Body

New template to make your own package tray cover for the Mercury Cougar. Package trays are difficult to package and can be costly to ship.  This template will assist you in making your own. *NOTE* There is a slight difference in size between 1967 and 1968 package trays.

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

This specially machined screw tensions the friction clutch assembly in the gearbox.

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.

Reproduction passenger side (left hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Reproduction torque box gusset for your 67 - 70 Cougar or Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box for extra strength. Sold as a pair.

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.

These long rods are installed horizontally in your trunk and attach to the trunk lid hinges. We only remove these bars in pairs from cars that demonstrate that they can in fact support the weight of the deck lid on their own. We do not save rusty, bent or weak springs. These are the best we have to offer from our Western parts cars. 1967-70 torsion springs C7WY-6544890-A and C7WY-44891-A. Limited to supply on hand. The body section of the shop manuals describe how to adjust these bars, we...

Reproduction transition panel for the 67 - 70 Cougar. This is a complete replacement for the factory spot-welded-in panel, not a partial cut. For more info on this new trunk panel, check out this video below:

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Used transmission tunnel specialty cut. If you choose not to purchase the entire floor pan, you can buy the individual full length floor pans and opt for this specialty cut of the full length transmission tunnel. We will give enough "meat" on all sides to meet up with the firewall, floor pans and rear seat area. If you'd like a smaller section, you can tape off the area you're working on and send us a few digital pictures so we can cut to your needs. Pricing may not change, because we're...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

Reproduction driver side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Driver side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1967-68 Mercury Cougar. These special cuts are removed from rust free examples from a used Cougar. Ford part number C7WY-6545119-A.

Reproduction passenger side taillight panel corner patch for the 67 - 68 Mercury Cougar. If your taillight panel is rusty in the corners, this patch will save you a lot of money in shipping costs as opposed to ordering the entire taillight structure. You can find the taillight panel here.

Passenger side, rear, lower corner, special cut that ties the quarter panel with the tail light panel on any 1967-68 Mercury Cougar. These special cuts are removed from rust free examples from a used Cougar. Ford part number C7WY-6545118-A.

Used cover with dull chrome. This used to be a very sought after and expensive part due to how difficult they were to find. Now that our show quality reproductions are here they have little value... Great for someone that just wants their driver to look complete. Fits all 1967-68 Mercury Cougars, Standard and XR7 models. Decal inserts available separately. Check out this video

For 1967 both the XR7 and Standard model used the decal shown on this reproduction trunk lock cover. For 1968 only the Standard model used this decal as the XR7 and XR7G had their own unique center badging. *NOTE* You will have to apply the licensed by Ford decal to the deck lock cover. Check out this video

This is for the person who already has a decal or XR7G emblem to place in the center section. Maybe you have a custom idea? Same great quality and flawless fit as our other deck lock covers. *NOTE* After a long hiatus these are finally back in stock! They were worth the wait, the quality is really good on this new reproduction. Check out this video

Beautiful reproduction truck lock cover with new XR-7 decal. Very true to original, the only noticeable difference being that the corners of the decal are slightly more trimmed than the originals. Check out this video

Save your hard earned money when you buy our reproduction deck lock cover with the new XR7-G emblem already installed! Check out this video

This reproduction is pathetic... It's made from the same material as a cheap picnic table cloth (you know, the red checkered ones?) The only way you will ever get this plastic "table cloth type" mat to lay flat is to glue it down. They do however work well for catching oil spills under your Cougar when turned felt side up. No returns on this product, we suggest no mat is a better alternative than this poor quality reproduction. It's that bad... Please look at our premium quality trunk...

This is the best made, most correct Mercury Cougar trunk mat on the market (Mustang mats will not fit). Made of heavy die-cut vinyl with correct gray and black plaid pattern by Auto Custom Carpets. Do NOT confuse this with the light duty mat you will see elsewhere listed for the same money or less. The budget mats you see elsewhere weigh only a few ounces and flail around inside your trunk every time you close the lid! The pattern will not smudge or wear off easily and it will lay flat and fit...

Complete reproduction trunk floor pan for the 67 - 68 Cougar. Also includes rear shock support, axle bumper mount, and rubber plugs for the shock holes. When ordering this item, keep in mind that it is an over-sized box which will be drop shipped from our supplier in California or available for in store pick up at WCCC. You can expect to pay up to a few hundred dollars for shipping (oversized items must be truck freighted). Often, all you need is the left or right trunk sections. You can save...

