Body

These two original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

These two original hinges have been rebuilt with steel sleeves to retain the over-sized oil impregnated bushings. They feature hollow hinge pins which allows grease to fill the steel tube, lubricating the bushings under pressure from the inside-out. The threaded Zerk fittings are easily accessible from inside the car when the door is opened and are guaranteed to NEVER wear out or we will rebuild them for FREE! This offer has been in place for 20+ years by our rebuilder and they have never been...

Whenever you take on a door job, its always handy to have a few things available....a helper, a floor jack and a door hinge wrench. While a helper and floor jack might not always be available, a door hinge wrench is a valuable tool to have around when removing / setting a door. This Snap on obstruction wrench (google snap on part # S9608B) is specially curved to allow you to gain access to a few of those hard to reach bolts on your door hinges. We will loan this door hinge wrench for 60 days,...

Used original door latch rod for the interior push button lock on the passenger side (right hand) of the Mercury Cougar or Ford Mustang.Ford part # C8ZZ-6521852-A.

This is an original chrome lock knob used on 1968 and up Fords with no peeling chrome or obvious scratches. If you compare the originals to the reproductions we have listed you will see a distinct difference. This is for the very particular restorer who really is concerned about detail, especially on prominent pieces like this. Sold individually, very limited supply.Original Ford part number is C8AZ-6221850-A

Good original passenger side door latch rod set. Includes rod for inside lock, outside key lock, and outside door release actuating rod. These are good used parts and are a better quality and value compared to the reproductions. Only fits passenger side doors of 1968 Mercury Cougar and Ford Mustang. 1968 door latches are unique, they have a longer tab for the inside door lock knob typically. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers...

Here is an example of what you can expect from a grade "A" pair of 1968 decor door panels from us. These are given the grade "A" rating because there is minimal discoloration of the mylar trim surrounding the horizontal basket weave pattern, chrome peeling from the walling cat emblem and light general wear. These panels are very hard to find in grade "A" condition. Keep in mind these listings are just a sample of what we often have on hand. We are not able to list all of our used panels and...

Here is an example of what you can expect from a grade "A" pair of 1968 decor door panels from us. These are given the grade "A" rating because there is minimal discoloration and light general wear. These panels are very hard to find in grade "A" condition. Keep in mind these listings are just a sample of what we often have on hand. We are not able to list all of our used panels and ask that you email or call for stock on hand. Most of our panels range in price from $250-$600.NOTE: The...

Here is an example of what you can expect from a grade "B" pair of 1968 decor door panels from us. These are given the grade "B" rating because of the obvious wear and discoloration. These panels are very hard to find in grade "A" condition. Most of our panels range in price from $250-$550. NOTE: The pictures shown here are file photos from sets we have sold in the past and are not the actual panels or color you will receive. Please email or call for current colors and conditions of stock on...

The Best To Be Found. Grade "A" doors have never been dented in, cracked in the door latch area or rusted along the bottom seam. There are no drilled holes for an after market impact strip and the sound deadener is still intact. Occasionally it will still bear the original paint but do expect multiple small door dings. This is the best condition Western door you could ever hope to find, satisfaction guaranteed. Included in the price is a wooden crate, discount applies when you pick it up in...

The Best To Be Found. Grade "A" doors have never been dented in, cracked in the door latch area or rusted along the bottom seam. There are no drilled holes for an after market impact strip and the sound deadener is still intact. Occasionally it will still bear the original paint but do expect multiple small door dings. This is the best condition Western door you could ever hope to find, satisfaction guaranteed. Included in the price is a wooden crate, discount applies when you pick it up in...

These NOS sill plates always have some degree of shelf wear due to the many years they have been shuffled around. The biggest difference you will see with NOS vs. the two different levels of reproductions is the finish. The NOS parts are far less bright and less prone to showing hairline scratches. One other benefit is that NOS sill plates already have the FORD decal in place. Sold individually.

These interchange left to right, they are a mirror image of one another. We recently did a side by side comparison of these so called "concours" sill plates and found very little difference when comparing them to the "economy" version... They both weigh .52 pounds, just like our NOS sill plates. They both have a high of luster, unlike the originals which featured very little "shine". We found the screw holes to be just a tad larger on the economy version but once the screw is inserted you...

