Electrical & Lighting

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. This turn signal switch for the 1967 Cougar equipped with the tilt / tilt away steering column is made using the original tooling acquired from the original manufacture of this part that Ford purchased these switches from when they were originally installed new in the Cougar. If you have replaced your sequential unit in the trunk with one of our new solid state sequential...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. For 1968, the relay under the dash almost always is weak (pulsates dimly instead of distinct blinking) but its sole purpose is to illuminate the directional arrows on the dash...

Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk with one of our new solid state sequential units and are still having problems then the turn signal switch is most likely the culprit as the only other part to the system is the wiring harness itself. Often when your brake lights are not working the turn signal switch is the culprit as the brake lights feed through the turn signal switch. This switch also fits the 1970-1972...

Tested and working used 2 speed windshield wiper switch for any 1971-73 Mercury Cougar and Ford Mustang. Replaces Ford part number D1ZB-17A553.

Tested and working windshield wiper switch for the 1967 Mercury Cougar standard model. Models 65A and 65C, not XR7 models. The 1968 Wiper switch knob is slightly larger than the 1967 version and is detachable. 1967 knobs say 'WIPERS'Ford part number C7WB-17A553-A.

Tested and working windshield wiper switch for the 1968 Mercury Cougar standard model. Models 65A and 65C, not XR7 models. The 1968 Wiper switch knob is slightly larger than the 1967 version and is detachable. Knob sold separately.Ford part number C8WB-17A553-A.

Good chrome shaft, guaranteed to work well. 1967 has a small press on rectangular knob with "wiper" lettering.

Good chrome shaft, guaranteed to work well. 1968 uses a larger knob with an allen set screw to hold it in place. Knob sold separately. Keep your old knob.Ford part number C8WB-17A553-B.

Tested and working emergency / parking or parking brake indicator switch and bracket. Standard switch found on 1967-68 Mercury Cougar XR7 models. Optional on Cougar standard model 65A and 65C, also optional on Ford Mustang. Clamps to the hand parking brake assembly. Ford part number C7ZZ-15A851-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Tested and working emergency or parking brake indicator switch. Foot parking brake switch found on 1971-73 Mercury Cougar and Mustang. This particular switch is also found on various other Ford/Mercury products starting in 1970. Ford part number D0AZ-15A851-A.Includes bolt to attach to emergency foot brake.

Used convertible top switch for any 1971-73 Mercury Cougar Standard Model Convertible - Non-XR7. This is a momentary push switch. Tested and and working used switch.Replaces Ford part number D1WY-15668-A.

Used switch panel with 3 switches for all 1971-73 Mercury XR7  with convertible tops. Inspected and tested switch panel for COURTESY - MAP - TOP. All three switched prove will function and operate. Toggle tips included. Do you have extra, or non working 1971-73 XR7 convertible top switch assemblies? As long as the circuit board part of it isn't damaged we will buy them for $30. Switch assembly must be stamped D1WB-15668-AA on the reverse. *Note - Excludes Non - XR7 model...

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

Advantages of  Pre-Sending Cores:- Ships after we receive your 1967, 1968, 1969, or 1970 Mercury Cougar XR7 tachometer, (Yes, any factory installed Mercury Cougar tachometer from 1967-1970 is acceptable) avoiding unnecessary core charges. Tested and working 6000 RPM tachometer with correct emergency brake indicator light lens and plain green lens. 1969 Mercury Cougar XR7 and Eliminator models only. Ford part number C9WF-17360-A.*Note - Boss 302 Eliminators normally received 8000 RPM...

Tested and working all metal 6000 RPM tachometer with correct Seat Belt and Lights indicator lenses. 1970 Mercury Cougar XR7 and Eliminator models only. Ford part number C9WF-17360-A. There is a second manufacturer (See other listing) of this 1970 tachometer which was manufactured by Faria Instruments. It is identified by having a plastic rear housing and a rest for the needle. It has a part number of C9WF-17360-A2. *Note - Boss 302 Eliminators normally received 8000 RPM tachometers.*Note -...

Good used original working tachometer. We will accept your core even if the face is faded or scratched. Please include a copy of your invoice when sending a core.Check out the video below on our new gauge tester: ...

Tested and working 71 - 72 6000 RPM standard face tachometer with correct brake and oil indicator light windows. Ford part number D1WF-17360-F Shipping and Packaging Tips: Tape something over the face of the tachometer, or put them into a small container to protect the delicate needle. We normally use plastic sandwich containers that protect the face of the tachometer from coming into contact with packing materials or the cardboard box. Please make sure that the tachometers are packed so...

Requires a $50 refundable core charge, send us your dummy plate for a core refund! No, Mercury never offered an in dash tachometer for your 1969 - 1970 Decor or Standard model Cougar... For years people have been "making" 2 wire tachometers from xr7 and Eliminator Cougars work (kind of). This is a brand new three wire tachometer custom made to look and fit like the original would of had they been available in the day.  If you would like to retain the original standard clock we now have a...

Three wire tachometer for 67 - 68 Cougar. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the tachometer goes bad, the engine shuts OFF. It also means that you must either replace it with another series type tachometer with 35+ year old circuitry or install a jumper wire to bypass the tach. It also means that you need a special adapter to use your factory tach with an MSD ignition box. Our three wire tachs are independent...