Complete non assembled trunk pan kit. Included are the transition panel, trunk floors, rear taillight support and shock support. This kit will require you to assemble and weld in all individual pieces of the rear trunk pan on your own.  This is an oversized box, so expect to pay about $300 for shipping, depending on location.

Replacement U-nut or clip for any 1967-70 Mercury Cougar trunk lid. These slide into the bottom of the trunk lid for attaching the hinges. Correct 5/16-18 threads, 7/8" from center of hole to edge. 4 total per trunk lid, sold individually.

Sold individually, two per side, four per car required. These often get destroyed when you go to replace your door window regulator slides. Two of these are used to install the C7ZZ-6523288-A track. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size)Not sure where to begin when it comes to replacing your window regulator? Check out our how-to video...

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 681

Curved aluminum cable guide as seen on page 13 of the sun roof manual. Golde part number 100 413 682

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part #: C7ZZ-6522800-C. ...

Most times you do not need new hinges but rather new bushings and pins. If your hinges are such that the holes are "hogged out" and no longer seat the bushing firmly then you will need to buy one of our good used hinges that come with new bushings and pin. These overseas hinges are not known for fitting well, we cannot recommend them and we do not accept returns or exchanges on them. Replaces Ford part # C7ZZ-6522800-C.

This is a reproduction front valance for your Mercury Cougar. This valance is an excellent reproduction in every detail. Below are pictures of it next to a NOS valance for comparison sake. As you will see, this is an "A" class reproduction in every aspect. Rarely is a reproduction ever a match in any way to NOS. This one is an exception to the rule!Click on images to enlarge. The fasteners for the license plate are just slightly different but the function and placement are dead on.  These...

These reproduction valances have been modified and fitted with high quality reproduction XR7G fog light buckets. When you compare an original valance to these you will see much more care was given than in the originals when placing the buckets. These will require minimal finish work where the buckets were welded to the valance. This is a limited production run only available from WCCC.Replaces Ford part number C8WY-17620

Very Limited supply. Keep in mind that when ordering multiple oversized items from us online that the shopping cart does not know how to best combine items to save you the most money. We suggest cutting and pasting your order into an email so we can manually calculate shipping costs.

THERE ARE NO RETURNS ON THIS PART. Not a good fit but you can make them work...You will have to elongate a couple of the small holes that mount the valance under the bumper, but not by much. Once mounted the part looks as though it was not made quite wide enough. We recommend purchasing our premium version, because honestly, you'll spend a lot of time trying to get this offshore reproduction to fit right.  Please do not call us and say you are disappointed with this part; we are telling...

Premium reproduction rear valance for the 67 - 68 Cougar. This valance is a direct fit, as opposed to our economy version which take a bit of modifying just to be installed and will never look like if really fits right. This premium valance is very durable weighing in at 5.12 pounds, compared to an original which weighs 4.11 pounds. Replaces Ford part # C7WY-65405144-A. ...

We have a very hard time keeping these NOS rear lower valences in stock. Since the reproductions don't quite fit right, NOS and good used are the best options at this time.Ford part # C7WY-6540544-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store...

Complete four piece door vapor barrier kit specifically cut for the year of your Cougar.

New old stock passenger side vent window handle for any 1968 Mercury Cougar or Ford Mustang.  Drive pins and washers included.Ford part number C8OZ-5422916-B.

Pressure die cast in zinc and heavily chrome plated. Excellent quality. Drive pins and washers included, sold as a pair.

High quality reproduction black vinyl top for the Mercury Cougar that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than any economy priced version. Thinking about installing this unit yourself? Check out our video below for some inspiration. ...

Reproduction black vinyl top that looks good and fits perfect. This top has the correct pattern, however the finish is a bit shiny and will not look original to the discriminating eye. Also, the backing is a white felt material which is prone to trapping moisture and causing your roof to rust. The original tops had a more durable canvas-like backing. This top will also have a seam in the A pillar. If you're doing a high quality restoration, we recommend our Concours vinyl tops. <a...

High quality reproduction black vinyl top for the Mercury Cougar equipped with a factory sunroof that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than our economy priced version. This unit is for the Cougar owner who demands premium correct parts for his or her prized feline. Thinking about installing this unit yourself? Check out our video below for some inspiration. Below are...

High quality reproduction white vinyl top for the Mercury Cougar that features both the correct pattern and finish. This concours correct top also features a durable moisture resistant backing that will look better and last longer than our economy priced version. This unit is for the Cougar owner who demands premium correct parts for his or her prized feline. Please allow 2 - 3 weeks for delivery. Thinking about installing this unit yourself? Check out our video below for some inspiration....