Interior

Original good used part with no cracks, but may be brittle from age. These really are getting hard to find in mint condition. For the money, the reproductions are every bit as good as the originals. They are also available in red and yellow.Replaces Ford part number C4VY-10B870-A.

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used locking pawl for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. This pawl is released and via the vacuum motor when the door is opened and the ignition is in the off position. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used grade A lower center console pad for the 1967 Standard Automatic Transmission. We rarely have these in stock so the chances of getting the color you desire is slim. We have several Grade B's with cigarette burns, cracks and the like for substantially less money.

Used grade B lower center console pad for the 1967 Standard Automatic Transmission. We rarely have these in stock so the chances of getting the color you desire is slim. 

Good lower pad with no cracks or burns. We have several of these in stock but cannot guarantee we can give you the color you select. Mention in the notes of your order what color you would like and plan on repainting this item even if we can provide your color as there is always some discoloration from age and use.

Good lower Grade B pad with no cracks or burns. We have several of these in stock but cannot guarantee we can give you the color you select. Plan on repainting this item even if we can provide your color as there is always some discoloration from age and use. Grade B will be pulling away from the base and will need glued.

Good used pad with no cuts or burns. Be aware that this is a sample picture, and you will need to specify the color you're looking for. NOTE: Almost always the vinyl will be de-laminating from the foam. This can be fixed with C clamps, wood strips for equalizing pressure and contact cement. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in...

Optional trunk lamp. Includes mercury switch that mounts on inside trunk lip, round plastic wire protector bezel, mounting screw and wiring pigtail. Ready to install working part, #631 bulbs available. Guaranteed to work, no cuts or splices.Can be added to any 1967 - 1968 Cougar and may be able to be added to the 67 - 68 Mustangs, but some Mustang forums indicate the Mustang lamp had a different wire length than the Cougar lamp and this version is stamped with the correct part number for the...

This will really help you understand how your column works! Covers operation, tests and adjustments. All Mustang / Cougar tilt columns were tilt-away in 1967 - 1969. This manual is free for the asking when you purchase a tilt column from us. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most...

Map light bezel for overhead roof consoles on both 1967-68 Mercury Cougar XR7 and Ford Mustang. These are a great reproduction at a great price. These were always pitted and before the reproductions came out three years ago a very nice used pair sold for about $100. To date we have sold more than 300 pairs and have had great feedback! Sold in pairs. Bezels only. Sometimes called a 'door' Ford part number C7ZZ-13788-A. *Customer Comments* Hello. I just bought my first 1967 Cougar XR7 in about...

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In 1967 they used a floral design which was the same left or right. In 1968 they were embossed with the iconic walking cat design. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In 1967 they used a floral design which was the same left or right. In 1968 they were embossed with the iconic walking cat design. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In 1967 they used a floral design which was the same left or right. In 1968 they were embossed with the iconic walking cat design. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In 1967 they used a floral design which was the same left or right. In 1968 they were embossed with the iconic walking cat design. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.  

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In 1967 they used a floral design which was the same left or right. In 1968 they were embossed with the iconic walking cat design. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In 1967 they used a floral design which was the same left or right. In 1968 they were embossed with the iconic walking cat design. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.

This material is sold as a pair and are used to re-cover your XR7 door map pockets. In 1967 they used a floral design which was the same left or right. In 1968 they were embossed with the iconic walking cat design. NOTE: Map pockets are not included, this is simply a vinyl repair kit to re-cover your existing pockets.

Good used metal portion of the door panel. If yours is bent or you're doing custom made door panels, you will need these.

Good used metal portion of the door panel. If yours is bent or you're doing custom made door panels, you will need these.

Metal support piece for the drivers side dash bezel. This piece mounts on top of the dash bezel and adds strength to where it mounts to the dash. It will require 5 screws to attach the dash. Check out our video on dash removal and restoration: ...

Metal support piece for the passenger side xr7 dash bezel used on the LATE 1968 Cougar, much better than the multiple piece brackets found on the majority of 67 and 68 xr7 models. This piece mounts on top of the dash bezel and adds strength to where it mounts to the dash. It will require the use of epoxy or tiny shallow depth screws to adhere it to the plastic bezel. Through 67-68, there were four different style brackets, you can see all four by following this link. Check out our video on...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Grade A condition - driver side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1967 Mercury Cougar, driver side only. Grade A condition, will have supple vinyl without damage. minor or no de-lamination. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best results you should plan on spraying it with your specific...

Grade B condition - driver side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1967 Mercury Cougar, driver side only. Grade B condition, will some foam de-lamination on the back. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best results you should plan on spraying it with your specific interior color.Replaces Ford...

Grade A condition - passenger side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1967 Mercury Cougar, passenger side only. Grade A condition, will have supple vinyl without damage. minor or no de-lamination. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best results you should plan on spraying it with your specific...

Grade B condition - passenger side 'A' pillar pad, clips into the 'A' pillar post between the windshield and the door glass. Fits 1967 Mercury Cougar, passenger side only. Grade B condition, will some foam de-lamination on the back. Attaching clips sold separately. Please include desired color in the 'notes' or 'comments' section of your order. We can often supply your color, limited to available stock. For best results you should plan on spraying it with your specific interior color.Replaces...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

No cracks or pits, very nice condition. Used only on the 1967 Cougar standard console with automatic transmission, but can easily be cut to accept the four speed insert.

Minor pitting, good condition. Used only on the 1967 Cougar standard console with automatic but can easily be cut to accept the four speed insert. Chrome will be very slightly discolored on grade B.

You can trim the automatic version of this part and use it in conjunction with the four speed insert.

This two piece painted trim set helps to secure the dash pad in place at the bottom of the windshield. 1968 Mercury Cougar used a slightly shorter trim set due to the padded windshield pillar pads. The 1967 will work fine, all of holes line up the same. These 1967 trim pieces also have a smooth painted surface, 1968 Cougar pieces have a slightly textured painted finish. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. Will...

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

Steel plate for mounting the door pull or grab handle on 1967-68 Mercury Cougar XR7. Right and left is dependent upon which way the nylon inserts are installed. Comes complete as shown with nylon inserts for attaching the door pulls. The screws with 1/2 inch flat head for mounting this plate to the doors are also a available (three required).

Ninety degree bracket needed to mount the starter safety switch to the column tube in 1967.

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

We rarely have extras of these in stock but we like to show these items so you know what you are looking for or you can use it as a visual and fabricate your own kit. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice.Also available as a reproduction mounting kit. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them. ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Fits 1967 Standard and XR7 Cougars or most Ford and Mercury with inside rear view mirrors. Also used on the 1967 xr7 hash marks located on the rocker.

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber, and the rubber to the window channel. Non hardening and stays pliable, 1/10th of a gallon. You will need no less than one tube per window as you will need to put a bead inside the U channel of the rubber weatherstrip as well as a generous bead on the car. This product additionally was used for securing...