Body

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if yourrequirements for a cut are are different from what is shown, and often we can accommodate. This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel. You can find...

This plasma cut patch was taken from the complete skin we list. We do this because not only do some customers not want to replace the entire skin, but often our foreign customers do not want to pay freight for an entire panel. Give us an outline if your requirements for a cut are are different from what is shown, and often we can accommodate. This is a "full" cut, which means that vertically it reaches from the bottom of the panel all the way to the top of the panel....

Reproduction radiator / core support for Mercury Cougar and Ford Mustang. This is the very best one made! Replaces Ford part # C7ZZ-16138-B and C7ZZ-6510852-B together.

These are bolted to the rear frame rails and were used to tie the car down to the transporter for the journey from the factory to the dealer. The dealer was supposed to remove them and return them for a credit as instructed by the dealer. Notice the sticker on the rear license plate frame (decal is available in the decal section)? Many sets slipped through as the dealers often forgot or did not deem the small credit back worth their effort to remove. These are great for transporting your car...

For deck / trunk lids it is all about rust under the inner rear lip... We still check it over good for excessive filler, correct contour on all the lines and hidden rust under the weather strip. We ship deck / trunk lids with several layers of thick cardboard and insure them for the full amount. Keep in mind shipping is free if you order at the same time as a hood, door or quarter panel. For those wanting a cleaner look on their 1967-68 Cougar a 69-70 deck / trunk lid will bolt right on with...

Late 1968 Mercury Cougar trunk lid, identified by having the large square hole for installing the trunk lock and latch parts. This style is hard to keep in stock, please see the 1967-68 version in the related section. Most often the problem with our Grade "B" deck / trunk lids is rust under the lip. We do not sell "rotted out" deck / trunk lids. Like the deck / trunk lid shown here you will be able to sand blast it and treat the rust so as to prevent it from spreading. We almost guarantee that...

Most often the problem with our Grade "B" deck / trunk lids is rust under the lip. We do not sell "rotted out" deck / trunk lids. Like the deck / trunk lid shown here you will be able to sand blast it and treat the rust so as to prevent it from spreading. We almost guarantee that at least "some" pin holes will appear after you have blasted the underside. Make sure to click onto our "after" shot to see what you should expect to see after you have bead blasted the underside of one of our "B"...

Used trunk or luggage compartment latch, fits all 1967-73 Mercury Cougar and many other Ford and Mercury cars. Comes with 3 bolts for mounting.Replaces Ford part number C5AZ-6243200-A.

Reproduction deck lid for the 67-68 Cougar. Exact reproductions of the originals, these deck lids are well fitting and are a perfect replacement for your old rusty lid.  Does not include hardware or lock cylinder, shipped bare. Here's the installation kit for these reproduction deck lids. Keep in mind that this is an oversized package and will most likely have to be shipped through truck freight. Expect to pay up to $250 in shipping charges. ...

Reproduction driver side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps ...

Reproduction passenger side rear extended floor pan for the 67 - 68 Cougar or Mustang. NOTE: This quality pan can be modified to fit a Cougar, but is designed for the Mustang. You can see in the picture above that when being installed on the Cougar, there will be a sizeable gap along the wheel well. We also carry used patches to fill those gaps. ...

Driver side, rear frame rail, from a 1968 Mercury Cougar. Full length, we cut so that there is some remaining metal on the edges. 1968 was the first year where the inside part of the frame rail has a large access hole for inserting the leaf spring bolt. The large access hole normally should have a plastic body plug to prevent debris from entering the frame rail. Ford part number C8WY-6510125-A.* Note - this item has dimensions in excess of 75 inches, and will ship as "Over- Size",...

Passenger side, rear frame rail, from a 1968 Mercury Cougar. Full length, we cut so that there is some remaining metal on the edges. 1968 was the first year where the inside part of the frame rail has a large access hole for inserting the leaf spring bolt. The large access hole normally should have a plastic body plug to prevent debris from entering the frame rail. Ford part number C8WY-6510124-A.* Note - this item has dimensions in excess of 75 inches, and will ship as "Over- Size",...

Reproduction driver side rear inner apron for both the Mercury Cougar and Ford Mustang.

Reproduction passenger side rear apron for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

[No Description Provided]

[No Description Provided]

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Reproduction pair of lower fender braces. The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Good used L bracket that is not heavily rusted or bent. Passenger side is marked from the factory with an "R" and driver side is marked with an "L". The portion with the lip mounts vertically and the purpose of the lip is to align the splash shield into the proper location.

Our grade "A" rear quarter panel extensions have no obvious dings, scrapes, bumper contact damage or warping due to over tightening of studs. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

New old stock passenger side rear quarter panel extension. 1967-68 Mercury Cougar. Ford casting # C7WB-6527702-A, Mercury MPC # C7WY-6528072-A. Do you have questions about your Cat's factory pinstriping? This link may help.

