Electrical & Lighting

Reproduction side marker light socket with harness set. For all 1968 Mercury Cougar and Mercury Montego and Cyclone. This listing is for a pair of wiring harnesses with light sockets. The original sockets were a snug fit in the fender light housings. These sockets are a slightly larger diameter than original and work well with the reproduction housings, but you may need to enlarge the hole if you're using your original housings. These wiring harnesses look real sharp with our reproduction...

The D0WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and LED side marker bulbs on most 1970 and up Ford vehicles. An adapter is required for each side marker light (4 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on. When this happens all the rear bulbs may flash...

The D1WY-15A434-LSM LED Side Marker Light Adapter kit is required when the C9WY-13A366-AL or the TS-400 Sequential controller is installed with LED front turn signal and rear LED side marker bulbs on 1971 Cougars and other Ford vehicles with two rear side marker lights. An adapter is required for each rear side marker light (2 total). This adapter solves the problem where the side marker voltage feeds back through the front turn signal bulb when the running lights or headlights are turned on....

Coming from Western parts cars these brackets are unusually nice in comparison to what you will find in other regions. For and extra $1.50 we can include the mounting nuts. Right is the same as left, two brackets required per car, sold individually.

Good used light with no pits or scrapes. Does not include lens or pigtail with socket, does include mounting bracket with two nuts. The chrome body carries a C8GB-15A428-B engineering number and the pigtail has a C8WB-15A442-A engineering number imprinted on the wire. We usually only have one or two in stock of this caliber so do not be surprised when you try to place this in your cart and it shows 0 quantity. Even though this is the best we will ever have to offer off of a Western parts car...

This grade "B" light bezel will have minor blemishes in the chrome as shown. Good part for a driver as it will not have deep pits. Does not include pigtail or lens. Left is the same as right. To remove pigtail from your existing light wrap socket in cloth to protect and grip firmly with a pair of pliers, rock back and forth while pulling and the plug and socket assembly should come right out from the back side. Replaces Ford part # C8WY-15A201-C.

Ford never offered this socket / plug assembly on its own but we do from time to time get one that has a clean socket and no cuts in the wiring. You can often just twist and pull (after the bulb has been removed) and it will come right out of the chrome housing. The Ford engineering number imprinted on the wire is C8WB-15A442-A.

Used snap in socket / pigtail for the clock light on your 67 - 68 Cougar. Also fits many other applications.

Used under dash wiring harness repair plug and pigtail to the ignition switch light socket for the Mercury Cougar. This is part of the 14401 main under dash wiring harness.

Light socket harness for the headlight reminder option. Works in conjunction with dash light and buzzer. 1970 XR7 and Eliminator option, not for standard, non- Eliminator models. Ford part numbers D0WY-13B155-A and wire cast number D0WB-13B155-A.

Good used light used only on the 1967 automatic consoles. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...). If you choose to run the light without the diffuser it will shine bright as opposed to a warm glow.  Ford Part Number: C7ZZ-15A808B Fits 67 CougarFits 67 Mustang Check out our video on rebuilding...

Reproduction light used only on the 1967 automatic consoles. The only difference between this shift indicator light without console and with console is the diffuser. The diffusers pull off and interchange. This light harness is also known as the PRNDL light harness (park, reverse, neutral, ...). The 1967 light had a male / female black combination plug. If you choose to run the light without the diffuser it will shine bright as opposed to a warm glow. Ford Part Number: C7ZZ-15A808B Check out...

For use with factory and reproduction console parts on a 1968 Mercury Cougar or Ford Mustang. Plugs into your existing console wiring harness. Double male plug is 1968 only. Sold without light bulb. The supplier says this replaces Ford part number C7ZZ-15A808-B but that is incorrect as the Ford part number for 68 is C8ZZ-15A808-B. To use this on a 67 the plug would have to be changed to a male / female combo plug.

Reproduction shift indicator light for use on the 68 Cougar and Mustang without a center console. Plugs into your existing console wiring harness. Double male plug is 1968 only. 

Bulb and socket assembly that attaches to the back side of your instrument cluster housing on all 1968 Standard model Cougars. All electrical harnesses are inspected, professionally repaired (when needed), tested, and ready to install. Harness marked C8WB-10B942-E.Check out the video below on our new gauge tester: ...

Bulb and socket assembly that attaches to the back side of your instrument cluster housing on all 1968 XR7 model Cougars. All electrical harnesses are inspected, professionally repaired (when needed), tested, and ready to install. Harness marked C8WB-10B942-J.Check out the video below on our new gauge tester: ...

Used under dash wiring harness repair plug and pigtail to the dash mounted courtesy light on the Mercury Cougar. The socket is the same on both sides. This is part of the 14401 main under dash wiring harness.

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Not sure of the exact application for these original Ford stereo speaker wiring harnesses. We think that they may have come from the radio kits installed by Ford and Mercury dealers. Note the special speaker connector plugs. The individual right and left speaker wiring leads are about 40 inches in length from the center plug that goes to the radio or stereo. The paper tags are missing from these harnesses, but we are pretty sure that they begin with C8OA-19A041.One of our customers says that...

Good used and working speedometer from 1969-70 standard model Cougars. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work correctly. 1969 and 1970 standard speedometers all look exactly the same on the front, but the 1969 is white backed, and most of the 1970 ones are bare steel color. Replaces...

