Interior

Single black Phillips oval headed screw for attaching the face pads onto 1967 Mercury Standard Cougars (non-XR7 models). Sold individually, we also sell these screws under SKU 100022599 in sets of 13 (better value). *Note - This screw is glossy black in color.

These right and left bezels would be considered grade A cores with no cracks or chips. Often there is a missing mounting stud or two on the backside but nothing that shows. The cluster is complete and all the gauges work. If you would prefer a clock over a dummy plate we can upgrade you at no charge but the clock will not work and often will be missing the tiny knob. If you let us know what mileage you would like the odometer to read let us know and we will try and accommodate. ...

Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent.

Good used core plastic bezel that has had one or more cracks repaired. Finish will be poor or non existent.Ford part number: C7WF-10838

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is the very best we can offer. No cracks in the plastic holster, good color and no fraying on the webbing, good chrome on the male buckle and it may even have the date code tag still in place. We will try to obtain the correct date code...

Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models. This is a fully functional retractor that will have a small crack in the plastic "holster" and may show very slight pitting on chrome. Driver quality, ready to plug and play. NOTE: Front retractors are same for left and right, and are good for...

NOS Standard seat belt retractor including bolts and a huge 44" x 33 1/2" Ford seat belt diagram in FoMoCo box and never installed on a car. Standard belts can be identified in 1967 by the plastic lift up female buckle. Deluxe belts are identified by the metal female buckle that are released by a center button. All xr7 models had deluxe belts in 67, deluxe was optional in the standard models.  NOTE: Front retractors are same for left and right. Check out our video "All about...

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 16 individual pads in a package.

Fixed steering column from a 1967 Mercury Cougar. Reasonably rust free column that ships as shown in picture. Often we will leave the turn signal switch in place, but you should count on it being non functional. This steering column will fit a Mustang, but you must change steering boxes. Most 1967 Mustangs came with the steering box with the long spear. Upper and lower mounting brackets, and rag joints are available, but sold separately.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This is my absolute favorite Cougar - Mustang - Shelby option of all time! In fact, as a rather tall person that is not as slim as I once was, I do not really enjoy driving a Mustang or Cougar that does not have this option. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side...

This is a reproduction steering wheel for a 1967 Mustang with Deluxe interior. It makes a nice substitution for the 1967 Mercury Cougar wheel and since the 1967 Mustang used the same steering columns (both fixed and adjustable) you are guaranteed a factory correct fit with no issues making your horn or turn signal cancellation work properly. This steering wheel is being offered without a horn center / pad. You can use your original Cougar hub, which fits perfectly without modification. If you...

This reproduction steering wheel is a replica of the wood rimmed steering wheel originally equipped on 1967 Shelby GT350's and GT500's. It has a beautifully finished real solid wood rim with proper finger indents and a distinctive black band around the back surface just like the originals. The 3 spoke design is brushed stainless steel with 4 chamfered holes per spoke, and unique black rubber finger guards. The main hub is CNC machined aluminum with a satin finish. Each wheel is equipped with...

Brand new WCCC exclusive! These 1967-only steering wheel center emblems have been needed for some time. Most originals are faded, scratched, and often warped or broken. These new ones fit perfectly in your original center pad and look great. Watch our video below to see how to replace your old emblem and trim ring with our new ones. ...

There are three of these rubber, glue on pads attached to the chrome horn center of every 1967 Cougar. The colored pads usually need to be repainted and we cannot guarantee to have all colors in stock at all times. These pads are sold individually, please select the desired color and we will try to accommodate you. Check out the very first Cougar in our video below! ...

For the purists out there we have a very limited amount of used moon crater visors that have no impressions, seam separation and minimal rust on the clips if any.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually.

Reproduction Moon Crater Sun Visor for the 1967 and 1968 Mercury Cougar / Ford Mustang. Visors are fully padded and covered with the correct textured moon skin to match the headliner. Sold as a Pair. Nugget Gold is not available in Moon Skin Crater, it is only available in a smooth vinyl.

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design. Two different sized brackets used, this is the larger one that is 1-3/4 inches wide. The bracket that goes in the corner above the switch panel is 3/32" less. It was obvious what the original intent was on this design in that a tab on the L bracket was supposed to extend...

This often times missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the smaller design. Two different sized brackets used, this is the smaller one that is 1-21/32 inches wide. This bracket goes in the corner above the switch panel. The larger bracket is 1-3/4" or 3/32" wider. It was obvious what the original intent was on this design in that a tab on the L...

Reproduction set of 5 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design of the two and by far the superior. Replaces item # 31908Through 67-68, there were four different style brackets, you can see all four by following this link. ...

This often times missing bracket was attached to the back of your 67 - 68 Standard model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. This is the more common design.Through 67-68, there were four different style brackets, you can see all four by following this link. ...

