Switches / Relays / Circuit Breakers

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are spotty at best. We recommend our good used units which you can get right here.

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are what other vendors offer, but they pretty poor quality and spotty at best. We highly recommend that you buy our good used units which you can get right here.

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are spotty at best.Replaces Ford Part #: D1ZZ-17553 or D1ZZ-17553-A

New Old Stock NOS windshield wiper switch for any 1970 Cougar or Mustang. Marked DOZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than the 1969 version.

Good used windshield wiper switch for any 1969 Cougar or Mustang. Marked C9ZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than this 1969 version.

Good used windshield wiper switch for any 1970 Cougar or Mustang. Marked DOZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than the 1969 version.

Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.

Dash color painted steel bezel that houses the courtesy lights on all 1969-70 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL ACCY. Sold pit free, often times we can select your desired color, but plan on detailing them if your undergoing a restoration. Mention your color in the comments section of your order. Replaces Ford part number C9WB-10964.

Dash color painted steel bezel that houses the courtesy lights on all 1969-70 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL ACCY. Sold pit free, often times we can select your desired color, but plan on detailing them if your undergoing a restoration.Replaces Ford part number C9WB-10964. During assembly of your switches, note that the pins need to be on top. Switches and wiring harnesses sold individually. ...

Dash color painted steel bezel that houses the courtesy switches with DEFOG on all 1970 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL DEFOG. May have some small pits, depending upon stock on hand. Plan on detailing them with your interior color for best results.Replaces Ford part number D0WB-10964-B. During assembly of your switches, note that the pins need to be on top. Switches and wiring harnesses sold individually. ...

Dash color painted steel bezel that houses the courtesy switches with convertible top on all 1970 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL TOP. May have some small pits, depending upon stock on hand. Plan on detailing them with your interior color for best results.Replaces Ford part number D0WB-10964-A. During assembly of your switches, note that the pins need to be on top. Switches and wiring harnesses sold individually. ...

Used bezel for the driver side power seat switch on the 71 - 73 Cougar or Mustang. Ford part number D1ZB-14A706-AA This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

This die cast bezel with a brushed finish was used from 1969 to the first part of 1970. This is a clean example with no pits or obvious scratches. The engineering number found on the back is C8AB-14505-B.

Poor condition with scratches and pitting as shown. This die cast bezel with a brushed finish was used from 1969 to the first part of 1970. The engineering number found on the back is C8AB-14505-B.

Good used bezel with no obvious scratches or pits. This bezel was used on the passenger door and both sides of the back seat in 1969 and on some earlier 1970 Cougars. The Ford engineering number found on the back is C8AB-14507-B.

Used grade "A" bezel used on the passenger side door and both rear seat switches. Looks similar to the 1970 bezel but is held in place with very hard to find clips not speed nuts. No pits or obvious scratches, Ford engineering number as seen from the back is C9AB-14A432-DFord part # is C9AZ-14528-A

Used grade A power window switch bezel for the Mercury Cougar. This bezel is used with all power window switches, except for the driver side door, and was only used on the 1973 model. Ford engineering # D3MB-14528-DA.

Good used bezel with obvious scratches and or pits. This bezel was used on the passenger door and both sides of the back seat in 1969 and on some earlier 1970 Cougars. The Ford engineering number found on the back is C8AB-14507-B.

Used grade B power window switch bezel for the Mercury Cougar. This bezel is used with all the power window switches, except for the driver side door, and was used on the 1973 model only. B grade, expect rust pitting in the chrome. Ford engineering # D3MB-14528-DA.

Used bracket for holding either the emergency flasher or turn signal flasher on many Fords dating from 1963. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches to one of two different relay mounting brackets. Couple of different designs were also used. Additionally there is also a different style of flasher mounting bracket. See our related items.Replaces Ford part number C3AB-13351.

Used bracket for holding either the emergency flasher or turn signal flasher. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This holder attaches directly to the rear of the metal dash with a hex head machine screw.Replaces Ford part number C8AB-13351-A.

Used bracket for holding relays, either the emergency flasher or turn signal flashe. We find these mainly in 1969-70 Mercury Cougar and Ford Mustangs. This is one of two different brackets used for holding relays or flasher brackets. See our related items.Replaces Ford part number C9ZZ-14A301-A.

Used bracket for holding relays, either the emergency flasher or turn signal flasher. We find these mainly in 1970 Mercury Cougar and Ford Mustangs. This is one of two different brackets used for holding relays or flasher brackets. See our related items.Replaces Ford part number D0ZZ-14A301-A.

Used bracket for mounting the various relays found on 1967 Mercury Cougars, both standard and XR7 models. This bracket mounts under the dash off of another bracket (see 1967 Cougar Electrical Assembly Manual page 15).*Note - 1968 used a different bracket.Replaces Ford part number C7WB-14A301-B.

Used bracket for mounting the various relays found on 1968 Mercury Cougars, both standard and XR7 models. This bracket mounts under the fuse block and is roughly "Z" shaped as shown. *Note - 1967 used a different bracket.Replaces Ford part number C8WB-14A323-D.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with manual brakes. High quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford part # D1ZZ-13480-A.Here are some pictures of the 2008 Prowl Show hosted by the Cascade Cougar Club. Click on images to enlarge. ...