We often list items like this more for documentation purposes than as an actual sale item. We have no XR7-G pull straps for sale at present, but this photo may be of help to those of you that are looking to restore or recreate a pair.

This is the gear on the upper side of the gearbox. The cables go over each side of the gear.NOTE: Be sure the gear is in good condition so your cables don't get worn out!

Used end cap with the burl woodgrain for the deluxe door pull straps found in the Mercury Cougar XR7 or Ford Mustang. These units will show a degree of pitting, fine scratches and fading. Also, these door pull strap caps are unique to 1968 and they are not currently being reproduced. 1967 has no border and the woodgrain has a different color and look to it. This is for the person that must have correctness in detail or they just need one to finish off their interior. We highly recommend...

Chassis black aerosal paint for all 1967-73 Mercury Cougar and Ford Mustang engine compartments. High temperature (advertised up to 350°). Manufacturer boasts resistant to cracking and flaking, chemical resistant to gasoline and brake fluid (but don't let brake fluid accumulate). *NOTE* Chemicals can only ship UPS ground only. Please, no foreign orders or USPS shipping allowed.Check out our video below on chassis upgrades: ...

New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP125 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...

Scott Drake used the original Ford prints to makes these exactly as the originals with heavier gauge steel than the other reproductions we have seen. Unlike the reproductions of the past, these actually fit without the need for modification or the need to jump on the front of the car to install. They are the best braces on the market today by far... Greatly reduces twisting of the chassis. Also strengthens the front end and helps reduce shock tower fatigue and cracking. Also available in Black...

This latest of a series of 68 reproduction sheet metal parts is just what the market has been waiting for! The dimensions are EXACT down to the 1/16", black primer finish is very similar to what the later service replacement parts were from Ford. The fender weighs a few pounds more than original due to being made from slightly thicker material than OEM. Keep in mind there are no shipping fees or taxes when you pick this item up in person at our shop. Next up will be deck lids, stay tuned!...

Our grade "A" 1967 - 1968 fender extensions have no obvious dings, scrapes or warping due to over tightening of studs. Hardware not included but if you ask for it we will try to include it at no charge. Note that the inner part just behind the eyebrow moulding is painted black from the factory.Ford casting number as seen from the back side reads C7WB-16019-A. Do you have questions about your Cat’s factory pinstriping? This link may help. This icon means that we're looking to buy this...

This assembly is spot welded to the fender skin. Sometimes this area will be damaged in a collision but the skin will still be fine. Due to the rarity of good fenders and the costly shipping you may want to consider repairing your fender as opposed to buying another if this is all you need.

Reproduction passenger side (right hand) floor pan to firewall extension for the 67-68 Cougar.

These are hand made buckets to turn a regular 1967-68 Cougar front valance into a XR7-G valance and they come with templates and instructions. To get an even better idea how they should be installed, take a look at our used XR7-G valance. ...

Reproduction driver side (left hand) outer front frame patch for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Reproduction inner floor frame rail patch for the Mercury Cougar and Ford Mustang coupe and convertible. As this item is for a Mustang, you will find that you will have to modify it to work with your Cougar. This unit measures 28" long where the Cougar piece is 19". This unit is a 1/4" wider than the Cougar piece as well.

Reproduction passenger side (right hand) outer frame rail patch for Mercury Cougar or Ford Mustang.Here's our little film to help you fortify your flexxy feline!

This part is located in the left front corner of the panel and has to be rotated inward to remove it from the guide rail so the panel cannot be removed. Imprinted on the plastic portion of the part is a Golde part number 100 414 645. Ford part number C8WY-65502L09-A

Must have for 69-70 convertible owners or anyone else who wishes to tighten up the notoriously weak front inner structure of the 67-70 Cougar / Mustang. All three of these easy to install upgrades are outlined in the BOSS 302 Chassis Modification book that is NOT included in this package. After you install this kit you will wonder how you could have possibly lived this long without it. Even if you already have the one piece export brace, the chances are it is the old ill fitting off-shore...

Contrary to what you might think at first glance, the support rods used in 1967 - 1968 Cougar headliners are not the same front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must keep the rods in the same order as they came out of the original headliner. To help you do this, Lincoln-Mercury coded each rod with a color applied to each end. From front to rear, the 1967 - 1968 color codes of the headliner rods are: None Red White Brown...