Reproduction set of 5 XR7 passenger side dash bezel clips. This often missing bracket was attached to the back of your 67 - 68 XR7 model passenger side plastic bezel via plastic studs that easily break off from over tightening the screw. Our improved design is better than the original in that the tab extends into the rectangular recess in the dash bezel which anchors in MUCH more securely. Replaces item # 31907Through 67-68, there were four different style brackets, you can see all four...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang, and most 1965-69 Ford and Mercury full sized cars such as Galaxie, Monterey, Parklane, Montclair, etc.Fits 67 CougarFits 68 CougarFits 65 Mustang Fits 66 MustangFits 67 MustangFits 68 Mustang

Sold individually, three of these are mounted to your 1967 steering wheel. Comes with two screws as shown. Also sold in a set of 3. Check out the very first Cougar in our video below! ...

Sold in a set of 3, these are mounted to your 1967 steering wheel. Comes with two screws as shown. Also sold individually. Check out the very first Cougar in our video below! ...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. The relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash and does...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This turn signal switch for the 1967 Cougar equipped with the tilt / tilt away steering column is made using the original tooling acquired from the original manufacture of this part that Ford purchased these switches from when they were originally installed new in the Cougar. If you have replaced your sequential unit in the trunk with one of our new solid state sequential...

Good used original working tachometer. We will accept your core even if the face is faded or scratched. Please include a copy of your invoice when sending a core.Check out the video below on our new gauge tester: ...

Three wire tachometer for 67 - 68 Cougar. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the tachometer goes bad, the engine shuts OFF. It also means that you must either replace it with another series type tachometer with 35+ year old circuitry or install a jumper wire to bypass the tach. It also means that you need a special adapter to use your factory tach with an MSD ignition box. Our three wire tachs are independent...

Mini Tachometer that fits in the small center clock opening. This easy to install three wire tachometer looks OEM but as you probably know, Mercury never offered an in dash tachometer from the factory. Just remove your current clock or dummy plate and this unit installs from the backside in its place. If you are returning a core dummy plate for credit it must have good cosmetic appearance. When you send your core for credit, please be sure to include a copy of your sales receipt. Check out the...

These differ from 68-69 in that there is no starter safety switch embedded in them. This is a used part, tested, lubed, and working. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting.

C7WB-13713-A New old stock XR-7 dash toggle switch for the "Panel" light on the 1967-68 Cougar. This switch has the black plug, and it will work for the "Courtesy" light switch too, those are typically have red plugs though.

Used set of 4 toggle switches for the 67 XR7 Cougar dash panel. Included are the toggles for the driver side map light, panel light, passenger map light and courtesy lights. Switches have been tested and may or may not have the tips in place, but we do offer a reproduction set of toggle tips.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Ignition bezel adapter tool removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included.  ...

Adapter tool for installing and removing remote door mirror bezels on 1967-68, and 1970-73 Mercury Cougar and Ford Mustang. Should be coupled with the basic tool (item 32368) A 5/32" Allen wrench is needed to attach tools together. Allen wrench not included. *Note - Excludes 1969 remote mirror bezels. ...

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

This is a bezel nut tool used to remove the toggle switch bezel nuts on 67 - 68 & 71 - 73 XR7 Mercury Cougars. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This is a MUST HAVE if you are replacing a toggle switch or taking apart your dash, we use this tool in our shop all the time and love it!

This two piece painted trim / moulding set helps to secure the package tray in place at the bottom of the rear window. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

Replaces Ford part #: C7ZZ-3656-A, concours correct for all 1967 Mustang's and Cougar's. This beveled ornamental plastic ring is for your 1967 steering wheel hub. The inner diameter is 3 3/4" and the outer diameter is 4 3/8" and it stands 5/16" tall. This ring fits many FoMoCo products but keep in mind there is another version that is completely flat like a washer. We suggest you use soapy water and heat your hub before trying to slip this on. It also helps if you go around the perimeter and...

This reproduction is pathetic... It's made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. No returns on this product, we suggest no mat is a better alternative than this poor quality reproduction. It's that bad... Please look at our premium quality trunk...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern by Auto Custom Carpets. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit...

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video below: ...

1968 Mercury Cougar / Ford Mustang complete ashtray assembly with lighter.The manufacturer claims that it will fit a 1967, but this one is about 1/4 inch shorter over all compared to the 1967 unit. *NOTE* Will only fit the 1968 dashes.Click on images to enlarge. ...

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

Used vacuum release valve for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. This vacuum solenoid releases the steering column for the swing away function. These vacuum tilt solenoids are tested and guaranteed to work. Bench testing the 1967-69 tilt away release solenoid: Verify that there is continuity between the two electrical spade connectors. No continuity means the the windings in solenoid windings are bad. This is a bad solenoid. Next, put vacuum to...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

Reproduction driver side (left hand) vent / wing window handle for the Mercury Cougar or Ford Mustang.