steering or manual steering and with drum or disk brakes. Quality reproduction part. Sold individually, two needed per car. Made in the USA. Replaces Ford Part #: C7ZZ-3A130-A. *Note – Excludes 1969 Boss 302 Eliminator and Mustang. *Note – Use 1970-73 arm for vehicles with the 'Granada' disc brake conversions.

Used timing chain cover for any 289 / 302 / 351W engine from 1968-70 Mercury Cougar and Ford Mustang or most any 1968 Ford with 289 or 302. Cast aluminum construction without excessive damage. Installation bolt kits also available. Sometime during the 1969 model year, the timing chain cover number changed to C9OE-6059-A. So either one will interchange. Replaces Ford part number C8AE-6059-A.

Used timing chain cover from a  351W or Windsor engine from 1969-70 Mercury Cougar and Ford Mustang or most any 1969-70 Ford with 351W. Honestly, we have found that most of the 1969 production year came with the C8AE-6059-A timing cover. Cast aluminum construction without excessive damage. Installation bolt kits also available. The C8AE-6059-A timing cover can be used on 1970 302 and 351W engines, as long as you use the 1970 timing pointer. The 1970 timing pointers use alternate...

Used timing chain cover for any 390 or 428CJ engine from 1968-70 Mercury Cougar and Ford Mustang or most any 1968-70 Ford with 390 or 428 cubic inch engines. Cast aluminum construction without excessive damage. Installation bolt kits also avialable. Ford casting number C8AE-6059-B. *Note - Is not technically compatible with 1967 or earlier 390 engines.

Set of 6 bolts for installing an OEM Ford timing cover marked C8AE-6059-A, which originally came on all 1969-70 Mercury Cougars with 289 / 302/ 351W engines or 1968-70 Fords including Mustang with 289 / 302/ 351W engines. 4 short and 2 long bolt in this kit.*Note this kit is not applicable to the early designed Ford timing cover, see related items for other kit.

Set of 10 bolts for installing an OEM Ford timing cover marked C8AE-6059-B, which originally came on all 1968-70 Mercury Cougars with 390 / 428CJ / 427-4V engines or 1968-70 Fords including Mustang with 352 / 390 / 428CJ engines. *Note this kit is not applicable to the 1963-67 designed Ford FE timing cover, see related items for other kit.

Stamped Steel Pointer Mounts to Timing Chain Cover. Black Zinc-Plated. Includes Mounting Screw. Correct for 289, 302 and 351W Mercury Cougar or Ford anything including Mustang. We know the other vendors claim this part to fit 1967-73, but it doesn't. Works with 1968-69 Ford timing covers and with 1968-69 Ford 3 bolt harmonic balancers. Starting in 1970, Ford V-8 engines for Mustang and Cougar had timing pointers installed on the passenger side of the engine, and used harmonic balancers with 4...

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1968-69 Mercury Cougar and Ford Mustang 289, 302, and 351W Mercury Cougar or Ford anything including Mustang. We know the other vendors claim this part to fit 1967-73, but it doesn't. Works with 1968-69 Ford timing covers and with 1968-69 Ford 3 bolt harmonic balancers. Starting in 1970, Ford V-8 engines for Mustang and Cougar had timing pointers installed on the passenger side of the engine, and a companion harmonic balancer with...

Concourse Correct Timing Pointer for the 1968 - 1970 390, 390GT or 428CJ. Technically, by design, this is a copy of a 1969-70 390/428CJ timing pointer. It will also work for 1968, since the harmonic balancers and timing covers are the same.Replaces Part # C9AZ-6023-A.* Note - not correct for 428 Super Cobra Jet, see related item.

New Old Stock Timing Pointer for the 1968 - 1970 390, 390GT or 428CJ. Fits all 1969-70 Mercury Cougar, Ford, and Mustang, with 390/428CJ. It will also work for 1968, since the harmonic balancers and timing covers are the same. Replaces Part # C9AZ-6023-A. * Note - not correct for 428 Super Cobra Jet, see related item.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1969-70 Mercury Cougar and Ford Mustang with 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Ford part number C9AZ-6023-A. * Note 428 Super Cobra Jet uses a different pointer, see related.

Stamped Steel Pointer Mounts to Timing Chain Cover. Correct for 1969-70 Mercury Cougar and Ford Mustang with 390-4V, or 428CJ engines. Mounts with existing timing cover bolts. Replaces Ford part C9AZ-6023-A.* Note 428 Super Cobra Jet uses a different pointer, see related.

Concourse Correct Timing Pointer for any 428 Super Cobra Jet Replaces Part Number C9OZ-6023-A.

Reproduction tips and screws for your convertible top welt. It's the strip that goes across the top back side of the convertible top. These are the decorative tips that go on each end of the welt.Each kit includes two tips and two screws.

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1969 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

No more screw drivers or pliers to get that 1969 unique mirror nut loose! Works for the chrome and sport driver side remote mirror for 1969. Keep in mind that these tools are designed to fit the original mirror nut, we've found that they don't fit well on the reproductions. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a passenger side mirror or using Riv-Nuts? Got a mirror lens that flops around in your Sport Mirror...

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

Sold individually Zinc (dark silver)

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.

Nice quality hardware for attaching the shift rods to the bottom of the shifter mechanism. Won't work with the 1970-73 Hurst shifters, but does work with all of the others. Including 3 speeds, sorry, sold in packages of 3 though. Check out our video on rebuilding your shifter below: ...

Reproduction passenger side (left hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

This is a reproduction 3 piece non assembled torque box for the driver side on the 69 - 70 Cougar or Mustang Coupe. The benefit of getting a non assembled torque box is that you'll find installation much easier as compared to the pre-assembled boxes.  Included are inner and outer panels and gusset. Passenger side non-assembled torque boxes are not available.

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Reproduction torque box gusset for your 67 - 70 Cougar or Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box for extra strength. Sold as a pair.

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.

Rebuilt C4 24 spline torque converter for the 1967 - 68 Mercury Cougar or 1966 - 69 Ford Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. Ford part number C6AZ-7902-M. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of...

Rebuilt C6 FE Engine torque converter for the 1967 - 70 Mercury Cougar and 1966-70 Ford and Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. 1966-70 Ford FE engines include: 352, 360, 390, 427, 428, etc. Ford part number C8OZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad...

Rebuilt FMX torque converter for the 1969 - 73 Cougar or Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core.Ford part number C9ZZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of experience do a very thorough rebuild that is...

NOS Autolite 4300 training handbook. Filled with details pertaining to operation, adjustments, overhaul and servicing of the Autolite 4300 carburetor which was used starting in 1967.  Volume 67 S2 L2, 9503.1, 9503.2

Used Transition cover for the 68 - 69 Cougar or Mustang tilt steering column. This cover bolts to the outer cover tube.

This kit is an easy way to covert your 289 / 302 / 351W engine from a C4 or C6 transmission to an Automatic Overdrive Transmission.Kit includes: Cross memberTrans Mount InsulatorSlip YokeKick Down CableFlex Plate AOD Shift LinkageThis is just the kit, and does not include the full transmission! NOTE: This item is shipped from our supplier direct to you, so expect 1-2 weeks for shipping. ...

Core C6 transmission for a 1969 Mercury Cougar or Ford Mustang. Tag number PGA-Y or PGA-AE. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar S code with 390IP or 390-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.