Used 1967-68 Mercury Cougar XR7 speedometer with trip meter, grade A condition. Grade A will be fully functioning, and good legible numbers on the trip meter portion. We also see grade B XR7 speedometers that have cosmetic problems, usually on the odometer or trip numbers.Ford part number C7WY-17255-C Put your desired odometer range in the comments section, and we will try and match it up as close as possible. This icon means that we're looking to buy this part!WCCC is a buyer of used and...

Used 1967-68 Mercury Cougar XR7 speedometer with trip meter, grade B condition. Grade B will be fully functioning, in most cases the trip meter numbers will be worn and not easy to read.  Put your desired odometer range in the comments section, and we will try and match it up as close as possible.Check out the video below on our new gauge tester: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an...

Good used and working speedometer from 1969-70 XR7's and Eliminators. Grade A used, tested and will have good numbers on the odometer section. (Our Grade B examples are fully functioning, but will have worn numbers on the odometer section. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work...

Good used and working speedometer from 1969-70 XR7's and Eliminators. Grade B used, tested and will have faded or missing numbers on the odometer section, generally the dials look black where the white numbers have worn or faded off. (Our Grade A examples are fully functioning, and will have legible numbers on the odometer section. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the...

Reproduction XR7 / Eliminator speedometer lens for the 1969 - 1970 Cougar. The difference between Standard and XR7, is that the XR7 and Eliminator have a trip odometer reset button embedded in the lens at 6 O'clock. Correct Convex shape made from modern UV resistant plastic.Check out the video below on our new gauge tester: ...

Very heavy duty counter balance spring for all 1969-70 Mercury Cougar door regulators with power windows. Original Ford part number C9WY-6523318-A. Power window regulators only, this spring is quite a bit larger than manual window regulator springs. Application also fits 1972 full sized Ford and Mercury station wagon power tailgate windows.

Good used grade "B" core plastic passenger side bezel that may have had one or more very minor cracks. One or more studs on the back may be broken as well. Finish will be poor or non existent and this bezel will have minor noticeable UV damage which makes them very brittle and prone to future damage.

Good used core plastic bezel that has had one or more cracks repaired as well as other areas of the plastic where pieces may have been replaced. The process of repair will show on the back side of the piece. There may be some sanding required to prep for a finish. Studs on the back side will be broken or missing. Finish will be very poor or non existent. Keep in mind that we can install a new metal stud on the back to assist in installation at an extra cost.

Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent.

Good used core plastic bezel that has had one or more cracks repaired. Finish will be poor or non existent.Ford part number: C7WF-10838

Good used core plastic bezel that has no cracks, no excuses. Finish will be poor or non existent. Check out our video on dash removal and restoration:

Good used core plastic bezel that has had one or more cracks repaired. Finish will be poor or non existent. Ford part number: C8WF-10838 Check out our video on dash removal and restoration:

These are all new, not rebuilt, concours quality. Features authentic markings and logo. Black case only. Disappointing quality, often will fail in less than a year, we recommend buying original FoMoCo.  Replaces Ford part # C6AZ-11450-A. *NOTE* There are dozens of styles which were produced by several manufacturers. These parts represent the most common type.

Replaces stop lamp relay on 1967 Cougars built before 1-3-67. No wiring modifications needed, just plug it in in place of your old mechanical relay in the trunk. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the...

New Old Stock relay. Known as the "K-11" relay in the Ford Service manual. This relay was only used in production prior to 1-3-67. It provides a low current circuit through the relay solenoid and the stop lamp switch and a separate circuit through the relay points to handle the higher current load of the stop lamps. Again, this unit was only used in early 1967 Mercury Cougars. This early brake light relay is unique to Cougars built prior to 1-3-67. Unlike the later built Cougars, it...

Known as the "K-11" relay in the Ford Service manual. This relay was only used in production prior to 1-3-67. It provides a low current circuit through the relay solenoid and the stop lamp switch and a separate circuit through the relay points to handle the higher current load of the stop lamps. Again, this unit was only used in early 1967 Mercury Cougars. This early brake light relay is unique to Cougars built prior to 1-3-67. Unlike the later built Cougars, it mounts next to the sequential...

Used stud and nut for inserting and attaching to used or reproduction side marker lenses. Red or amber lenses.

Reproduction mounting studs for the side marker light lenses on 1970 Cougars and Mustangs. 2 required per light, 8 per car.Sold as a pair.

Reproduction studs and nuts for the taillight to body on the 1969 - 1970 Mercury Cougar 

Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. NOS, new old stock part. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This reproduction A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel.  Save your knobs or consider purchasing the 1969-73 selector button kit, you can find them here.Ford part # C9ZZ-19986-A.

This A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel. We always test all of our electrical components and this is a good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit. Click this LINK for those little beauties.Ford part # C9ZZ-19986-A.

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on your Mercury Cougar or Ford Mustang. Good working switch and wiring pigtail with plug. Save your knobs or consider purchasing the 1969-73 selector button kit.Ford part # D1ZZ-19986-A.

Used air conditioning thermostat switch for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Ranco for Ford. Ford part numbers C7ZA-19618-C or C7ZZ-19618-A.

Used air conditioning thermostat switch for any 1971-73 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Cutler-Hammer for Ford. Ford part numbers D1ZA-19618-A or D1ZZ-19618-A.

Backup light switch for factory installed Hurst competition shifters from 1970-73. This is a Daniel Carpenter reproduction, these are still being made by Hurst in small quantities (see our premium version). It does not include the bracket for holding the switch.Listed in the Motorcraft catalog as SW-943Also fits:CometFairlaneMontegoTorino Check out our video on rebuilding your shifter below: ...