Requires $65 Core Charge. Return your core to us for a $65 refund! Three wire tachometer for Cougars. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the tachometer goes bad, the engine shuts OFF. It also means that you must either replace it with another series type tachometer with 35+ year old circuitry or install a jumper wire to bypass the tach. It also means that you need a special adapter to use your factory tach with...

Return your core to us for a $65 refund! Three wire tachometer for Cougars. Ford wired their early (pre ‘74) tachometers so that they are part of the ignition circuit. What this means is that if the tachometer goes bad, the engine shuts OFF. It also means that you must either replace it with another series type tachometer with 35+ year old circuitry or install a jumper wire to bypass the tach. It also means that you need a special adapter to use your factory tach with an MSD ignition box. Our...

Good used grade "A" taillight bezel for the 67-68 Mercury Cougar. This grade "A" unit will not have any pits, bends on the ribs and the chrome will have good luster. When you mention it in the comments section, we will try to pick out examples that still have the detail paint in tact. This no excuses bezel will look great on your high quality unrestored driver. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

Good used driver quality grade "B" bezel with no bends, cracks or deep pits. Chrome will have a decent luster (not perfect), but the paint will need to be redone. If you want show quality then the only way you will be happy is to buy our rechromed bezels. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

These never came on a Cougar; these are reproduction 1967 Shelby tail light lens bezels. The reason we list them is that over the years many of our customers have been cutting out their vertical ribs on the 1967-68 Cougar tail light bezels to completely expose the tail lens.  These Shelby bezels offer a direct replacement clean restomod look without all the hassle of cutting up your valuable Cougar parts. As the close up will show there are slight machining marks so you may want to polish...

Sold individually, right is the same as left. Needs no repaint in the reflective area and will actually be in much better condition than what is pictured. Seals will need replaced as they are original. Comes with original mounting studs. Great for Shelby or Eleanor clones. Why buy $100 ABS plastic reproductions when you can have original FoMoCo? *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned...

The only difference between grade "A" and grade "B" on this part is the reflective finish on this grade "B" part needs to be redone. There is a spray paint specifically for this application sold by Krylon and others. The pair you get will actually look much better than what is pictured here. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Good used socket ready to plug into your 67-68 tail harness and snap into your taillight housing. Also used on 1967 Shelby Mustang. Sold individually, six required per car.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Sold as a pair. New to the market as of 2009. Take a look at our many pictures below of these bezels installed with original backing plates and lenses. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check...

Used grade "A" taillight wiring harness for the Mercury Cougar. No cuts or splices, perfect plugs with no visible corrosion.  This harness is for the Late 1971 (after 5/15/1971) through 1972.  There were 2 other harnesses for early 1971 (D1WY-14405-B before 2/1/71 and D1WY-14405-D from 2/1/71 - 5/15/71).  If you are in need of one of these early harnesses, please contact us so we can discuss what you need.Ford part # D2WY-14405-A.*NOTE* Need help diagnosing a Cougar...

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13441-AA ...

This is a restored 1973 driver side taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.

This is a restored taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. Ford Part Number: D1WB-13440-AA ...

This is a restored 1973 passenger side taillight housing assembled in-house. Complete assembly with new sockets and repaired pigtails in place. Reflective background has been re-painted silver. No major cracks or chips, every unit is thoroughly tested. NOTE: 71-72 housings will not work on the 73, and vice versa. While you're at it, you can grab some new gaskets here. ...

Complete assembly with good sockets and pigtails in place. No cracks or chips, every unit is thoroughly tested.

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a red 4 pin plug, that is designated D-3 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 4 pin plug, that is designated D-4 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a white 4 pin plug, that is designated D-4 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 2 pin plug, that is designated D41 in the wiring diagram. This plug plugs into the sequential turn signal relay in the trunk. We are offering all of the various plugs for repairs.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

1967 and 1968 Mercury Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 4 pin plug, that is designated J77 in the wiring diagram. This plug plugs into the sequential turn signal motor in the trunk. We are offering all of the various plugs for repairs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s...

67 - 68 Cougar tail light wiring harness repair plug end. We clip these with a generous amount of wiring (6 plus inches) that allows you the car owner to repair your own tail light wiring harnesses. This is a black 5 pin plug, that is designated P79 in the wiring diagram. This plug plugs into the emergency warning relay flasher in the trunk. We are offering all of the various plugs for repairs.Good for both STD and XR7 models*NOTE* Need help diagnosing a Cougar turn signal problem? Victor...

This oddball sequential unit was only used from 2/1/1971 to 5/15/1971 and will be of no interest except for to select few. The differentiating factor is the hard plastic connectors. We can supply a reproduction of this unit but it requires that you send your old unit to to us so we can reuse the plugs. Ford part # D1WY-13A366-C. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the center position of your taillight section.

Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the inner position of your taillight section.

Driver side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the outer position of your taillight section.

Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the center position of your taillight section.

Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the inner position of your taillight section.

Passenger side taillight socket with wiring pigtail for the 69 - 70 Mercury Cougar. This is the socket that sits in the outer position of your taillight section.