Rear fender splash shield for the driver side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16103-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

Rear fender splash shield for the passenger side rear inner fender. In most cases, these used shields will need to have the stapled rubber shields replaced. Ford part # C7ZZ-16102-B. *Installation & detailing tip* Front fender splash shields are attached to the fender, rear shields are attached to the body. After the fender is installed, this is the right time to apply the undercoating material. This ensures that there is a good seal to prevent water splashing from the tires. ...

Reproduction rear taillight panel lower structure / support for the 67 - 68 Cougar. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

This area of the door often cracks due to the stress caused by worn out hinges. This twelve piece kit includes six screws and six form fitting washers to reinforce the recessed areas that often crack. If your latch area is badly cracked you will want to purchase the repair kit that requires being welded in.

This pair of plates cut from 11 gauge steel (1/8") are designed to be welded onto the front crossmember that braces the front frame rails and ties together the lower control arm pivots in a superior way to the original design. When welded onto the front crossmember properly, these plates will prevent any camber change in hard cornering. This is not needed for the average Cougar owner, but if you are desiring to make your car a "Handling Machine", every bit counts. This combined with our shock...

New pair of weld in shock tower reinforcement plates cut from 11 gauge steel (1/8") for the Mercury Cougar or Ford Mustang. It is common knowledge that one of the main design flaws of the early Cougar or Mustang are the shock towers. Because of this design flaw, it is common (even with pampered, low mile, completely stock cream puffs) for the shock towers to have some degree of cracking as they were never designed to fit an oversized wheel and tire package, be cornered hard or handle the heavy...

High quality chrome finish on lever & base. Improved cable for smooth operation. You must have correct trunk latch to use this remote. Detailed instructions included. Look for the trunk latch in our 'related items' tab.

New old stock Ford accessory cable trunk popper. Fits late 1967 - 1973 Mercury Cougar and other Ford products. Lever release, cable and hardware, NOS Ford. Detailed instructions included. Latch not included with this kit. Sorry, the way it came. This kit was a dealer sold kit or over the counter kit. Fits a large range of Ford cars. Ford part number C4AZ-62432A00-A. *Note - All 1967, and most 1968 trunk lids will not have a large enough access opening in the under side structure to...

This is an upgrade to the Electronic Trunk Release. Allows trunk to be opened with just the push of a button on two wireless remotes that are included. NOTE: This item requires that you have a latch mechanism equipped with the remote release tab.

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

This strip has a series of seven retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.

This strip has a series of five retaining clips that hold the headlining panel to the roof panels as seen on page 14 of the sun roof manual.This is for the 1971-73 Mercury Cougar with factory sunroof. Sunroof measurements are roughly 19-1/2 x 39 inches. This panel is 32-1/4 inches long with 5 clips as shown.

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade A's will have no scratches or dings.Ford part number C8ZZ-17B719-A

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade B's will have minor scratches or dings. Ford part number C8ZZ-17B719-A

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

This is the nylon roller that fits on the end of the window regulator arms. Includes rivet.Sold individually. 2 rollers required per window, 4 rollers required per car.Replaces Ford part number C5AZ-57262A32-A. Dimensions: 11/16" DiameterHere's an instructional video on how to install the rollers. Keep in mind that this is a YouTube video from Danchuk Manufacturing installing a different type roller, but the technique is the same: 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction roof / headliner insulation kit for your Mercury Cougar or Ford Mustang. An effective item that will increase the efficiency of your heater or A/C. This will also insulate your interior from outside sounds.

Reproduction roof brace for the 67 - 68 Cougar or Mustang. This is the leading front support on your roof, directly above your windshield.

Reproduction roof repair kit that includes the roof skin, C pillars and the rear window channel for the 67 - 68 Mercury Cougar. C pillars are cut from our reproduction quarter panels. This kit must ship via truck freight. Expect to pay $400 or more to have these items shipped. Our online shipping calculator is not very accurate for truck freight items so we encourage you not to pay for the order up front but rather bypass paying for your order by selecting "contact us for...

Good used center reinforcement beam, or structural brace section for the roof skin. It does not actually attach to the roof skin. Attaches to unitized structure of the roof frame sides. Ford part number is 50222, or 6550244.

In the past, you would have had to purchase a used roof cut from a parts car which meant that you would most likely have do a bit of work to get it straight and clean enough for paint. But now our friends over at Dynacorn have finally come through with a quality reproduction roof panel skin for the 1967-68 Mercury Cougar. If you need a partial roof we can cut this part down to your specifications with a plasma cutter. The price will remain the same but if you need only a half of a roof you...