Bushing that goes to the inside of the brake booster pushrod. This is the early version of this part that is made of plastic, a later version was introduced in 1969 which was made of nylon and is/was more durable.Replaces Ford Part number C9AZ-2474-A

Reproduction bushing for the master cylinder push rod where the switch and brake pedal converge. Two required per car and the bushings are sold separately.Ford part number C5DZ-2B129-B

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...

Used 20 amp circuit breaker for either 69 - 70 or 71-73 Cougars.Mounted on the Starter solenoid in 69-70 cougars for convertible tops or power windows, and also on 71-73 Standard Cougars for convertible tops, power windows, heated back light, power seats or seat back release.On the 71-73 XR7 the circuit breaker was mounted next to the starter solenoid on a junction block. Different wire diagrams, owner / shop manuals list this circuit breaker in both locations, possibly due to multiple...

Used on 1967 Mercury Cougar and Ford Mustang for the air conditioning, located under the dash to the back of the ignition switch. 25 amp circuit breaker, identified in the Ford MPC as part number C5AB-14A065-F or C5AZ-14526-C. It is 1.25" x 0.80". Box is marked FASCO Type 4110. 25AMP 12V. Attached mounting tab is included.These are tested and guaranteed to work.

Used in 1968 Mercury Cougars for the sequential motor, located under the dash on a panel next to the fuse block.15amp circuit breaker, not clearly identifiable in the Ford MPC. It is 1.07" x 0.40" and has a single green dot. Box is marked Tung Sol, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's...

Used in 1967 Mercury Cougars for the stop lamp switch, located under the dash on a panel next to the fuse block.15amp circuit breaker, not clearly identifiable in the Ford MPC. It is 1.07" x 0.40". Box is marked 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. The MPC shows this circuit breaker was also used on 1965-66 Continental convertible and 1965 Thunderbird convertible. These are tested and guaranteed to work.*NOTE* Need help diagnosing a Cougar turn signal...

Used in 1969-70 Mercury Cougars for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.07" x 0.40" and has a single green dot. Box is marked Tung Sol, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Also fits 1969 and newer Mercury full size, 1970-71 CycloneFord part number C9MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the...

Used in 1971-73 Mercury Cougars and Ford Mustang for the stop lamps, located under the dash on a panel next to the fuse block.15amp circuit breaker. It is 1.25" x 13/16" and has a single green dot. Box is marked FASCO, 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. Ford part number D1MY-14526-A. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the...

Used on 1967-68 Mercury Cougar and Lincoln Continental for the tail lamps or running lights in the rear, located in the trunk drivers side upper rear corner. Also used on 1967 Mercury Cougar and Ford Thunderbird for the headlight vacuum solenoids, mounts on panel under the dash board for that application. This 5 amp circuit breaker cycles the rear taillights on and off and is not clearly identifiable in the Ford MPC. It is 1.25" x 0.80". Box is marked FASCO Type 4110. 5AMP 12V. Integrated...

Very hard to find clip that fastens the chrome power window switch bezel to the door panel. Two required per bezel. Ford part number D0AZ-14570-A. *NOTE* Early 1970 Models used the 1969 style of bezel and did not use this clip.Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

These clips are found on the power window swtiches of the 69 - 70 Cougar. Each power window switch has one of these clips and one of the J hook clips.6 small clips required per master switch panel, one for each window switch and two per lock out switch. 

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

These same clips are also found on the four rocker switches located in the center of the 1969-1970 XR7 dash pad. Do not bend the "J" shaped tab any further than is necessary to release the plug from the back of the switch as these break easily. There are 16 of these used on a Cougar with power windows in 1969, add the 8 in the dash of the XR7 Cougars and some cars have a total of 24.Replaces Ford part number C9AZ-14530.

This is one of the hardest clips to obtain on any year of Mercury Cougar. Two required per bezel for the three bezels located on the passenger door and the two bezels in the back seat. Do not pry your bezels off or these clips will break rather release the clip with a small screw driver by inserting it in the rectangular hole on either side. If you are struggling to remove one of these bezels keep in mind it is best to have two people with two screw drivers come in from both sides at the same...

Exact reproduction horn ring contact components for the standard horn ring used on two spoke steering wheels, replaces Ford part # C9AZ-13A805-B. Includes new hardware

Horn ring contact components for the standard horn ring found on 68-69 2 spoke steering wheels. Ford part number C9AZ-13A805-B. Not as shiny as the reproduction kit but the price is less and the quality is FoMoCo original all the way. Reference photo above is the order in which the parts are installed.

This windshield wiper delay governor mounts to the driver side firewall. To find where this mounts on the firewall, look for two dimples. Wiring is simple, unplug the windshield wiper harness and plug the male and female ends into the appropriate plugs on the controller. Sometimes called interval or delay wipers. *NOTE* Must be used in conjunction with a intermittent wiper delay switch.Part # C9ZB-17C476, MPC #'s C9ZZ-17C476-B or D0ZZ-17C476-B.

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Many 70 - 73 cars used 3 pin type switches for the optional automatic seatback release feature. Sold individually. Additionally, this switch for the 3/4 inch mounting hole was used on 1968-70 Full sized Ford such as Custom, 500, Galaxie, LTD, and XL models, full sized Mercury such as Monterey, Montclair, Marquis, and Park...

Used jumper wire for the door ajar switch as found on 1971-73 Mercury XR7's. One end has a spade connector for the ajar switch, the other end is a bullet connector to the main door harness. Fits both driver and passenger side, about 41 inches in length.Replaces Ford part number D1WB-10C865.