Interior

Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.

Knob is exact replacement, element is a generic replacement. Socket and element are manufactured by the same company to insure fit. Exact replacement for 1967-68 dash or 1969-70 under dash lighter and lighter socket. Replaces Ford part # C7ZZ-15052 and C6ZZ-15055-B.*Note - Retainer should have a ground lug on it in order to work with 1969 console cigar or cigarette lighters.

This unique little clip looks a lot like the more common door panel clip but on close inspection you will find it is different. Whereas there are slots for three of these per side, only two per side were installed at the factory.Replaces Ford part number 352775-S100.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

This clip attaches the rear edge of the Xr7 overhead console to the support bracket. In 1968 the more common door panel clip was used for this application. The door panel clip can also be used for your 1967 model, we recommend the used clip over the new one.

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Door panel clips for the 1967 Standard or XR7. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Fits 1967 and 1968 Standard or XR7

Fits 1967 and 1968 Standard or XR7. This kit is nothing more than common door panel clips instead of the correct, unique 1967 A pillar pad clips or 68 A pillar pad clips . These can be made to 'work', but we highly recommend ordering the correct used clips.For the Correct 1967 A pillar pad clips, click here.For the Correct 1968 A pillar pad clips, click here. ...

This unit has had the original movement replaced with a quartz movement. It has been meticulously rebuilt by the best in the business and features a new, crystal clear lens. $150 credit when you return your clean rebuildable core with a copy of your invoice. Quartz movement clocks have second hands that click around, original clocks had a constant sweep of the second hand. Check out the video below on our new gauge tester: ...

This is a NOS clock. The face is brilliant, it has never been mounted and is guaranteed to work good. It does have a tiny crack that is mostly hidden by the center knob which is very common for these original lenses.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

C7WY-15000-A 1967 - 1968 Standard Cougar body code 65A or 65C, found optionally in the small center pod of the instrument cluster. Used clocks generally do not work after 40 years and unfortunately these do not include the clock knob as folks often do not put them back on after removing them from the cluster. These are considered cores. We also offer rebuilt clocks with modern quartz movements and those will include the knob. Check out the videos below on our new gauge tester and the "Cougar...

Used clock for the center console equipped Mercury Cougar XR7. Most used clocks typically do not work after 40+ years and you can also expect that the lens will have some cracks. However, we offer a nice reproduction lens or restored clocks with a modern quartz movement or NOS movement.Ford part # C7WY-15000-B.Check out the video below on our new gauge tester: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we...

[No Description Provided]

Prepare to be disappointed... This is a reproduction 1967 - 1968 Ford Mustang clock knob and set screw (replaces Ford part # C7ZZ-15032-A) that can be cut down to work on your 67-68 standard Mercury Cougar (barely). The pictures below will guide you on this "adequate at best" solution for those of you missing this hard to find knob and set screw.Click on images to enlarge. The above picture is a good used original Cougar knob mounted on a 68 clock.  We do not have these original Cougar...

This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.

Sold as pair, exact copy. These also double to keep your windlace firmly in place.

One year only part not found on any other car except Cougar and Mustang with tilt. If you would like to run a 1968 or newer steering wheel on your 1967 then you need to exchange this cover with the version found on the 1967 Thunderbird which has no lip at the top. We have these in stock and would enthusiastically trade it for the Cougar / Mustang upper cover. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This Thunderbird collar is a good substitute for those wanting to put an after-market or 1968 up steering wheel on their 1967 Cougar / Mustang. We also suggest purchasing this collar when installing our reproduction 1967 Mustang deluxe steering wheel.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction Console Ashtray Bumper for the 1967 Mercury Cougar or Ford Mustang.

Differs from the original lens in that it is all white. The original was painted white on one half and left clear on the other.

Fits 1967 and 1968 Standard or XR7

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull.  We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...

Have you been in a discussion with someone about how many W-code GTEs were made? The real percentage of Cardinal Red convertibles that were made? How many Eliminators were made each year? Now you'll know these things and so much more. This book contain never before published information drawn direct from company records, and over 14,000 statistics. This book includes: Exhaustive charts of paint color-trim combinations Engine-transmission production for each body style Option production rates...

C7WB-13K705-C-AGRADE Left side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13K705-C courtesy lamp assembly left hand side. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Hardest side to find in primo condition most get dinged up from errant seatbelts. This...

Left side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13K705-C courtesy lamp assembly left hand side. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses.Replaces Ford part number C7WB-13K705-C.Fits:1967 Mercury Cougar1968 Mercury Cougar ...

C7WB-13707-C Right side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13707-C courtesy lamp assembly right hand side. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

Right side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13707-C courtesy lamp assembly right hand side. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses.Replaces Ford part number C7WB-13707-C.Fits:1967 Mercury Cougar1968 Mercury Cougar ...

Rechromed Bezel for your door courtesy lights found on all 67-68 Cougars except the 1968 Standard model. These will require some patience with a dremel tool to remove the lenses from your cores and place them in these. Passenger and driver are the same, keep in mind the red lens goes to the back of the bezel. To be eligible for core refund, your cores can only show light pitting. ...

Used pivot cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction headlight knob, retainer & bezel, cigar lighter and ignition switch retainer.

These studs and nuts are used to repair the passenger side mounting studs. The studs need to be drilled out using a 1/4" drill bit. Once done, use a 2 part epoxy and install the stud. Make sure to avoid getting epoxy on the threads where the nut will be installed. Once dry, install the bezel into the dash and use a 3/8 # deep well socket to install the nut. CAUTION: Only tighten finger tight to avoid cracking or breaking the bezel.

Used metal dash support brace for all 1967-68 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 8-1/2 inches long. Viewed in the 1967 Osborn Body Assembly Manual on page 23. Replaces Ford part numbers C7ZB-6504672 or C7ZZ-6504672-A.

This 2 1/4" trim part installs directly above the steering column.

When removing this part resist the temptation to "open it up". Instead walk it off carefully leaving it in its factory position.

This unique to 1967 standard Cougar dash trim set is what outlines the gauge cluster face pad. It is unique to the 1967 standard Cougar as it is held in place by black Phillips Screws. The 1968 trim set is held in by clips. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent.

Used aluminum face pad moulding / trim four piece set for the Mercury Cougar.

This trim part starts to the upper left of the gauge cluster and continues on to the passenger side following the line of the upper padded dash.

Only for use on standard model Cougars with no A/C. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Used dash face pad for the standard Mercury Cougar that is NOT equipped with air conditioning. This unit will be nice and will not have any cracks, but could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find your local autobody supplier. They should be able to mix up a small amount of the exact color you need. This icon means that we're looking to buy...

This set of three woodgrain dash inserts for the Mercury Cougar equipped with A/C are the best of the best of which we can provide you with. These grade "A" inserts retain a rich, original looking finish and have not been subjected to prolonged damaging UV rays. We carefully match these under bright lights to ensure they match color wise. No scratches, dings or other blemishes, and all four toggle switch labels will be in place. Includes a brand new XR-7 emblem to make the dash really pop....

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check out our video on dash removal and restoration: ...