Reproduction NUGGET GOLD Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction SADDLE Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of installing...

Reproduction MAROON Sunroof Headliner for the 1967 and 168 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of installing...

Reproduction SADDLE Sunroof Headliner for the 1967 and 1968 Mercury Cougar or Ford Mustang. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking...

Reproduction DARK BLUE Headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of installing your...

Pair of used wire anchors for keeping the rear most headliner bow stationary. These are fragile wires, and prone to rusting. We try to keep them in inventory. 1967-68 anchor wires are 5-9/16 inches long. A DIY person can improvise these pretty easy, using lengths of regular wire. Ford part # C4OB-6252180.

Reproduction frame used to stretch your headliner over on the interior side of your sliding sunroof panel. Since we do not have near enough of these to go around we also offer a cardboard template for purchase for those of you that would like to make your own. With the pictures we provide and the template one should be able to produce a reasonable reproduction. 

Good used frame used to stretch your head liner over on the interior side of your sliding sun roof panel. The picture above is the support strip that runs through the middle At its widest points this frame measures 35 1/4" x 20 15/16" ...

Crating Fee Applies To This Item. You will be contacted once your order is reviewed to discuss the crating fee. Crating fees generally run between $175 - $250 (this does not include truck freight charges). If an item has a crating fee, this usually indicates that it must ship via Truck Freight and can only be shipped to US addresses and select Canadian addresses. We rarely have in stock what we would consider a grade "A" 1967 - 1968 Mercury Cougar hood. Grade "A" 1967 - 1968 hoods have no rust...

Very rare find...NOS Sheet-metal is getting very hard to come by these days. And even at these exorbitant prices we have a hard time keeping many NOS body panels in stock. The best place to find NOS Sheet-metal these days would be at major national swap meets like the All Ford swap meet held in Carlisle Pennsylvania each year in June.Ford part # C7WY-16612-A.

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. Painted a satin black color. New old stock hood hinge without the spring. These hinges will work for 1970 Cougars, but because the grill center was attached to the hood during this year. The spring is heavier duty than 1967-69.Ford part # C5AZ-16797-B, C8AZ-16797-A, or C9AZ-16797-A.Anghel Restorations offers a very detailed breakdown of the differences in the Cougar and Mustang hood hinges. ...

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

Service replacement NOS passenger side hood hinge for Mercury Cougar and Ford Mustangs. 1978 manufactured date, this one is painted a gloss black color. New old stock hood hinge less spring. These hinges will work on 1970 Cougars, but because the grill center is attached to the hood during that year. The hood hinge requires heavier duty springs to accommodate the additional weight on the hood.Ford part # C5AZ-16796-B, C8AZ-16796-A, and C9AZ-16796-A.Anghel Restorations offers a very detailed...

If you are not looking to match the part numbers of your original hinges, we recommend considering our PREMIUM quality reproduction that is made of thicker material than the originals for added durability and is far superior to any previous reproduction. This listing is for you folks out there who want the correct part number on your hinge. Good used OEM original hood hinges that are available individually or as a set.   We carefully inspect these hinges before sending them...

New high quality fiberglass hood for the 1967 - 1968 Mercury Cougar. Inspired by the XR7-G hood scoop, our supplier molded these hoods with this taller functional hood scoop already attached (keep in mind that the original XR7-G and GT-E hood scoops are non-functional). The "nostrils" of the scoop are cut out, and there is a large opening beneath the scoop to provide extra airflow to the engine. This version of the G-Force hood has a molded fiberglass under structure (as...

New high quality fiberglass hood for the 1967 - 1968 Mercury Cougar. Inspired by the XR7-G hood scoop, our supplier molded these hoods with this taller functional hood scoop already attached (keep in mind that the original XR7-G and GT-E hood scoops are non-functional). The "nostrils" of the scoop are cut out, and there is a large opening beneath the scoop to provide extra airflow to the engine. This version of the G-Force hood has a steel under structure that is taken from an original...

Ultra rare item, subject to availability. Call about spent cylinders, we actively seek out those too. Our guess is that the contents of an NOS cylinder may be unstable for use.

Universal driver side (left hand) or passenger side (right hand) inner floor frame patch that you can trim to fit the area that needs to be repaired.